KAMMTHVYSAA - Vacuum Cleaner Kogan - Free user manual and instructions

USER MANUAL KAMMTHVYSAA Kogan

Technical line drawing of a robotic arm with articulated joints and mounting base (no text or symbols)

FULL MOTION HEAVY-DUTY GAS SPRING SINGLE MONITOR MOUNT

17"-43"

KAMMTHVYSAA

SAFETY & WARNINGS

Read the entire user guide before you commence installation and assembly. If you do not understand these directions or if you have any doubts about the safety of the installation, contact a qualified technician.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

- Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact help.Kogan.com for support.

- Closely follow the assembly instructions. Improper installation may result in property damage or serious personal injury.

- Do not use this product for any purpose that is not explicitly specified in this guide.

- Do not exceed the weight capacity.

- Serious or fatal injuries can occur from tip over. To prevent tip over:

• Never allow children to climb, stand, hang or play on any part or monitor or stand.
• Use tip over restraint or anchor stand to wall.

- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe use at regular intervals (at least every three months).

75x75/100x100 43" MAX 2-15kg RATED

COMPONENTS

Technical line drawing of a mechanical linkage component (no text or symbols)

A Upper arm

Line drawing of a mechanical bracket or support structure (no text or symbols)

B Base arm

C Cable covers (x2)

D Clamp

E Monitor bracket

Simple line drawing of a 3D object resembling a lampshade or bracket (no text or symbols)

F Desk bracket

G Bracket pad

1 Thumb screw

2 Plastic pins (x4)

3 Support plate

4 Foot pad (x4)

5 Short hex screw

6 Long hex screw

7 Allen key (x2)

M-A M4x12 (x4)

M-B M4x30 (x4)

M-C M5x12 (x4)

M-D M5x30 (x4)

M-E D5 Washer (x4)

M-F Spacer (x4)

INSTALLATION

Step 1.

Attach the x4 foot pads (4) to the underside of the clamp (D).

4 D

Step 2.

Attach the bracket pad (G) to the inside face of the desk bracket (F).

F G

Step 3a: Clamp Installation

• Attach the clamp (D) to the desk bracket (F) using the short hex screw (5).
• Attach the clamp assembly to the desktop and secure it in place by tightening the screw.

7 5 D F 10-50mm

Step 3b: Support Plate Installation

• Drill a ∅10mm hole in the desktop.
• Align the support plate (3) with the drilled hole. Secure the clamp assembly in place using the short hex screw (5).

10-40mm Ø10mm 7 5 3

Step 4.

Attach the base arm (B) onto the clamp assembly and tighten the screw using the allen key (7).

Technical line drawing of a robotic arm with a base mount and labeled component B (no text or symbols beyond label)

Technical line drawing of a robotic arm with a base plate and labeled component (no text or symbols)

Step 5.

• Place the upper arm (A) onto the base arm (B).
• Tighten the screw using the Allen key (7).

Technical line drawing of a mechanical arm with labeled parts A and B (no text or symbols beyond labels)

Line drawing of a robotic arm with articulated joints and base mount (no text or symbols)

Step 6.

Attach the monitor bracket (E) to the VESA holes on the back of the monitor using the provided hardware (M-A/B/C/D) (M-E/F).

M-A/B/C/D M-E/F E

Flat Monitor

M-A M-C M-E E

Curved Monitor

M-B M-D M-E E M-F

Step 7.

Attach the monitor to the arm assembly and secure it in place using the thumb screw (1).

Technical line drawing of a mechanical arm mounted on a platform, showing front and side views (no text or symbols)

Step 8.

- Route the monitor cables up the arms and cover them using the x2 cable covers (C).

- Secure the cable covers (C) in place using the x4 plastic pins (2).

Note: Use the allen key when removing the plastic pins.

Technical diagram of a mechanical device with labeled components including 'C' and numbered parts 2

Technical line drawing of a mechanical device with an inset showing a close-up detail (no text or symbols)

Step 9.

If the monitor is not in your desired position, use the Allen key to loosen the screws as shown.

Technical line drawing of a mechanical assembly with no visible text or symbols

Note: If the display does not stop at your desired position, tighten the screws as shown.

Technical line drawing of a mechanical device with no visible text or symbols

- + - +

If the arm drops, turn the adjustment screw counter - clockwise until it stays in a horizontal position.
If the arm rises, turn the adjustment screw clockwise until it stays in a horizontal position.

CAUTION: DO NOT over tighten the screws.

NOTES

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com