KAVACSTM10X - Vacuum Cleaner Kogan - Free user manual and instructions

USER MANUAL KAVACSTM10X Kogan

Line drawing of a vacuum cleaner with handle and base (no text or symbols)

MX10 PRO CORDLESS 22.2V MOP AND STICK VACUUM CLEANER

KAVACSTM10X

SAFETY & WARNINGS

When using an electrical appliance basic safety precautions should always be followed including the following:

Kogan.com is not liable for damage caused by failure to comply with the use requirements, negligent use, etc.

• Children aged 8 years and above or persons with reduced physical, sensory or mental capabilities should only use this appliance while under supervision or instruction from an adult or carer.
• Children aged 8 and above should not clean or perform user maintenance on this appliance unless under supervision or instruction from an adult or carer.
• Do not operate any appliance with a damaged or abnormal cord or plug. If the main cord is damaged, it must be replaced by Kogan.com or a service agent on Kogan.com's behalf.
• Recharge the battery using only with the charger supplied with the appliance.
  • This appliance is intended for domestic use only.
• Do not use on wet or greasy surfaces.
• Before use, remove any objects that could entangle the brushes (long hair, plastic bags, rope, wire, etc.).
• Never immerse any part of the plug or vacuum cleaner in water or other liquids.
• Never leave the vacuum unattended while the power is one.
• Please be careful when your pet is near the vacuum cleaner.
• Do not hang the power cord over the edge of the desk or counter, or touch any sources of heat.
• It is not recommended to use any accessories other than those supplied.
  • In the event of a malfunction, stop using it immediately and contact Kogan.com.

OVERVIEW

Technical diagram of a vacuum cleaner with numbered parts for identification

1 Speed control button
2 Power indicator
3 Battery
4 Dust tank release button
5 Display

6 Metal tube release button
7 Metal tube
8 Brush release button
9 Charging port
10 Dust tank

Display

Line drawing of a handheld device with a circular dial and attached sensor port (no text or symbols)

100 V MAX VAN

Battery Level
Brush Blockage Indicator
Air-duct Blockage Indicator
Failure Indicator
Eco Speed
High Speed
Speed Control

OPERATION

1. Insert the metal tube into the nozzle and make sure it is secure (Figure 1).
2. Press the metal tube release button and remove the metal tube (Figure 2).

Line drawing of a mechanical device with no visible text or symbols

Figure 1

Technical line drawing of a mechanical device with no visible text or symbols

Figure 2

Use the different accessories according to your cleaning requirements.

1. Insert the metal aluminium tube first, then install the floor brush. Ensure the brush is secure (Figure 1).
2. The floor brush can be removed by pressing the metal tube lock (Figure 2).

Line drawing of a vacuum cleaner assembly (no text or symbols)

Figure 1

Line drawing of a vacuum cleaner with attached mechanical components (no text or symbols)

Figure 2

1. Press the power button (Figure 1), the vacuum turns on in eco speed mode.
2. Press the speed control button (Figure 2) to cycle through the different speeds.
   Note: When using, do not exceed the "maximum" dust collection capacity of the dust cup.

Technical line drawing of a mechanical device with no visible text or symbols

Figure 1

Line drawing of a vacuum cleaner device with an arrow pointing to the handle (no text or symbols present)

Figure 2

Note:

Please keep the air intake open during use to avoid clogging. Failure to do so, will cause the motor to overheat causing danger.

CHARGING

1. Turn off the vacuum and insert the charger into the charging port.
2. Plug the charger into the power outlet.
3. When charging, the blue light will flash; when the charging is finished, the light will remain on.
4. Unplug the charger, press the power switch, and the vacuum cleaner will power on.

WARNING: Only use the original charger to avoid damage to the vacuum cleaner.

CLEANING & CARE

1. In addition to the main unit, other parts can be washed with warm soapy water. After cleaning, it must be thoroughly dried before being returned for use. Never immerse the main unit in water or any liquid.
2. Clean the outer casing of the vacuum cleaner only with a soft, slightly damp cloth. Never let any liquids enter the vacuum cleaner.
3. Never use any corrosive chemicals or abrasives.
4. When the filter is damaged or worn out, it should be replaced.
5. This product contains non-removable parts and must not be disassembled or repaired by yourself.

For the best use, empty the dust bucket and clean the filter after each use.

1. Press the dust tank release button to remove the dust tank.

Technical line drawing of a mechanical device showing a disassembly process from a left-side tool to a right-side assembly (no text or symbols present)

1. Press and hold the dust tank bottom cover button below to empty the dust.

Technical line drawing of a mechanical device with two views: top shows a cylindrical component, bottom shows a motor or fan assembly (no text or symbols)

1. Separate the upper part of the dust tank from the dust tank body. Remove the filters and wash it in warm water. Ensure the filters are completely dry before reassembling.

Technical line drawings of two mechanical components, one with a curved arrow indicating motion, the other with a circular component inserted into a housing (no text or symbols present)

1. Return the filters and reassemble the dust tank. The mark on the upper part of the dust tank corresponds to the "unlock" position, ensure that the "3 small and 1 large" feet are properly inserted into the dust tank and are screwed back to the "Lock" position.

Technical line drawing of a mechanical device with two views showing internal components and directional arrows (no text or symbols)

1. Put the dust tank back on the vacuum main body.

It is recommended to replace the filter every three months (depending on the use) to ensure the best performance

SPECIFICATIONS

Voltage supply 22.2V (Li-ion 2000mAh)

Power 250W

Battery Charging time: Approx. 4 Hours

Operating time: Max 30-35mins (when the battery is full charged)

Power adapter

Input 100-240V\~, 50/60Hz 0,5A MAX

Output DC 26.5V, 0.5A

Protection Class II

Disposal

This marking indicates that this appliance should not be disposed with other house-hold wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com