FSDB24STNDB - Fitness Equipment Fortis - Free user manual and instructions

USER MANUAL FSDB24STNDB Fortis

Black metal frame with four legs and mounting brackets, no visible text or symbols

ADJUSTABLE SMARTBELL STAND

FSDB24STNDB

COMPONENTS

Exploded view diagram of a mechanical assembly with numbered parts for identification

Part	Description	Part	Description
1	Bottom cross brace	10	Nut (x20)
2	Rear left stabilizer	11	Flat washer (x36)
3	Rear right stabilizer	12	Screw 16x3 (x8)
4	Stand leg (x2)	13	Screw 16x2.75 (x4)
5	Left dumbbell platform	14	Screw 16x2.5 (x4)
6	Right dumbbell platform	15	Screw 16x1.0 (x4)
7	Towel bar	16	Casters (x4)
8	Foot pegs (x4)	17	Centre Plate
9	Straps (x2 pairs)

Hardware

3.0" Button Head 2.75" Button Head 2.5" Button Head Flat Head Lock Nut Flat Washer

Hardware Card A		Hardware Card B
QTY	Description	QTY	Description
4	2.75” Screw, button head	8	3.0” Screw, button head
4	2.5” Screw, button head	8	Lock nut
4	1.0” Screw, flat head	16	Flat washer
12	Lock nut	1	Allen key
20	Flat washer

Tools Required

Socket 9/16"

Line drawing of a mechanical tool with a cylindrical head and segmented body (no text or symbols)

Wrench 9/16"

Line drawings of two types of scissors: a flat sheet metal and a pair of scissors (no text or symbols)

Utility Knife or Scissors

ASSEMBLY

Step 1

Attach the rear left stabilizer (2) to the stand leg (4) using x2 screws (12), x2 nuts (10) and x4 flat washers (11).

Note: Do not fully tighten hardware.

Technical diagram of a mechanical linkage assembly with numbered components for identification

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Step 2

Attach the rear right stabilizer (3) to the stand leg (4) using x2 screws (12), x2 nuts (10) and x4 flat washers (11).

Note: Do not fully tighten hardware.

Technical diagram of a mechanical linkage assembly with numbered components for identification

Step 3

Attach the bottom cross brace (1) to the rear left stabilizer (2) and the rear right stabilizer (3) using x4 screws (12), x4 nuts (10) and x8 flat washers (11). Ensure the narrower edge of the cross brace (1) is closer to the stand leg (4) uprights.

Note: Do not full tighten the hardware.

Technical diagram of a mechanical linkage system with numbered components for assembly or maintenance reference.

Step 4

Install the centre plate (17) to both stand legs (4) using x4 screws (14), x4 nuts (10) and x8 flat washers (11).

Note: Ensure the centre plate edges are on the outer sides of the legs and that the logo is right side up. Tighten all hardware from steps 1-3 securely.

Technical diagram of a mechanical device with numbered components for assembly or maintenance reference.

Step 5

Secure the left dumbbell platform (5) to the assembly using x2 screws (13) using x2 nuts (10) and x4 flat washers (11).

Note: Ensure the screw holes in the platform are facing toward the inside of the stand.

Technical diagram of a robotic arm with numbered parts for identification and assembly reference.

Step 6

Secure the right dumbbell platform (5) to the assembly using x2 screws (13) using x2 nuts (10) and x4 flat washers (11).

Note: Ensure the screw holes in the platform are facing toward the inside of the stand.

Technical diagram of a mechanical assembly with numbered components, including a top view and a side-view view.

Step 7

Secure the towel bar (7) to the assembly using x4 screws (15) using x4 nuts (10) and x4 flat washers (11).

Hand tighten the screws in a cross pattern to ensure an even fit.

Note: Tighten all fasteners securely.

Technical diagram of a mechanical device with numbered components and an exploded view of the assembly

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com