EV-Y2201-AMWAQ - Security Camera Enforcer - Free user manual and instructions

USER MANUAL EV-Y2201-AMWAQ Enforcer

4-in-1 HD TVI, CVI, AHD, Analog

Vandal Dome Camera

Manual

Close-up of a white ENFORCER security camera with visible lens and control buttons (no text or symbols on the device itself)

Features:

- Select between multiple formats:

- Two-axis gimbal rotation

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Vandal Dome Camera
Specifications:

Type		Vandal Dome Camera
Formats		TVI (Default) / CVI / AHD / Analog
CMOS		^1/_2 2MP Sony CMOS
Resolution (HD)		1920x1080
TV Lines (Analog)		1200TVL
2D-NR		Yes
3D-NR		Yes
DWDR		Yes
OSD (On-Screen Display)		Yes
Cable OSD control		Yes
Video output		1.0Vp-p Complex video output
Magapixels		2MP
Lens		2.8-12mm ICR
Viewing angle		30°~50°
# of IR LEDs		24 (850nm)
IR Range		Up to 100ft (30in)
FPS		30
F Stop		F1.4-F1.6
Minimum illumination (IR On)		0Lux
Gamma correction		0-1
S/N Ratio		50dB
Gain control		Yes
White balance		Auto, Day & Night
Shutter control		Yes
Current draw	(iR On)	270mA
	(iR Off)	90mA
IP Rating		IP65
Operating voltage		12VDC
Operating temperature		-4°~131° F(-20°~55° C)
Dimensions		5 ^1/2 ×4 ^1/2 ° [132x114 mm]
Weight		1-b, 9.3-oz (717g)

Parts List:

1x Camera

4x Mounting screws

1x Security screw

1x Screwdriver

1x DC Plug with terminal block

4x Screw anchors

1x Mounting plate

1x Allen wrench

1x Manual

1x OSD Manual

Dimensions:

Adjusting the 2-Axis Gimbal:

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Vandal Dome Camera

Overview:

graph TD
    A["Cover screw"] --> B["Dome cover"]
    B --> C["Zoom/Focus compartment"]
    C --> D["Wiring notch"]
    D --> E["OSD Controller"]
    E --> F["DC Jack"]
    G["Female BNC connector"] --> E
    H["DC Plug with terminal block"] --> E

Important: Do not cut any wine as the warranty will be voided.

Zoom and Focus Adjustment:

To adjust the zoom and focus, open the Zoom/Focus compartment located in the camera body. Use the provided flathead screwdriver to loosen the zoom and focus screws to allow for adjustment.

Focus

To focus in on close objects, push the focus screw right towards 'N'. To focus out on far objects, push the screw right towards 'F'.

200m

To zoom in, push the zoom screw left towards 'T'. To zoom out, push the screw right towards "W".

OSD Controller Settings:

To set format via the OSD controller, press the controller in the direction of the desired setting, hold for 5 seconds, and release when the camera restarts. See chart below.

Before Starting:

1. Use the camera within the given temperature and voltage limits.

2. Do not point the camera at the sun. Heat can damage the camera even when not in use.

3. Do not subject the camera to strong vibrations.

4. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

Installation:

1. Undo the 4 screws on the side of the dome cover using the included alien wrench.
2. Remove the dome cover from the base
3. Temporarily connect the camera's female BNC connector to a monitor.
4. Temporarily connect the camera's DC jack to a 12VDC power supply.
5. While watching the monitor, hold the camera against the wall or ceiling by hand where it is to be mounted then adjust the camera until it is certain that the

the plate sits flush against the wall.
9. Run a hidden, permanent video cable from the monitor to the camera.
10. Run a hidden, permanent power cable from a 12VDC power supply to the camera.
11. If the installation involves surface wiring, use the wiring notch located on the side of the mounting base.
12. Reattach and secure the dome to the mounting base. 13. Test the camera again under the exact lighting conditions which it is expected to be used.

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Vandal Dome Camera

Troubleshooting:
The screen is black	Check that the camera is powered upCheck that the power supply's polarity is correctCheck that the monitor is powered upCheck that the video cable connecting the camera to the monitor is connected properly
The image is foggy or washed out at night	Check that there are no objects very close to the cameraCheck that there are no highly reflective objects in the scene
The screen image is dim	Clean the lens using a soft, clean clothCheck that the light source is adequate
The screen image has poor contrast	Adjust the monitor's contrast knobChange the position of the camera
The screen image flickers	Change the position of the camera, check cables and format setting
The screen image is distorted	Change the position of the camera, check cables and format setting
The camera case is hot	Check that the correct power supply is in use
IR LEDs do not turn on	Check that the correct power supply is in use

WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open the case of this device, as there are no user-serviceable components inside. Do not cut any wires as the warranty will be voided.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could result in the user's authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (5) years from the date of sale to the original customer. SECO-LARM's obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void it damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating property as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or proper damage of any kind to the purchaser or anyone else.