Kelly - Bed Fantastic - Free user manual and instructions

USER MANUAL Kelly Fantastic

Assembly Instructions

KELLY

BUNK

Isometric line drawing of a multi-tiered metal shelving unit (no text or symbols)

2 PEOPLE REQUIRED

Ver1.2

FANTASTIC FURNITURE

WARNING

FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE THAT IS NOT COVERED BY YOUR WARRANTY

1

Instructions !. Read Me

Read Instructions carefully. Check no parts are missing.

2

Illustration of a person sitting on the floor assembling or packing sheets of rectangular blocks (no text or symbols)

Lay out all of the components on a soft surface as if you were preparing to do a jigsaw puzzle.

3

LEFT RIGHT

Carefully identify each component, especially those that are similar. The most common mistake is getting things back to front.

4

Illustration of a person holding a smartphone and a screwdriver (no text or symbols)

Separate and identify each component from the hardware pack and rest each one in its proper location before fastening.

5

ng things back to front. DO NOT USE

DO NOT fully tighten screws (leave slightly loose). When the item is fully assembled tighten the screws - but do not over tighten.

6

Line drawing of a person sitting on a chair facing away from a wall, no text or symbols present

If glue is required DO NOT set until you are certain that the parts belong together.

What you Need

To Assemble the Body

DO NOT USE

(Tools not provided) Mallet 2x Slats (P8) Top Post (P3) 2x Top End Panel (P1) Top Post (P2) Back Guard (P7) Front Guard (P6) Lower Post (P11) Lower Post (P10) Top Post (P4) 4x Mid Post (P9) Side Rail (P16) Top Post (P5) Lower Post (P13) Side Rail (P15) Ladder (P17) Lower Post (P14) 2x Base End Panel (P12)

28x Bolts
(M6x15mm)
(H1)

4x Bolts
(M6x35mm)
(H2)

7x Bolts
(M6x65mm)
(H3)

4x Sleeve Nut
(M6x15mm)
(H4)

5x Small Endcap
(H5)

4x Top Endcap
plus 4x Extra Top Endcap
(H6) (H7)

4x Foot Endcap
plus 4x Extra foot Endcap

M4-Allen key

Step 1

Assemble the top bed

Step 1 You will need: 8x Bolts M6 x 15mm (H1) 4x Top Endcap (H6) M4-Allen key provided (H6) (H1) (H6) (H1) (H1) (P3) (P2) (P1) (P4) (P1) (P5) (P5)

Attach Top Post (P2 & P3) to Top End Panel (P1) using 4x Bolts (H1). Insert 2x Top Endcap (H6) into each Top Post. Repeat same for the other top bed end assembly as shown.

Step 2

You will need:
8x BoltsM6 x 15mm(H1)
3x BoltsM6 x 65mm(H3)
1x Small Endcap(H5)

2 PEOPLE REQUIRED

M4-Allen key provided (H3) (H1) (H1) (P7) (H3) (P6) (H1) (H1) (H5)

Attach the Front Guard (P6) to the Top Posts with 4x Bolts (H1) and 1x Bolt (H3), attach Back Guard (P7) with 4x Bolts (H1) and 2x Bolts (H3). Insert 1x Small Endcap (H5) as shown.

Step 3

Step 3 (Tools not provided) Mallet (P8) Attach the Slats (P8). Some effort is required to pull each slat into position as the centre strap is designed to keep the slats tight.

Well done. You have assembled the top bed, and now we will assemble the bottom bed.

Step 4

You will need: 4x Bolts M6 x 15mm (H1) 4x Bolts M6 x 65mm (H3) 4x Foot Endcap (H7) (M4-Allen key provided) (P9) (P9) (H3) (H1) (P11) (H7) (P12) (P13) (P12) (P9) (P9) (H3) (H1) (P10) (H7) (P14) (H7)

Insert Mid Posts (P9) into Lower Posts (P10 & P11), then attach these to Base End Panel (P12) using 2x Bolts (H1) and 2x Bolts (H3). Insert 2x Foot Endcap (H7) into each Lower Post. Repeat same for the other base end as shown.

Step 5

You will need:
8x BoltsM6 x 15mm(H1)

M4-Allen key provided (H1) (H1) (P16) (P15) (H1) (H1) note:holes for ladder 2 PEOPLE REQUIRED

(H1) (H1) (P16) (P15) (H1) (H1) note:holes for ladder

Attach the Side Rails (P15 & P16) to the end assembles using 8x Bolts (H1).

Step 6

(Tools not provided) Mallet

Step 6 (Tools not provided) Mallet (P8)

Attach the Slats (P8). Some effort is required to pull each slat into position as the centre strap is designed to keep the slats tight.

Well done. You have assembled the bottom bed. The two beds will now be put together to form the bunk bed.

note: In the future if you require two single beds, the bunk can be disassembled. Remember to remove the mid posts from the bottom bed and insert the spare end caps.

Step 7

2 PEOPLE REQUIRED

Technical diagram of a two-tiered metal bunk bed with structural details and mounting points, showing structural changes and component placement.

Two people carefully lift the top bed into position. Note location of holes for ladder.

Step 8

You will need:
4x BoltsM6 x 35mm(H2)
4x Sleeve NutM6 x 15mm(H4)
4x Small Endcap(H5)	[kC32]

M4-Allen key provided

(H5)

Technical diagram of a two-tiered modular shelving unit with labeled components (H2, H4, H5) and structural details.

Fit 4x Endcap (H5) to the Ladder (P17), then attach ladder to the bunk using 4x Bolts (H2) and 4x Sleeve Nuts (H4).

The job is now complete!

In the interest of our environment Please dispose of all packaging thoughtfully.