EV-Y2201-AMGQ - Security Camera Enforcer - Free user manual and instructions

USER MANUAL EV-Y2201-AMGQ Enforcer

4-in-1 HD TVI, CVI, AHD, and Analog Cameras

On-Screen Display Manual

For the following models:

Model #	Lens	Resolution	Voltage	Style	Color
EV-Y1201-A2WQ	2.8mm	1080p	12VDC	Bullet	White
EV-Y1201-AMWQ	2.8~12mm	1080p	12VDC	Bullet	White
EV-Y2201-A2WQ	2.8mm	1080p	12VDC	Rollerball	White
EV-Y2201-A2GQ	2.8mm	1080p	12VDC	Rollerball	Gray
EV-Y2201-AMWQ	2.8~12mm	1080p	12VDC	Rollerball	White
EV-Y2201-AMGQ	2.8~12mm	1080p	12VDC	Rollerball	Gray
EV-Y2201-AMWQ	2.8~12mm	1080p	12VDC	Dams	White

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Table of Contents:

Programmable Features....2

How to use the OSD Controller 3

Switching between HD Analog Outputs .... 3

Navigating the OSD....3

Menu Diagram 4-6

Lens.

Exposure 7-9

Backlight 9\~10

White Balance....11

Day & Night 12-13

Noise Reduction (NR)....13

Special 14-17

Adjust....18

Exit....19

Troubleshooting....20

Warranty 20

Programmable Features:

- Multiple Output Formats

Select between multiple different formats: AHD, CVI, TVI, and CVBS

- Exposure

Adjust the shutter speed, automatic gain control (AGC), and defog settings

• Digital Wide Dynamic Range (D-WDR)

Provide clear images even under circumstances where backlight illumination can vary

• Back Light Compensation (BLC)

Adjust the exposure to properly display the subject in front of bright light sources

- Highlight Suppression Back Light Compensation (HSBLC)

Define target areas and remove spotlights to make certain objects visible

- White Balance

Adjust the picture's color temperature/image color

• Day & Night

Adjust the level of ambient light that triggers the camera to switch between color and B/W modes

- Noise Reduction (DNR)

D-WDR OFF

D-WDR ON

BLC OFF

BLC ON

HSBLC OFF

HSBLC ON

DNR OFF

DNR ON

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

How to use the OSD Controller:

1. Press down on the joystick to open the on-screen display (OSD) menu.
2. Use the joystick to navigate the OSD menu.
3. To select an item, press down (enter) on the joystick.
4. Press down on the joystick to open the on-screen display (OSD) menu.
5. Use the joystick to navigate the OSD menu.
6. To select an item, press down (enter) on the joystick.

ENFORCE OSD Controller

Switching between HD Analog Outputs:

To set format via the OSD controller, press the controller in the direction of the desired setting, hold for 5 seconds, and release when the camera restarts. See chart below.

Direction	Format Setting
Up	CVI
Down	TVI
Left	CVBS
Right	AHD

Navigating the OSD:

1. Press down (enter) on the joystick. The Main Menu will be displayed on the monitor.
2. Move to and highlight the required function by moving the joystick up and down.
3. Select the required function by pressing enter on the joystick.

4. Change the menu setting by moving the joystick left or right.

5. After choosing the settings, move the cursor to EXIT and select the option to SAVE & END,

MAIN MENU LENS MANUAL EXPOSURE OFF BACKLIGHT WHITE BAL ATW DAY&NIGHT EXT # NR SPECIAL ADJUST EXIT SAVE&END

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD
Menu Diagram:

MAIN MENU		SETTING	SETTING OPTIONS
LENS(FASE 7)	MANUAL	SET FOR FIXED LENS CAMERAS
	DC	MODE	INDOOR
			OUTDOOR	MIN SHUTTER: 1/30MAX SHUTTER: 1/60, FLK. 1/240, 1/460, 1/1000,1/2000, 1/5000, 1/10000, 1/50000
		IRIS SPEED: 0~15
EXPOSURE(PAGES 7-9)	SHUTTER	AUTO, 1/30, 1/60, FLK. 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000, 1/50000, X2,X4, X6, X8, X10, X15, X20, X25, X30
	AGC: 0~15
	SENS-UP	OFF
		AUTO	SENS-UP: X2, X4, X6, X8, X10, X15, X20, X25, X30
	BRIGHTNESS: 1~100
	D-WDR	OFF
		ON	LEVEL: 0~8
		AUTO
	DEFOG	OFF
		AUTO	POS/SIZE: ADJUST POSITION AND SIZE OF BOX
			GRADATION: 0~2
			DEFAULT: RESET TO DEFAULT SETTINGS
BACKLIGHT(PAGES 9-10)	OFF
	BLC	LEVEL: LOW / MIDDLE / HIGH
		AREA: ADJUST POSITION AND SIZE OF BOX
		DEFAULT: RESET TO DEFAULT SETTINGS
	HSBLC	SELECT: AREA 1 / AREA 2 / AREA 3 / AREA 4
		DISPLAY	ON: ADJUST POSITION AND SIZE OF BOX
			OFF
		BLACK MASK: ON / OFF
		LEVEL: 0~100
		MODE	ALL DAY
			NIGHT	AGC LEVEL: 0~255
		DEFAULT: RESET TO DEFAULT SETTINGS
	ATW
	AWC > SET: PRESS ENTER TO SET
MAIN MENU		SETTING	SETTING OPTION
DAY&NIGHT(PAGES 12-13)	EXT	D->N (DELAY): 0~60
		N->D (DELAY): 0~60
	AUTO	D->N (AGC): 1~255
		D->N (DELAY): 0~60
		N->D (AGC): 1~255
		N->D (DELAY): 0~60
	COLOR
	B/W	BURST: OFF / ON
		IR SMART	OFF
			ON	LEVEL: 0~15
				AREA: ADJUST POSITION AND SIZE OF BOX
		IR PWM: OFF / 1~100
NR(PAGE 13)	2DNR: OFF / LOW / MIDDLE / HIGH
	3DNR: OFF / LOW / MIDDLE / HIGH
SPECIAL(PAGES 14-17)	CAM TITLE	OFF
		ON: A/D/C... 1/2/3...
	D-EFFECT	FREEZE: OFF / ON
		MIRROR: OFF / MIRROR / V-FLIP / ROTATE
		NEG. IMAGE: OFF / ON
	MOTION	OFF
		ON	SELECT: AREA 1 / AREA 2 / AREA 3 / AREA 4
			DISPLAY	ON: ADJUST POSITION AND SIZE OF BOX
				OFF
			SENSITIVITY: 0~100
			COLOR: GREEN / BLUE / WHITE / RED
			TRANS: 0.00 / 0.25 / 0.50 / 0.75 / 1.00
			ALARM	VIEW TYPE: ALL / OFF / BLOCK / OUTLINE
				OSO VIEW: ON / OFF
				ALARM OUT: ON / OFF
				TIME: 0~15
			DEFAULT: RESET TO DEFAULT SETTINGS
		OFF
			SELECT: AREA 1 / AREA 2 / AREA 3 / AREA 4
				OFF
SPECIAL(FAGES 14-17)	LANGUAGE: ENG / CHN1 / CHN2 / GER / FRA / ITA / SPA / POL / RUS / POR / NED / TUR
	DEFECT	LIVE DPC	OFF
			ON	AGC LEVEL: 0~255
				LEVEL: 0~100
		WHITE DPC	OFF
			ON	POS/SIZE: ADJUST POSITION AND SIZE OF BOX
				START: CLOSE THE IRIS THEN PRESS ENTER
				DPC VIEW: OFF / ON
				LEVEL: 0~100
				AGC: 0~14
				SENS-UP: X2, X4, X6, X8, X10, X15, X20, X25, X30
		BLACK DPC	OFF
			ON	POS/SIZE: ADJUST POSITION AND SIZE OF BOX
				START: PRESS ENTER
				DPC VIEW: OFF / ON
				LEVEL: 0~100
	RS485	CAMID: 0~255
		ID DISPLAY: OFF / ON
		BAUD RATE: 2400 / 4800 / 9600 / 19200 / 38400
ADJUST(FPAGE 15)	SHARPNESS	AUTO	LEVEL: 0~10
			START AGC: 0~255
			END AGC: 0~255
		OFF
	MONITOR	LCD	BLACK LEVEL: 0~60
			GAMMA: USER / 0.45 / 0.50 / 0.55 / 0.60 / 0.65 / 0.70 / 0.75 / 0.80 / 0.85 / 0.90 / 0.95 / 1.00
			BLUE GAIN: 0~100
			RED GAIN: 0~100
		CRT	BLACK LEVEL: 0~60
			BLUE GAIN: 0~100
			RED GAIN: 0~100
	LSC: OFF / ON

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Lens:

This function is used to select the camera's lens operation.

1. Select LENS on the Main Menu screen.
2. Select the desired Lens operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.
4. Select RETURN to return to the Main Menu screen.

- MANUAL: Select MANUAL mode for manual or fixed lens.

- DC: Select DC mode for DC Auto Iris lens. ○ MODE: Select INDOOR or OUTDOOR mode

- INDOOR: Use for indoor installations. - OUTDOOR: Use for outdoor installations. Enter menu to adjust settings.

• MIN SHUT: The minimum shutter speed is preset to 1/30.
- MAX SHUT: Set the maximum shutter speed to FLK, 1/60\~1/50000 (Default: 1/5000).

- IRIS SPEED: Set the reaction speed of the iris from 0\~15 (Default: 0).

- RETURN: Return to the Main Menu screen.

DC LENS MODE MODE INDOOR IRIS SPEED LABSOR 0 RETURN RET↓

Exposure:

This function is used to select the camera's exposure settings, including shutter speed, AGC, Sens-Up, brightness, WDR, and defog settings.

1. Select EXPOSURE on the Main Menu screen.
2. Press enter to enter the Exposure menu screen.
3. Select the desired Exposure operation by moving the joystick up or down, and select the desired setting by moving the joystick left or right and pressing enter to enter the sub-menu (if applicable).
4. Select RETURN to return to the Main Menu screen.

- SHUTTER: Set the shutter speed to AUTO, 1/30\~1/5000, x2\~x30 (Default: AUTO).

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Exposure (continued):

- SENS-UP: Activates the digital slow shutter for use in darker images.

• OFF: Turn SENS-UP off.
• AUTO: Turn SENS-UP to automatic mode Enter menu to adjust settings.

- SENS-UP: Higher values increase the brightness of the image but also potentially increase after images. Adjust from x2\~x30 (Default: x4).

- RETURN: Return to the EXPOSURE menu screen.

SENS-UP SENS-UP x4 RETURN RET

NOTE: This option is only available if SHUTTER is set to AUTO or 1/30 and if AGC is not set to 0.

- BRIGHTNESS: Adjust the camera's brightness from 0\~100 (Default: 40).

- D-WDR: Adjust the camera's digital wide

dynamic range (D-WDR) settings to provide clear images even under intense back light conditions.

• OFF: Turn D-WDR off.
• ON: Turn D-WDR on. Enter menu to adjust settings.

- LEVEL: Higher values increase the D-WDR effect. Adjust from 0\~8 (Default: 5).

- RETURN: Return to the EXPOSURE menu screen.

- AUTO: Turn D-WDR to automatic mode.

D-WDR LEVEL RETURN 5 RET

D-WDR OFF

D-WDR HIGH

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Exposure (continued):

- DEFOG: Adjust the camera's defog settings for clearer images in environments with fog or mist.

- OFF: Turn DEFOG off.

- AUTO: Turn DEFOG to automatic mode. Enter menu to adjust settings.

• POS/SIZE: Adjust the position and size of the defog mask.
• GRADATION: Higher values increase the effect of the defog mask. Adjust from 0\~2 (Default: 0).
• DEFAULT: Return the DEFOG settings to their default values.
• RETURN: Return to the EXPOSURE menu screen.

- RETURN: Return to the Main Menu screen.

DEFOG POS/SIZE GRADATION DEFAULT RETURN 0 RET

Backlight:

This function is used to control the light level to overcome strong backlight conditions.

1. Select BACKLIGHT on the Main Menu screen.
2. Select the desired Backlight operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.
4. Select RETURN to return to the Main Menu screen.

- OFF: Tum the BLC or HSBLC functions off.

- BLC: Select Back Light Compensation (BLC) to correct the exposure of the subjects that are in front of a strong backlight. Enter menu to adjust settings.

• LEVEL: Set the BLC level between LOW, MIDDLE, or HIGH (Default: MIDDLE).
  ○ AREA: Adjust the position and size of the BLC zone.
• DEFAULT: Return the BLC settings to their default values.
• RETURN: Return to the MAIN MENU screen.

BLC LEVEL MIDDLE AREA ↓ DEFAULT ↓ RETURN RET ↓

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Backlight (continued):

- HSBLC: Select Highlight Suppression Back Light Compensation (HSBLC) to improve the clarity of the picture by blocking a strong backlight. Enter menu to adjust settings.

• SELECT: Select the HSBLC area to be modified. Up to 4 areas can be used.
• DISPLAY: Tum the selected HSBLC area ON or OFF (Default: ON).
• BLACK MASK: Select whether the HSBLC areas will display a black mask or not (Default: ON).
• LEVEL: Adjust the sensitivity of the HSBLC area. Adjust from 0\~100 (Default: 70).
  ○ MODE: Select whether the HSBLC will be appear ALL DAY or only during the NIGHT (Default: ALL DAY).

- ALL DAY: The HSBLC areas are active at all times.

- NIGHT: The HSBLC areas are only active when a given AGC level is reached.

• AGC LEVEL: Higher values will block out stronger light sources. Adjust from 0\~255 (Default: 48).
  • RETURN: Return to the HSBLC menu.

- DEFAULT: Return the HSBLC settings to their default values.

- RETURN: Return to the MAIN MENU screen.

HSBLC OFF

HSBLC ON

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

White Balance:

This function is used to adjust the color temperature and image color of the picture.

1. Select WHITE BAL on the Main Menu screen.
2. Select the desired White Balance operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.

4. Select RETURN to return to the Main Menu screen.

5. ATW: Select Automatic Tracking White Balance (ATW) to automatically adjust the white balance color temperature range from 3,200°K\~9,200°K when the image color temperature changes.

6. AWC → SET: Select Automatic White balance Control (AWC) → SET to manually adjust the white balance for the current area. Point the camera towards a blank white sheet of paper and press enter to set the white balance.
7. INDOOR: Select INDOOR for general indoor applications. Use this mode for color temperature ranges from 2,800°K\~5,600°K.
8. OUTDOOR: Select OUTDOOR for general outdoor applications. Use this mode for color temperature ranges from 3,200°K\~6,400°K.

9. MANUAL: Select MANUAL to manually adjust the blue and red color temperature values for the area.

10. BLUE: Set the blue gain value. Adjust from 0\~100 (Default: 50).

11. RED: Set the red gain value. Adjust from 0\~100 (Default: 50).

- RETURN: Return to the MAIN MENU screen

- AWB: Select Auto White Balance (AWB) to automatically adjust the white balance color temperature range from 2,800°K\~6,400°K when the image color temperature changes.

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Day & Night:

This function is used to adjust the transition between color and black & white modes automatically based on the current lighting conditions.

1. Select DAY & NIGHT on the Main Menu screen.
2. Select the desired Day & Night operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.
4. Select RETURN to return to the Main Menu screen.

- EXT: Select External (EXT) mode to automatically switch between Color and B/W modes by using the integrated IR CDS sensor

• D→N (DELAY): Set the delay time for switching between day and night modes. Adjust from 0–60 (Default: 1).
• N→D (DELAY): Set the delay time for switching between night and day modes. Adjust from 0\~60 (Default: 1).
• RETURN: Return to the MAIN MENU screen.

- AUTO: Select AUTO mode to automatically switch between Color and BW modes by using AGC values set by the camera.

D→N (AGC): Set the AGC threshold for the camera. When the threshold is reached the camera will switch between day and night modes. Adjust from 1\~255 (Default: 240).
- D→N (DELAY): Set the delay time for switching between day and night modes. Adjust from 0\~60 (Default: 1).
○ N→D (AGC): Set the AGC threshold for the camera. When the threshold is reached the camera will switch between night and day modes. Adjust from 1–255 (Default: 100).
- N→D (DELAY): Set the delay time for switching between night and day modes. Adjust from 0\~60 (Default: 3).
- RETURN: Return to the MAIN MENU screen.

D&N EXT ▶D=N (DELAY) 1 N=0 (DELAY) 1 RETURN RET↓

DSN AUTO ▶D→N (AGC) —— 240 D→N (DELAY) —— 1 N→D (AGC) —— 100 N→D (DELAY) —— 3 RETURN RET ↓

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Day & Night (continued):

• COLOR: Select COLOR to force the camera to display in color mode at all times.
• B/W: Select B/W to force the camera to display in B/W mode at all times.

o BURST: Enable or disable the color burst when the camera switches from Color to
- IR SMART; The Smart IR feature adjusts the electronic shutter to adjust the IR exp

• OFF: Turn the Smart IR function off.
• ON: Turn the Smart IR function on.

LEVEL: Adjust the level of the Smart IR. Adjust from 0\~15 (Default: 1).

AREA: Adjust the position and size of the Smart IR area.

RETURN: Return to the B/W menu screen.

• IR PWM: Not used.
• RETURN: Return to the EXPOSURE menu screen.

NOTE: If DAY & NIGHT is set to B/W then WHITE BAL is not available.

Noise Reduction (NR):

This function is used to reduce the noise on the screen and allows for clearer images in lov conditions.

1. Select NR on the Main Menu screen,
2. Press enter to enter the Noise Reduction menu screen.
3. Select the desired Noise Reduction operation by moving the joystick up or down, and select the desired setting by moving the joystick left or right.

4. Select RETURN to return to the Main Menu screen.

5. 2DNR: Select the 2D Digital Noise Reduction (2DNR) for general lighting conditions. levels of DNR will decrease the noise in the image but also potentially affect the sharp Adjust from OFF\~HIGH (Default; MIDDLE).

6. 3DNR: Select the 3D Digital Noise Reduction (3DNR) for low lighting conditions. High of DNR will decrease the noise in the image but also potentially increase after images, from OFF\~HIGH (Default: MIDDLE).
7. RETURN: Return to the MAIN MENU screen.

20NR 30NR RETURN MIDDLE MIDDLE RET

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Special:

This function accesses the special features of the camera including the camera title, digital effects, motion detection, privacy masks, OSD language, and defective pixel correction (DPC).

1. Select SPECIAL on the Main Menu screen.
2. Select the desired menu operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.
4. Select RETURN to return to the Main Menu screen.

- CAM TITLE: Set the camera title to on or off.

The default camera title is the firmware

version

• OFF: Camera title off.
• ON: Camera title on. Use the joystick to select the camera title. Up to 15 alphanumeric characters can be used.

- D-EFFECT: Select to choose a digital effect to

apply to the camera.

• FREEZE: Freeze the camera image at the
  selected moment.
• MIRROR: Flip the camera image horizontally, vertically, or horizontally and vertically.
• NEG IMAGE: Invert the camera image colors
• RETURN: Return to the SPECIAL menu screen.

SPECIAL ▶ CAM TITLE ON ▼ D-EFFECT ▼ MOTION OFF PRIVACY OFF LANGUAGE ENG ▼ DETECT ▼ RS485 ▼ RETURN RET ▼

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Special (continued):

- MOTION: This function is used to detect moving objects on-screen.

• OFF: Turn motion detection off.

• ON: Turn motion detection on.

• SELECT: Select which of the four motion detection zones to modify.

• DISPLAY: Turn the selected motion detection zone on or off.

- OFF: The selected motion detection zone is turned off.

- ON: Adjust the position and size of the selected motion detection zone.

• SENSITIVITY: Adjust the sensitivity of the selected motion detection zone. Adjust from 0\~100 (Default: 64).
• COLOR: Select the color of the selected motion detection zone. Select from Green, Blue, White, and Red.
• TRANS: Set the selected motion detection zone's transparency. Adjust from 0.00\~1.00 (Default: 1.00).
• ALARM: Adjust settings for the motion detection notifications.

• VIEW TYPE: Select between different view modes for motion detection.

• OFF: Does not give any indication when motion is detected.
• BLOCK: Shows small blocks over the motion in the detection zone that is triggered.
• OUTLINE: Shows an outline around the motion in the detection zone that is triggered.

• ALL: Shows blocks and an outline of all motion detection zones when motion is detected.

• OSD VIEW: When turned on, MOTION DETECTED will display when any of the motion detection zones are triggered.
  • ALARM OUT: Not used.

• TIME: Set the amount of time that the motion detection alerts remain on the screen. Adjust from 0\~15 seconds (Default: 3).
• RETURN: Return to the MOTION menu screen.
• DEFAULT: Return the MOTION settings to their default values.
• RETURN: Return to the MAIN MENU screen.

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Special (continued):

- PRIVACY: This function is used to distort or block out certain portions of the image for privacy reasons.

• OFF: Turn the privacy feature off.

• ON: Turn the privacy feature on.

• SELECT: Select which of the four
  privacy screens to modify

• DISPLAY: Select how to display the selected privacy screen.

• OFF: Turn the selected privacy screen off.

PRIVACY SELECT AREA1 DISPLAY COLOR COLOR WHITE TRANS 1.00 DEFAULT RETURN RET

• MOSAIC: Shows the privacy screen as distorted blocks.
• INV: Shows the privacy screen as a negative image.
• COLOR: Shows the privacy screen as a solid color.
- COLOR: Select the color of the selected privacy screen. Select from White, Black.
Red, Blue, Yellow, Green, Cyan, or User (Dark Green).
- TRANS: Set the selected privacy screen's transparency. Adjust from 0.00\~1.00 (Default: 1.00).
■ DEFAULT: Return the PRIVACY settings to their default values.
- RETURN: Return to the MAIN MENU screen.

Privacy OFF

Privacy ON with Color Screen

Privacy ON with Mosaic Screen

- LANGUAGE: Set the desired OSD menu language. Select from English, Chinese (Simplified), Chinese (Traditional), German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, or Turkish.

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Special (continued):

- DEFECT: The camera can compensate for defective white or black pixels with defective pixel correction (DPC).

- LIVE DPC: The camera will automatically compensate for false white or black pixels

- OFF: Turn Live DPC off.

■ ON: Turn Live DPC on.

• AGC LEVEL: Adjust from 0\~255 (Default: 64).
  • LEVEL: Adjust from 0\~100 (Default: 100).
• RETURN: Return to the DEFECT menu.

- WHITE DPC: The camera will compensate for false white pixels.

■ OFF: Turn White DPC off
- ON: Turn White DPC on.

• POS/SIZE: Adjust the position and size of the White DPC area.
  • START: Close the iris then press enter to start.
  • DPC VIEW: Turn on to view any existing defective pixels.
• LEVEL: Adjust from 0\~100 (Default: 3).
  • AGC: Adjust from 0-14 (Default: 13).
• SENS-UP: Adjust from x2\~x30 (Default: x8).
  • RETURN: Return to the DEFECT menu.

- BLACK DPC: The camera will compensate for false black pixels.

■ OFF: Turn Black DPC off.
■ ON: Turn Black DPC on.

• POS/SIZE: Adjust the position and size of the Black DPC area.
  • START: Press enter to start.
• DPC VIEW: Turn on to view any existing defective pixels.
  • LEVEL: Adjust from 0\~100 (Default: 100).
• RETURN: Return to the DEFECT menu.

- RETURN: Return to the SPECIAL menu screen.

• RS485: Not used.
• RETURN: Return to the MAIN MENU screen.

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Adjust:

This function access video output functions such as sharpness, monitor type, and video output.

1. Select ADJUST on the Main Menu screen.
2. Select the desired menu operation by moving the joystick to the left or right and pressing enter to enter the sub-menu (if applicable).
3. Use the joystick to adjust the settings.
4. Select RETURN to return to the Main Menu screen.

- SHARPNESS: Adjust the sharpness of the image.

• OFF: No sharpness adjustment.

• AUTO: Adjust the level at which the sharpness adjustments will take place.

• LEVEL: Higher values will result in a sharper image. Adjust from 0\~10 (Default: 6).

• START AGC: Select the AGC value where the sharpness adjustments will start. Adjust from 0\~255 (Default:

120).

• END AGC: Select the AGC value where the sharpness adjustment will end. Adjust from 0\~255 (Default: 255).
• RETURN: Return to the ADJUST menu screen.

- MONITOR: Adjust the camera's image according to the type of monitor being used.

- LCD: Select for LCD monitors

• BLACK LEVEL: Adjust the black level of the image. Adjust from 0\~60 (Default: 58).
• GAMMA: Adjust the gamma level of the image. Adjust from USER, 0.45\~1.00
  (Default: USER).
• BLUE GAIN: Adjust the blue gain of the image. Adjust from 0\~100 (Default: 50).
• RED GAIN: Adjust the red gain of the image. Adjust from 0\~100 (Default: 50).
• RETURN: Return to the ADJUST menu screen.

o CRT: Select for CRT monitors.

• BLACK LEVEL: Adjust the black level of the image. Adjust from 0\~60 (Default: 58).
• BLUE GAIN: Adjust the blue gain of the image. Adjust from 0–100 (Default: 50).
• RED GAIN: Adjust the red gain of the image. Adjust from 0\~100 (Default: 50).
• RETURN: Return to the ADJUST menu screen.

- LSC: Lens Shading Correction (LSC) adjust the shading of the outside of the image.

ADJUST SHARPNESS AUTO MONITOR LCD LSC OFF VIDEO OUT NTSC COMET OFF RETURN RET

Exit:

This function is used to save all OSD changes and exit the menu screen, reset all values to their factory defaults, or exit the menu screen without saving any changes.

1. Select EXIT on the Main Menu screen.
2. Select the desired operation by moving the joystick to the left or right and pressing enter.
3. SAVE & END: Save all OSD changes and exit the OSD menu.
4. RESET: Restore all OSD settings to factory defaults and exit the OSD menu.
5. NOT SAVE: Exit the OSD menu without saving any changes

ENFORCER 4-in-1 HD Cameras (TVI, CVI, AHD, Analog) OSD

Troubleshooting:
The screen is blank.	Check that the camera is powered up.Check that the power supply's polarity is correct.Check that the monitor is powered up.Check that the video cable connecting the camerato the monitor is connected properly.
The screen image is dim.	Clean the lens using a soft, clean cloth.Check that the light source is adequate.
Strong backlight is overpowering the image.	Change the D-WDR or Backlight settings.
Image has too much digital noise.	Change the DNR settings.
The screen image is distorted.	Change the position of the camera.
Motion detection is not activated.	Activate MOTION DET in the Setup Menu.Properly define the motion detection area.
IR LEDs do not turn on.	Check that the correct power supply is in use.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM's obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.