DS-PAN-903 - Docking Station Havis - Free user manual and instructions

USER MANUAL DS-PAN-903 Havis

Havis Docking Station

For Panasonic Toughpads FZ-M1 & FZ-B2

DS-PAN-900 Series

DS-PAN-901

DS-PAN-905

DS-PAN-901-2

DS-PAN-905-

3D CAD model of a mechanical housing component with orange internal components and mounting holes (no text or symbols visible)

Havis, Inc.

Before Beginning

(Original Instructions)

Havis is pleased to provide this Owner's Manual to aid in the proper installation and use of the DS-PAN-900 Series Docking Station for the Panasonic Toughpads FZ-M1 and FZ-B2.

For questions regarding the set-up of your DS-PAN-900 Series Docking Station, please contact Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.

This Owner's Manual applies to the following Part Numbers:

* Toughpad FZ B2 is only compatible with DS PAN 903, DS PAN 905, DS PAN 905 2, DS PAN 906, & DS PAN 906-2 Docking Stations

WARNING

- NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.

• DO NOT USE COMPUTER WHILE DRIVING.

CAUTION

• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
• ONLY TABLETS WITH RF PASS-THRU WILL LATCH INTO DOCKING STATIONS EQUIPPED WITH AN ANTENNA MODULE (DS-PAN-901-2, DS-PAN-902-2, DS-PAN-905-2, and DS-PAN-906-2). ATTEMPTING TO LATCH A TABLET WITH NON-RF PASS-THRU MAY RESULT IN DAMAGE TO THE TABLET AND/OR DOCKING STATION.
  FOR THE DS-PAN-901, DS-PAN-901-2, DS-PAN-902, DS-PAN-902-2, DS-PAN-905, DS-PAN-905-2, DS-PAN-906 AND DS-PAN-906-2 DOCKING STATIONS: DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: This product requires a certified, automotive grade, Panasonic approved 24W power source rated for a continuous, 12VDC output (Havis Part Number LPS-102 or equivalent). Failure to comply with this requirement will cause product damage that is NOT repairable and is NOT covered under warranty.
  FOR THE DS-PAN-903 DOCKING STATION: DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: The Panasonic FZ-M1 & FZ-B2 tablets require a certified, Panasonic approved power source rated for a continuous, regulated 16VDC output. Failure to comply with this requirement will cause product damage that is NOT repairable and is NOT covered under warranty.

NOTICE

• FOR DOCKING STATION MODELS EQUIPPED WITH A RUNDLED POWER SUPPLY

Related Products

Havis offers a wide variety of accessory products specifically for use with the DS-PAN-900 Series Docking Station. For more information or to order, please visit www.havis.com.

DS-DA-218

Desktop Stand for Tablet Docking Stations

Durable stand for mounting tablet Docking Stations for use in the home or office.

LPS-102

90W Power Supply

External in-vehicle power supply and cable for Panasonic Toughpads FZ-M1 & FZ-B2 with cigarette lighter adaptor.

DS-DA-501

Replacement Keys

Set of two (2) replacement keys for DS-PAN-900 Series Docking Stations.

DS-DA-602

Rugged Communications Hub

Rugged USB/Ethernet hub makes adding peripherals to your mobile workspace easy and safe.

Operation - Docking (continued)

4) For theft deterrence, secure tablet by locking Docking Station with supplied key (Hardware Kit Item 2).

Technical diagram of a mechanical component with labeled parts (no readable text or symbols)

Operation - Undocking

1) If previously locked, unlock Docking Station using supplied key.
2) While holding tablet with one hand, lift the Latch Handle on the top of Docking Station.

3) Once unlatched grab both sides of tablet, rock the top forward and carefully lift out of Docking Station, top end first.

Table of Contents

Specifications 3

Parts Included 4

Port Replication Capability 5

Antenna Identification 5

Installation 6

Cable Management 7

Operation - Docking 8

Operation - Undoing 10

Precautions

• Do not place metal objects or containers of liquid on top of the Docking Station
• If a malfunction occurs, immediately unplug the Power Supply and remove the tablet
• Use only the specified Power Supply (Part # LPS-102) with this Docking Station
• Do not store the Docking Station where water, moisture, steam, dust, etc. are present.
• Do not convert cables into parts other than what they are specified for
• Do not leave the Docking Station in a high temperature environment (greater than 60°C, 140°F)
  for a long period of time
• Do not connect cables to the DC Power Port or Ethernet Port exceeding 3 meters in length.

Specifications

Power Supply Input 12.0 V DC-in
Dimensions 7.9" (20.1 cm) H x 8.6" (21.8 cm) W x 3.0" (7.6 cm) D
Weight 1.6 lbs (0.73 kg)
Operating Environment -10°C to 50°C (14°F to 122°F)
Storage Environment -40°C to 85°C (-40°F to 185°F)

EC DECLARATION OF CONFORMITY in accordance with EN 45014

Manufacturers Name: Havis, Inc.

Manufacturers Address: 47891 Anchor Court, Plymouth Twp, MI 48170 USA

Declares under our sole responsibility that the product

Moduli Name: Resin Docking Station For Panavonite Toupipani F2 M1 K F2 B2 Mode: DS PAN 80% where X may be any alphabet made character and which describes product output

LIS PAV SUK, where X is by any alphanumeric character and which describes it. May be followed by any alpha-numeric characters which describe product options

Product Options: This declaration covers all options of the above product which hear the CF Marking.

Is in conformity with the following standards or other normative documents:

LMC Directive 2004/108/LC: LN 55022:2010, Class B, Information technology equipment

GASO DISCUITABLE CHARACTERIES - FLIMICS AND PROCESSES IN PROCESITION

LN 55024.2010, Information technology equipment - Immunity characteristics

limits and methods of measurement

Niracima 2013 (26/11) Particles of the one of four times horizons in the course (2014)

Docking Station Latch Handle Barrel Lock Latch Tab Docking Connector Alignment Posts (hidden from view in this illustration) Ground Pins Mounting Holes (x4) (9-5A 75mm hole pattern) Ports Strain Relief Anchor Points Hardware Kit This Hardware Kit includes: 1. Zip Ties (6) 2. Keys (2) 3. M4 x 0.7 x 12mm long

Operation - DockingParts Included

2) Hold tablet in landscape orientation, with bottom angled toward the Docking Station. Lower tablet into the bottom of the Docking Station while ensuring that the alignment sockets are aligned with the Docking Station's Alignment Posts.

3D mechanical component diagram with orange arrow indicating direction (no text or symbols)

3) Pivot tablet into the Docking Station and lower the Latch Handle to secure tablet in place.

NOTICE If there is excessive force while lowering the Latch Handle, check orientation and position of tablet

Operation - Docking

CAUTION

TO ENSURE A PROPER CONNECTION, PLEASE READ THE FOLLOWING BEFORE DOCKING YOUR TABLET.

DO NOT FORCE TABLET ONTO DOCKING STATION.

IF THERE IS RESISTANCE, CHECK THAT YOUR

TABLET IS CORRECTLY CONFIGURED FOR THE DOCKING STATION

ONLY TABLETS WITH RF PASS-THRU WILL LATCH INTO DOCKING

STATIONS EQUIPPED WITH AN ANTENNA MODULE

ATTEMPTING TO LATCH A TABLET WITH NON-RF PASS-THRU MAY RESULT IN DAMAGE TO THE TABLET AND/OR DOCKING STATION.

Technical diagram showing a mechanical component with a highlighted section and an arrow indicating direction, labeled 'M1.03'.

Example of a Docking Station equipped with an Antenna Module.

Diagram of a device rear panel with an orange arrow pointing to a component (no text or symbols present)

Example of a Tablet without RF Pass-Thru. DO NOT attempt to latch onto a Docking Station equipped with an Antenna Module

1) Ensure Docking Station is unlatched by lifting Latch Handle.

Port Replication Capability

Full Port Replication for use with Toughpad FZ-M1

(DS PAN 901, DS PAN 901 2, DS PAN 902, DS PAN 902 2)

Antenna Selection Switches Power Input USB 3.0 (HZ) SS Ethernet (K145) HDMI HOMI VGA Serial Antennas (25+44A+82-2) USB HMI+902-2 (40+60+60)

Lite Port Replication for use with Toughpads FZ-M1 & FZ-B2

Internal/External Antenna Selection switches Power Input USB 3.0 (5.2) SS Ethernet (RJ45) Antennas DS-PAW-956.2 DS-PAW-956.2 (operable)

Antenna Identification (DS-PAN-901-2, DS-PAN-902-2, DS-PAN-905-2, DS-PAN-906-2)

In reference to the Panasonic FZ-M1 Antenna connections

ANT A = Lower

ANT B = Upper

Downward Facing Antennas Tablet Interface

Installation

1) Align Docking Station mounting holes with the holes on VESA 75mm hole pattern device. Using the four (4) M4 x 0.7x12mm Pan Head Screws (Hardware Kit Item 3), four (4) Washers, M4 (Hardware Kit Item 4), and four (4) Lock Washers, M4 (Hardware Kit Item 5), secure the Docking Station to device. Torque screws to 20 in-lbs (2.3Nm) ± 10%.

A) Havis Desktop Stand installation (sold separately, Part # DS-DA-218).

Washer, M4 Lock Washer, M4 M4 x 0.7x12mm Pan Head Screws Desktop Stand (VESA 75 mm)

B) In-Vehicle mounting system installation.

Washer, M4 Lock Washer, M4 M4 x 0.7x12mm Pan Head Screws

Cable Management

1) Tip the Docking Station to a position that is comfortable to work with.
2) Connect all cables that are necessary for computing needs.
3) Use Zip Ties (Hardware Kit Item 1) to strain relieve cables. Strain Relief Points are located on the bottom and sides of Docking Station and should be used to anchor each cable.

Diagram of a device rear panel with labeled components and orange annotations highlighting features

4) Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion.
5) Tie off cables onto a stationary part of the mounting system.

This loop must be large enough to allow full range of expected rotation and extension without stressing connections. Collect cables and secure to the mounting system. (Note: Mounting system not included)

This loop must be large enough to allow full range of expected rotation and extension without stressing connections.