GS-1008PL - Network switch Edimax - Free user manual and instructions

USER MANUAL GS-1008PL Edimax

No.3, Wu-Chuan 3rd Road, Wu-Gu, New Taipei City 24891, Taiwan

Email: [e-mail]

Edimax Technology Europe B.V.

Fijenhof 2, 5652 AE Eindhoven, The Netherlands

Email: [e-mail]

Edimax Computer Company

3350 Scott Blvd., Bldg.15 Santa Clara, CA 95054, USA

Live Tech Support: 1(800) 652-6776

Email: [e-mail]

COPYRIGHT

Copyright © Edimax Technology Co., Ltd. all rights reserved. No part of this publicaon may be reproduced, transmied, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnec, opcal, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.

Edimax Technology Co., Ltd. makes no representaons or warranes, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranes, merchantability, or tness for any parcular purpose. Any soware described in this manual is sold or licensed as is. Should the programs prove defecve following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the enre cost of all necessary servicing, repair, and any incidental or consequential damages resuling from any defect in the soware. Edimax Technology Co., Ltd. reserves the right to revise this publicaon and to make changes from me to me in the contents hereof without the obligaon to nofy any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly dierent from those shown in this QIG. The specicaon is subject to change without noce. Please visit our web site www.edimax.com for the update. All brand and product names menoned in this manual are trademarks and/or registered trademarks of their respective holders.

Edimax Technology Co., Ltd.

Add: No. 3, Wu-Chuan 3rd Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan

PRODUCT INTRODUCTION

Model no.:

ES-1008PL: 8-Port Fast Ethernet PoE+ Switch

GS-1008PL: 8-Port Gigabit Ethernet PoE+ Switch

Package Contents

Before you start using this router, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s):

• PoE switch x 1pcs
• Quick installaon guide x 1pcs
  ● Power cord x 1pcs
  ● Rubber feet x 4pcs
  ● Rack-mount brackets and screws x 1 set

Safety Precauons

To avoid any device damage and bodily injury caused by improper use, please observe the following rules.

*Keep the power o during the installaon.
*Wear an ESD-prevenve wrist strap, and make sure that the wrist strap has a good skin contact and is well grounded.
*Use only the power cord provided with the Switch.
*Make sure that the supply voltage matches the specicaons indicated on the rear panel of the Switch.
*Ensure the vent hole is well venlated and unblocked.
*Do not open or remove the cover of the Switch.
*Before cleaning the device, cut o the power supply. Do not clean it by the waterish cloth, and never use any other liquid cleaning method.

Front Panel

Please refer to the following descripon for the front panel:

*ES-1008PL

ES-1008PL Fast Ethernet PoE+Switch LINK/ACT PoE 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

*GS-1008PL

ESIMAX GS-1008PL Gigabit Ethernet PoE+Switch LINK/ACT 1 2 3 4 5 6 7 8 Gigabit PoE 1 2 3 4 5 6 7 8

LED Denions:

LED Name	Light Status	Descripon
PWR	On	Switch on and correctly powered
	O	Switch not powered or not correctly powered
LINK/ACT	On	The port connected
	O	The port not connected
	Flashing	The port is acvang and transferring /receiving data.
Gigabit (GS-1008PL)	On	There is a 1000Mbps device connected to the corresponding port.
	O	There is a 10/100Mbps device connected to the corresponding port, or there is no device connected to the corresponding port.
PoE	On	There is a PoE PD connected to the port, which supply power successfully.
	O	No PD is connected to the corresponding port, or no power is supplied according to the power limits of the port.

Back Panel:

AC LINE 100-240 VAC 50/60 Hz

Power Connector:

Plug in the female connector of the provided power cord into this AC LINE socket, and the male into a power outlet. Supported input voltages range from 100-240V AC, and 50-60 Hz.

Product Specicaons:

Model		ES-1008PL	GS-1008PL
Standards		IEEE 802.3 10BaseTIEEE 802.3u 100BaseTXIEEE 802.3af/802.3at PoEEEEE 802.3x Flow ControlIEEE 802.3az Energy EcientEthernet	IEEE 802.3 10BaseTIEEE 802.3u 100BaseTXIEEE 802.3ab 1000BaseTIEEE 802.3af/802.3at PoEEEEE 802.3x Flow ControlIEEE 802.3az Energy EcientEthernet
Interface	RJ-45	8 ports	8 ports
	PoE	8 ports	8 ports
MAC Address		1K	8K
Buer Memory		96KB	128KB
Jumbo Frames		N/A	9K
Total Power budget		80W
Power Consumpon		5 Was (Max. no PD connected)
Dimensions		280 x 179 x 44.5 (L x W x H)
Weight		1.5 kg
Operang		0 to 40°C
Storage Temperature		-40 to 70°C
Humidity		Operang:10 to 90% RH (non-condensing)

Note:

* PoE budget: Up to 30 Was max per port, 75 Was Total
* Please ensure you do not exceed the PoE power budget and overload the PoE switch.

For example:

	7.7W	15.4W	30W
Max. PoE ports (up to)	8 ports	4 ports	2 ports

* Make sure the PDs that you connected to the Switch are compliant with IEEE802.3af/IEEE802.3at standard.

1. PRODUCT INSTALLATION

There are two ways to install your switch, please select one that suits you.

2. Desktop Installaon

1. Install the switch on a level surface that can support the weight of the unit and the relevant components, and each the rubber feet to the boom. The rubber feet cushion the switch and helps protect the case from scratches.

2. Plug the switch into an electrical source with the provided power cord.

3. Rack-Mount Installaon

Rack moung allows for a more orderly installaon when a series of network devices is being installed.

1. Disconnect all the cables from the switch.
2. Place the unit the right way up on a hard, at surface with the front facing you.
3. Posion a moung bracket over the moung holes on one side of the unit.
4. Insert the screws and fully ghten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
6. Insert the unit into the rack and secure with suitable screws
7. Reconnect all the cables.

Regarding the installaon environment, we strongly recommend:

1. The switch should be placed in an appropriately venlaon environment. A minimum 25 mm space around the unit is recommended.
2. The switch and the relevant components should be kept away from sources of electrical noise such as radios, transmiers and broadband amplifiers.
3. Avoid environments with higher than recommended moisture levels.

Troubleshoong

1. Power LED is not lit

Check if the power cord is properly connected to the plug and the power outlet; make sure the power cord is rmly plugged into the power socket of the switch.

2. LINK/ACT LED is not lit when connected to devices

● Make sure the network device aached to the switch is turned on.
● Make sure the network cable is properly connected to the switch and the network device.
● Make sure the network cable is a UTP cable that complies with EIA/TIA 568 and Category 5 specicaons.

[!] Contact your dealer if problem persist.

Appendix: The standard RJ-45 Introducon

RJ45 Pin:

Below is an indication of a standard RJ-45 socket and plug, and denion for the pins.

1 2 3 4 5 6 7 8

Isometric view of a rectangular electronic component with numbered pins (8 to 1) and internal slot, no text or symbols present.

RJ-45 Connector pin signal:

RJ-45 Connector pin signal
Pin no.	MDI-II signal	MDI-X signal
1	TX+	RX+
2	TX-	RX-
3	RX+	TX+
4	POE -	POE -
5	POE -	POE -
6	RX-	TX-
7	POE +	POE +
8	POE +	POE +

The following shows straight cable and crossover cable conncon, ordinary please use straight cable to connect switch/Hub or other devices:

Straight cable for the switch (uplink MDI-II port) to switch/Hub or other devices conncon

graph LR
    subgraph MDI-II
        A1["Input"] --> A2["1 TX+"]
        A2 --> A3["2 TX-"]
        A3 --> A4["3 RX+"]
        A4 --> A5["6 RX-"]
    end
    subgraph MDI-X
        B1["Input"] --> B2["TX+ 1"]
        B2 --> B3["TX- 2"]
        B3 --> B4["RX+ 3"]
        B4 --> B5["RX- 6"]
    end
    A1 --> A4
    A2 --> A4
    A3 --> A4
    A4 --> A5
    B1 --> B4
    B2 --> B5
    B3 --> B5
    B4 --> B5
    B5 --> B6["Output"]

Cross over cable for switch (MDI-X port) to switch/hub or other network devices (MDI-X port) conncon.

graph LR
    subgraph MDI-X
        A1["Input"] --> B1["1 RX+"]
        A2["Input"] --> B2["2 RX-"]
        A3["Input"] --> B3["3 TX+"]
        A4["Input"] --> B4["6 TX-"]
    end
    subgraph MDI-X
        C1["Input"] --> D1["RX+ 1"]
        C2["Input"] --> D2["RX- 2"]
        C3["Input"] --> D3["TX+ 3"]
        C4["Input"] --> D4["TX- 6"]
    end
    A1 --> B1
    A2 --> B2
    A3 --> B3
    A4 --> B4
    C1 --> D1
    C2 --> D2
    C3 --> D3
    C4 --> D4
    D1 --> M1["Output"]
    D2 --> M2["Output"]
    D3 --> M3["Output"]
    D4 --> M4["Output"]

Federal Communicaon Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residential installaon. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons.

However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separaon between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

FCC Cauon

This device and its antenna must not be co-located or operang in conjunction with any other antenna or transmier.

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.

Any changes or modicaons not expressly approved by the party responsible for compliance could void the authority to operate equipment.

CE Mark Warning

This is a class B product. In a domesc environment this product may cause radio interference in which case the user may be required to take adequate measures.

EU Declaraon of Conformity

English:	This equipment is in compliance with the essenal requirements and other relevant provisions of Direcve 2004/108/EC and 2006/95/EC
Français:	Cet équipement est conforme aux exigences essenelles et autres disposions de la direcve 2004/108/EC and 2006/95/EC
Češna:	Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2004/108/EC and 2006/95/EC
Polski:	Niniejszym (Edimax) oświadcza, že (ES-3305P / ES-3308P/ ES-3116P) jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami dyrektywy 2004/108/EC and 2006/95/EC
Română:	Acest echipament este în conformitate cu cerințele esențiale și alte prevederi relevante ale Direcvei 2004/108/EC and 2006/95/EC
Русский:	Это оборудование соответствует основным требованиям и положениям Директивы 2004/108/EC and 2006/95/EC
Magyar:	Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek (2004/108/EC and 2006/95/EC)
Türkçe:	Bu cihaz 2004/108/EC & 2006/95/EC direkeri zorunlu istekler ve diğer hükümlerle ile uyumludur.
Українська:	Обладнання відповідає вимогам і умовам директиви 2004/108/EC and 2006/95/EC /108/EC
Slovenčina:	Toto zariadenie spĺňa základné požiadavky a d’alšie príslušné ustanovenia smerníc 2004/108/EC and 2006/95/EC
Deutsch:	Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2004/108/EC and 2006/95/EC
Español:	El presente equipo cumple los requisitos esenciales de la Direcva 2004/108/EC and 2006/95/EC
Italiano:	Questo apparecchio è conforme ai requisi essenziali e alle altre disposizioni applicabili della Direva 2004/108/EC and 2006/95/EC
Nederlands:	Dit apparaat voldoet aan de essenële eisen en andere van toepassing zijnde bepalingen van richtlijn 2004/108/EC and 2006/95/EC
Português:	Este equipamento cumpre os requesitos essênciais da Direcva 2004/108/EC and 2006/95/EC
Norsk:	Dee utstyret er i samsvar med de vikgste kravene og andre relevante regler i Direkv 2004/108/EC and 2006/95/EC
Svenska:	Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta bestämmelser i direkv 2004/108/EC and 2006/95/EC
Dansk:	Dee udstyr er i overensstemmelse med de væ sentligste krav og andre relevante forordninger i direkv 2004/108/EC and 2006/95/EC
Suomi:	Tämä laite täyää direkivien 2004/108/EY &2006/95/EC oleelliset vaamukset ja muut asiaankuuluvat määräykset.

FOR USE IN

DE GR HU IE IT LV LT LU MT NL PL PT UA SK SI ES SE GB IS LI NO CH BG RO TR

АЯ46

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collecon point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.

Declaraon of Conformity

We, Edimax Technology Co., LTD., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Council directive (2004/108/EC and 2006/95/EC).

Equipment : 8-Port Fast / Gigabit PoE+ Switch

Model No. : ES-1008PL / GS-1008PL

The following European standards for essenal requirements have been followed:

EMC : EN 55022:2010

EN 55024:2010

EN 61000-3-2:2006 + A2:2009

EN 61000-3-3:2008

Safety (LVD): EN 60950-1 :

2006+A11:2009+A1:2010+A12:2011

Edimax Technology Co., Ltd.

No. 3, Wu Chuan 3 ^rd Road,

Wu-Ku Industrial Park,

New Taipei City, Taiwan

CE

Date of Signature: July, 2014

Signature:

Printed Name:

Albert Chang

Title:

Director

Edimax Technology Co., Ltd.

ΣDIMAX

NETWORKING PEOPLE TOGETHER