RVCCH-75WT - Unknown CRUX - Free user manual and instructions

Product Type	Reverse Camera Interface with A/V Input
Brand	CRUX
Model	RVCCH-75WT
Compatible Radio	MyGig Navigation Radio
Vehicle Compatibility	Jeep Wrangler 2007-2017
Input Type	Audio/Video Input
Camera Included	Spare Tire Mount Reverse Camera (CH-01S)
Power Supply	12V DC (Vehicle Battery)
Connection Type	Plug-and-Play T-harness with WHITE and GRAY connectors
Parking Guidelines	Adjustable via cut/disconnect white loop wire
Video in Motion	Available with connection to GREEN wire (+12V) for non-permanent operation
Manual Transmission Support	Yes (requires tapping camera power from reverse light wire)
Installation Complexity	Moderate (requires removal of spare tire and radio)
DIP Switch Settings	Configurable for vehicle-specific settings
Includes	CH-75WT module, T-harness, camera (CH-01S), mounting bracket, star washers
Dimensions (Module)	Approx. 3 x 2 x 1 inches (76 x 51 x 25 mm)
Weight (Kit)	Approx. 1.5 lbs (0.68 kg)
Maintenance	Keep connectors dry and clean; periodically check cable routing for damage
Safety Warnings	Insulate unused wires to prevent short circuits; ensure secure mounting of camera
Repairability	Components are non-serviceable; replace defective parts

Frequently Asked Questions - RVCCH-75WT CRUX

Is the CRUX RVCCH-75WT compatible with all Jeep Wrangler models?

It is compatible with Jeep Wrangler models from 2007 to 2017 equipped with the MyGig Navigation Radio.

Can I install the camera on a manual transmission vehicle?

Yes, but the camera power must be tapped from the +12V reverse light wire instead of using the WHITE 12V Reverse Output wire, which should be insulated to prevent shorting.

How do I enable the parking guidelines?

Cut or disconnect the white loop wire located near the 4-pin camera connector to activate the parking lines.

What do the parking line colors mean?

Green line indicates clear zone; yellow line indicates getting close; red line indicates warning - very close.

How do I access video sources after installation?

Press the RADIO/MEDIA button on the left side of the radio. The VES button will appear and allow you to switch to the A/V Input source. The VES button is only active after the interface is properly installed.

Does the interface support Video in Motion?

Yes, connect the GREEN wire to +12V for a non-permanent Video in Motion feature. Note that this may not work on manual transmission vehicles.

What DIP switch settings are required?

Refer to the installation chart (included in the manual) to set the correct DIP switch configuration for your vehicle.

How do I install the spare tire mount camera?

Remove the outside mounted spare tire, mount the camera's metal bracket onto the spare tire bolts, and secure with the provided star washers. Then route the cable towards the radio.

What is the purpose of the WHITE 12V Reverse Output wire?

It is used to power the camera on automatic transmission vehicles. On manual transmissions, do not use this wire; instead, tap camera power from the reverse light wire.

Can I use the A/V Input for aftermarket devices?

Yes, the interface includes an Audio/Video Input that allows you to connect an extra A/V source, which can be accessed via the VES source button.

USER MANUAL RVCCH-75WT CRUX

• Interface includes Audio / Video Input to connect an extra A/V source.
• Spare Tire mount reverse camera included.
• Activates MYGIG Screen for enabling Video features.
• Supports vehicles with manual transmission. See note below.
• Plug and Play connections for ease of use.

NOTE: Does not supply +12V Reverse Trigger on vehicles with manual transmission. Camera power must be tapped from the +12V reverse light wire instead. Video in Motion will not work for manual transmissions.

COMPATIBLE RADIO:

- MyGig Navigation Radio

PARTS INCLUDED:

CH-75WT MODULE

CH-75WT HARNESS

CH-01S CAMERA

1/3

Rev.092617

INSTALLATION DIAGRAM:

INSTALLATION:

1. Remove the outside mounted spare tire.
2. Mount the camera's metal bracket onto the spare tire bolts and secure with the star washers.
3. Route the cable towards the radio and make the power and video connections.
4. Remove the factory radio to gain access to the factory connectors.
5. Plug in the T-harness with WHITE and GRAY connectors. (See Wiring Diagram above)
6. Connect the 8-pin Molex connector from the T-harness with GRAY connectors to the CAN Interface.
7. Use the WHITE 12V Reverse Output wire to power the camera (see Wiring Diagram above). DO NOT connect the red power wire, near the camera, to the reverse light and insulate this red wire to avoid from shorting. If the vehicle has a manual transmission, the camera power must be tapped to the +12V reverse light wire instead. In this case the WHITE 12V Reverse Output wire is not used and should be insulated to avoid from shorting.
8. Plug in the YELLOW MALE RCA from the camera cable to the YELLOW FEMALE RCA of the T-Harness with WHITE connectors.
9. Connect GREEN wire to +12V for a non permanent Video in Motion feature.
10. Set the proper DIP Switch settings on the CAN Interface. (See Chart above)
11. Cut the thin white wire on the camera cable to enable the parking guide lines.
12. Test the camera before re-installing the radio.

PARKING LINES:

The parking lines are there to assist you while reversing. To activate the parking lines simply cut/disconnect the WHITE loop wire located near the 4 pin camera connector.

What the Lines mean:

Green Line: CLEAR

Yellow Line: GETTING CLOSE

Red Line: WARNING - VERY CLOSE

SWITCHING SOURCES:

VES will be your source for the AV Input.

HDD

DISC

AUX

VES

To access the VES button, press the RADIO/MEDIA button on the left side of the radio. The VES button is only active after the interface is properly installed.

VEHICLE APPLICATIONS:

JEEP

2007-2017 WRANGLER

COMPATIBLE RADIO:

MyGig Radio