DME 180 Tyxal+ - Motion detector DELTA DORE - Free user manual and instructions

USER MANUAL DME 180 Tyxal+ DELTA DORE

Outdoor motion detector

Line drawing of a rectangular cabinet or storage unit with two doors, no text or symbols present

1. Contents
   

Instructions
Important Product Informations

2. Presentation

TYXAL+ DME 180 is a passive infrared motion detector, designed to detect the infrared radiation emitted by human bodies.

This motion detector aims to protect the outside of a building by detecting intrusions prior to penetration into the premises. As soon as a presence is detected, it raises the alarm.

TYXAL+ DME 180 has an automatic system to protect it against being opened or ripped from its mount.

It is also equipped with anti-masking detection, to prevent attempts to mask the lens.

2 installation heights are possible:

- low position, between 0.8 and 1.2 m: 180° detection, 12 m range.

- high position, 2 m: 180° detection, 9 m range.

- Paired with a control unit:

- alarm signal.

- pre-alarm signal: as soon as a person enters the protected zone, an audible and visual signal (outdoor siren) warns you of the imminent alarm.

Note

This product detects temperature differences between moving and background targets within the detection zone.

If the target remains motionless, the motion detector cannot detect it. This may affect the detector's maximum detection range.

3. Location

For optimal operation, please comply with the following recommendations:

In the event of non-compliance, the product may present malfunctions or may not function optimally.

2 installation heights are possible:

- low position, between 0.8 and 1.2 m: 180° detection, 12 m range.

- high position, 2 m : 180° detection, 9 m range.

1. Location
   

Install the motion detector vertically, with its high detection zones parallel to the ground.

If the detector is installed at an angle, detection reliability may be compromised.

An integrated spirit level enables optimal installation.

Install the motion detector vertically, with both high and low detection zones parallel to the wall.

To make sure the device functions properly, attach the motion detector to the wall.

Do not direct the detector towards moving objects (leaves, bushes, flags, etc.).

Do not direct the lower detection zone towards reflecting surfaces (puddle, window, etc.).

Do not install close to a heat pump or heat evacuation outlet (dryer, etc.).

4. Mounting

Wall-mounted On a post
Use screws and dowels that are compatible with the mount.

Simple line drawing of a device with a vertical panel and diagonal lines (no text or symbols)

You can mount it onto a post using clamps (not provided).

① Unlatch the top cover to open it.

Illustration of a hand inserting a component into a device (no text or symbols visible)

② Press on the "Push" strip to separate the detector from its base.

0.8-12 m ③ Secure the base using suitable screws. The tamper is trigger bottom is broken and wall.

Do not touch the mirrors.

Do not touch the lenses.

Line drawing of a hand holding a device with a cable, no text or symbols present

Only the blue parts are actionable.

5. Activation

Hand holding a small electronic component with a magnified inset showing internal components (no text or symbols visible)

Plug the battery cable into the card connector. Set the (Tyxal+) alarm control panel to 'pending pairing', then press the pairing button on the card. Important: only the blue/green wires must be connected to the wireless car (and not the grey/yellow wires).

Hand inserting a component into a device (no text or symbols visible)

② Reposition the sensor/electronic card on the base
Attention: lock the detector part by pushing the "Push" strip until you hear a "click".

③ Close the cover

4 A 3-minute detection test launches automatically. Check that you are detected by moving into the detection zone.

⑤ With each detection, the LED flashes for 5 seconds.
Test mode automatically stops after 3 minutes and the system returns to "Normal" mode.

6. Detection zone settings

The detection zones from a to n can be easily masked by turning the masking shutter. The masking of a zone enables the prevention of false alarms.

Blue

a b c d e f g h i j k l m n

Diagram of a mechanical or electrical component with labeled parts (i-j) radiating from a central body.

Diagram of a mechanical device with labeled parts a, b, c and internal components, showing radial arrangement of dots.

Masking plate option

You have 5 masking plates to block out specidic detection zones. Example: masking of zone h.

Technical diagram showing mechanical assembly steps with labeled components and directional arrows

a b c d e f g i j k l m n n Zone h masked

7. Detector range settings for each side

Principle:

The high beam always remains parallel to the ground.

The low beam can be adjusted as shown below.

The range is limited by the angle of the low beam as the high and low beams must be intercepted simultaneously in order to activate the detector.

Diagram illustrating vehicle detection scenarios with a car, a person, and a human silhouette, showing light paths and distance markers.

If the high beam alone is cut through: No detection

If only the low beam is intercepted: No detection

The high and low beams are intercepted: Detection

Close-up of a medical device with blue surgical tabs and a white plastic casing (no visible text or symbols)

The detection distance can be easily independently adjusted between 2.5 m and 12 m, by sliding the control button on the PIR.

For example: you can select 12 m on the left and 6 m on the right to adjust the installation to suit environmental constraints.

8. Detector range settings

Low mounting

Right side 2.5 m (8 ft) 3.5 m (12 ft) 6.0 m (20 ft) 8.5 m (28 ft) 12.0 m (40 ft)

Left side 2.5 m (8 ft.) 1.0 (3) 12.0 10.0 5.0 (42) (33) (17) 3.5 m (12 ft.) 12.6 10.6 5.0 6.0 m (20 ft.) 12.6 10.6 5.0 8.5 m (28 ft.) 12.6 10.6 5.0 12.9 m (40 ft.) 12.6 10.6 5.0 (1) (2) (3) (4) (5)

-8--9-
High mounting

If the detector is installed at a height of 2 m.

In this case, the detection distance is limited to max. 9 m.

max. 9 m. 2.0 m (6°7') 3.0°7'1 10°25'1

You must perform the following steps:

① Position the cursor at L12/H9 (left side) and L40/H30 (right side).

② Reassembly the entire assembly to make the "HIGH MNT" marking appear.

Diagram illustrating a step-by-step installation or assembly process with labeled components and directional arrows

9. Function settings

Detection sensitivity settings

(L) (R) H M L

The sensitivity can be independently adjusted for each side, (L) left and (r) right, to 3 positions:

• L (low),
• M (medium),
• H (high).

The chosen position will depend on environmental conditions.

We recommend that you set the sensitivity level to H (high):

- When the detection beams were tilted horizontally.

- When higher sensitivity is required towards the end of the detection zone (12 m).

to L (low):

• When the device is installed in a mediocre location (bad conditions).
• When there is a high risk of faulty detection.

Switch settings

ON 1 2 3 4 5 6 7 8

The switches must be positioned towards the bottom during normal operation.

Switch 8: anti-masking function

• OFF position: Function inactive
  • ON position: Function active
  The masking of the lens is indicated by an Auto-Protection fault.

10. Operation with an alarm system

• Association with an alarm system
- Pre-alarm
- Selection of triggering method
- Test

Read system installation guide

II. Battery replacement

The LED flashes continuously, the battery is dead.
IMPORTANT: Before opening the unit, the alarm control unit must be in Maintenance mode (refer to system installation guide).

① Unlock the cover to open it.

Hand inserting a component into a device (no text or symbols visible)

② Press on the "Push" strip to separate the detector from its base.

1. Troubleshooting

Problem Probab e cause		Solution
The LED flashes continuously.	Incorrect power supply.	Change the battery.
Triggered detection without any objects moving	The motion detector was not installed perpendicularly to the ground.	Install the motion detector correctly.
	A reflecting object is located within the detection zone.	Eliminate all reflecting surfaces from the detection zone.
	The lower beam is longer than expected.	Check and readjust the detection beam.
	The lower detection beam is exposed to direct sun rays or to car headlights.	Readjust the detection beam so it is no longer exposed to direct light sources.
	Presence of a heat source (healing device, etc.) in the detection zone that may cause the temperature to change.	Readjust the detection beam or eliminate the heat source in the detection zone.
	An object is moving (washing hung up on a line, plants, etc.).	Readjust the detection beam or remove moving objects.
	In the event of heavy rain, water may pour through the detection zone (overflowing gutter, roof/terrace/balcony drainage, etc.)	Readjust the detection beam so it is no longer directly exposed to the flowing water.
Occasionally no detection.	Occasionally no detection.	Readjust the detection beam correctly.
	Sensitivity is set to L (low).	Readjust the sensitivity level to M (medium) or H (high).

Caractéristiques techniques / Technical characteristics / Technische Daten Caratteristiche tecniche / Características técnicas / Technische kenmerken

	2xLS 14500 - 3.6 V / 5.2 Ah - Lithium
	Consumption stand-by : 19 μAConsumption : 4 mA max / 3,6 Vcc
	[868 - 868.6] MHz and [868.7 - 869.2] MHz100 m -> 300m
	Maximum power radio < 10 mW,receiver category: 2
	-10°C / +70°C
[0.5±4]	-30°C / +60°C
IP	IP 55
[0.5±4]	95%
[0.5±4]	91,7 x 201,5 x 124,3 mm 730 gr.
Important product information (3)

CE

www.deltadore.com