MBQ-STG2-BT - Pregnant MB QUART - Free user manual and instructions

USER MANUAL MBQ-STG2-BT MB QUART

UTV & RZR Tuned Audio Systems

Close-up of a black industrial fan or vent with circular perforated grille and mounting holes (no visible text or symbols)

Close-up of a black industrial fan or vent with radial slots and central perforated grille (no visible text or symbols)

MBQ-POD

8 Inch Compression Horns

MB QUART RZR Kick Panel pods

Thanks for choosing MB QUART. These 8 inch compression horn speaker components have been meticulously engineered to install into your Polaris RZR. They are part of our Staged RZR Tuned Audio Systems family of products. See all the components, upgrades and Stages available for RZR on the website MBQUART.com

We have made the install process so simple, you will be in and out of the machine in about an hour.

IMPORTANT – Before you mount the speakers into the pods and mount the pods to the RZR, you need to prepare the rear of the compression horn speakers. This entails removing the back plate from each speaker and covering the exposed compression horn diaphragm with the included cover.

The purpose of this process is to remove some of the depth of the speaker which in turn reduces the amount of space you sacrifice in the foot well – brilliant.

IN THE BOX

• 8 inch speakers (2)
  • RZR Kick Panel pods (2)
  • Compressions Horn Diaphragm covers (2)
• Mounting Hardware (4 bolts, 4 nylon locking nuts, 8 washers)
  • Stainless Speaker Mounting screws (8)

SAFETY

Always make your machine safe before installing any accessories

• Turn the ignition off and remove the key
• Remove the negative terminal of the battery
• Safety Glasses - always wear eye protection

TIME & TOOLS

You will need to prepare the Compression Horns before permanently mounting them to the pods. To keep installation quick it is best to mount the pods empty with no speakers installed. This will keep install to about 1 HOUR.

MBQUARTI® MUSIC. DEFINED.

TOOLS Required

• T-40 Torx Bit Driver
- Sharpie or Marker
- Painters Tape 2 inch
- 1/2 inch Socket
• #2 Philips Screw Driver
• 1/2 inch open wrench
- Small or Angled Ratchet
- Work light
- Drill
- 1/8 inch drill bit
- 5/16 inch drill bit

NH1-120B Preparation

Preparing your Compression Horn Diaphragm

In order to fit your compression horn speakers into the pod, you need to remove the back plate. This keeps the mounting depth of the pod as shallow as possible. We designed the pods with a simple modification to the rear of the speaker.

We provide a protective plate because it is very important to the performance of your compression horns to cover the compression diaphragm element.

STEP 1

Working on a flat surface, turn your speaker face down

Close-up of gloved hands holding a black MB Quart speaker with screwdriver pins (no visible text or symbols on device)

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

STEP 2

Using a straight edge, gently peel up the back sticker

Person in gloves installing a black MB QIART speaker into a circular base (no text or symbols visible on the device itself)

STEP 3

Set the cool sticker aside so you can mount it on your machine later

STEP 4

With a #2 Phillips, hand operated screw driver, remove 4 screws from the back plate. Save these screws, they will be used to install the diaphragm cover plate.

Close-up of hands in black gloves installing a screwdriver on a black speaker base (no text or symbols visible)

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUARTI® MUSIC. DEFINED.

STEP 5

Set the back plate aside, it is un-needed

Close-up of hands in black gloves installing or repairing a mechanical component with visible wiring and components (no text or symbols)

DO NOT LEAVE IT EXPOSED

STEP 6

Use the supplied compression diaphragm cover to position over the aluminum dome.

Close-up of hands in black gloves installing or adjusting a mechanical component with a tool (no visible text or symbols)

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

STEP 7

Use the same screws you removed from the back plate to secure the compression dome diaphragm cover. Do not use a power drill. These screws should only be hand tight.

Repeat the process for the other compression horn speaker.

Close-up of hands in black gloves assembling a mechanical component with a yellow tool (no visible text or symbols)

SET THE SPEAKERS ASIDE TO PREPARE MOUNTING THE PODS TO RZR

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

MOUNTING THE PODS TO RZR

STEP 8 - TAPE IT OFF

Using colored painters tape, you need to mark the fender of the RZR where you will need to drill. To do this, hold an empty left or right pod in your hand. Hold the pod into place to approximate the position of the mounting holes on the internal fender.

Set the unit down and put colors tape onto the fender behind the pod until you can see the tape through the mounting holes when you hold the pod back into place.

Close-up of gloved hands installing or adjusting a mechanical component with a tool (no visible text or symbols)

Next, use your Sharpie to mark the mount holes on the painters tape. Repeat the mounting process for the other pod.

STEP 9 - DRILL

Drill (4) 5/16 inch holes into the fender where you marked the tape.

Close-up of a gloved hand using a power tool to adjust or install components on a mechanical component (no visible text or symbols)

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

STEP 10 - SECURE THE WIRES

Connect the wires from the amplifier or amplifier harness to the connectors on the back of the pods, left and right. Do not let it fall behind the pod as you are mounting.

STEP 11 - MOUNT THE PODS

Remove any tape from the fenders. With the included hardware mount the pod. The bolt and 1 washer mount through the fender, into the pod. This leaves only the head of the bolt visible behind the tire.

Close-up of a metallic industrial component with a circular opening and internal structure, no visible text or symbols.

Make certain you use a washer on the inside against the internal wall of the pod against the fender of the RZR. Use your 12 inch ratchet and wrench to secure the pod.

Close-up of a black industrial vehicle's side panel with visible springs and bolts (no text or symbols)

Mount the other RZR pod in the same manner.

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

STEP 12 - PREPARE THE WIRES

Secure the harness wires from inside each pod and connect the wires to the back of the compression horn speakers.

Close-up of gloved hands performing maintenance on a mechanical component with tools (no visible text or symbols)

Connect speaker wires

Close-up of a black plastic speaker head with exposed wiring and a small electronic component (no text or symbols visible)

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

MBQUART® MUSIC. DEFINED.

STEP 13 – MOUNTING THE SPEAKERS IN PODS

Working with each speaker as closely to the pod as possible, complete the wiring of the speaker to the pod and mount the speakers to the pod.

NOTE - If you would like to rotate the speaker left or right to change the angle of "level". Now is the time, use your 1/8 inch bit to do so now before final mounting of the speakers.

Using the included stainless steel screws mount the speakers to the pods. Use a hand screw driver to avoid damage to the pod.

Close-up of a person in gloves working on a mechanical component with a perforated circular component (no visible text or symbols)

Turn on your audio system. Check for the following, using the balance on the source unit to confirm Left is left and Right is right. Listen for a clear, crisp audio sound.

Congrats on a great install and an awesome audio upgrade. Get on the trails, show your friends and show us too. We're all over social, just like you. @MBQuart #MusicDefined #RZRLife

For additional technical information on this and all MB QUART products, go to the "SUPPORT" tab at MB QUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email. ©2018 Maxxsonics USA

NOTES PAGE

MOBILE POWERSPORTS MARINE MBI QUART AUDIO PRODUCTS

Exterior view of two black industrial fan units with speaker dividers and a MB-branded electronic device (no visible text or symbols)

MBQ-STG2-BT

STAGE 2, 400 WATT TWO SPEAKER RZR Tuned Audio Package

Installation Manual

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

INTRODUCTION

Thanks for choosing MB QUART. This RZR Tuned Audio System has been meticulously engineered to install into your vehicle. We have made the process so simple you will be in and out of the installation in couple hours.

This manual is laid out in CHAPTERS, for the STAGE 2 system; there are 14 CHAPTERS in total. Within each CHAPTER there may or may not be STEPS. Do them in the order presented to avoid mistakes and frustration.

UPGRADES

The up-arrow denotes an upgrade to your STAGE system is available. Different STAGE systems will be denoted within the CHAPTERS. You can always upgrade STAGE 2 with rear pods or a subwoofer creating a STAGE 3 or STAGE 5. Everything is defined in this manual and on the harness layout in CHAPTER 14.

Man standing beside a black and orange off-road vehicle with wheels, displayed in a video editing interface (no readable text or symbols on the vehicle itself)

INSTALL VIDEO

We strive to create a companion "how to" install video for most of our systems. The video will have additional details on making your installation a breeze.

If available, you can locate your specific video on the website. Just type in your model number in the search box and then look on the INSTALL & SUPPORT tab.

OVERVIEW SPECIFICATIONS SYSTEM INCLUDES INSTALL & SUPPOF Part #: MUG-5T05-1 | SKU: 806576229049 | Category: UTY & RZR Tuned Audio Description Polaris® RZR® Tuned Audio Package: FIVE SPEAKER 800 Watt STAGE 5 AUDIO SYSTEM with an AM/FM, Bluetooth Source Unit, Includes Front / Rear Compression horns with enclosures. 10 inch subwoofer with glove box enclosure and full harnessing YouTube

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

WARRANTY

Your audio system is covered by a 1 year warranty from the date of invoice. It is important that you keep your sales receipt. Furthermore, it is crucial that you record and store a record of the serial numbers for each of the components that are included in your system. In the rare instance that a warranty claim is needed both proof of purchase and serial numbers are required. Additional information is on the back page.

A) Sales Receipts show: the seller, date of purchase, model and price paid
B) Serial numbers for the components

INCLUDED

The STAGE 2 system ships in one box. Make sure to account for all components before attempting installation.

• Bluetooth Joystick controller
• Compact 2 channel amplifier
• Dual Amplifier Harness with mounting hardware
  • Dual Amplifier Mounting Plate (this system requires 1 amplifier only)
• Kick Panel Pods
• Two 8 inch compression horns (kick panel speakers)
• Two compression element diaphragm covers with instructional manual

If you feel something is missing, please contact Maxxsonics directly via email – [e-mail]

NOTE – Hardware for mounting components to enclosures and other items you will need are packed within the packaging for each piece. Do not dispose of any packaging until you have completely installed your system and certain you have accounted for every piece.

SAFETY

Prepare your machine to safely work on it and add accessories.

• Turn the ignition off and remove the key
• Remove the negative terminal of the battery (FIG S-1)
• Use a packing blanket other soft material to protect your machine
• Safety Glasses - always wear eye protection

Close-up of a car's battery undercarriage with tools and a red arrow pointing to the component (no visible text or symbols)

(FIG S - 1)

TIME & TOOLS

You will need about 3.0 HOURS to complete this installation depending on who is "helping."

The following are a list of tools you will need for any of the MB Quart UTV/RZR Tuned Audio packages. Depending on which system you are installing, you may or may not need all of them. You might also find you own more specialized tools to get the job done. Share the pics of your installation on our social channels to help others.

TOOLS YOU WILL NEED

• Wire Strippers and Crimpers
- 5/16" Drill Bit
- Drill
- Blue Painters Tape
- Marker
- 1/2'' Open Box Wrench
- 1/2'' Socket (preferably deep)
- 10mm Socket
- Ratchet
• T25 Torx Driver
- T40 Torx Driver
- Bojo Tools (Pry Tools)
- Flush cut wire cutters (Zip Ties snipping)
- 1 Friend

Besides the tools listed, you will also find it helpful to have some music ready for the TEST & TUNE step.

We recommend:

- Bluetooth Device like a phone with music or music app

CHAPTER 1 – PREPARATION FOR INSTALLATION

Before you start dismantling your machine, we suggest you prepare all your components, enclosures and harnesses.

These steps will follow the CHAPTERS of the Installation Videos when completed. Additionally, it will make life less stressful to have everything ready when you are ready to put each component into the machine.

STEP 1 - CONFIRMING POWER TO BUS BAR

The Polaris RZR and our Tuned Audio System requires a harness that connects the battery under the seat to the busbar harness that is located under the hood.

The harness is shown in FIG 1-1. Check that your machine has this harness installed. If not, you can purchase from your dealer or Polaris online. The part numbers are 2881551 or 2881646 depending on which machine you own.

Coiled black electrical fuse with red terminal connectors (no text or symbols visible)

(FIG 1-1)

PREPARATION

CHAPTER 2 – PREPARE YOUR KICK PANEL COMPRESSION HORNS

NOTE - Do not proceed with CHAPTER 3 until you have properly prepared the speakers with their compression diaphragm covers. Refer to the manual called MBQ-POD. You can also find this manual on-line by searching the model number.

Shown in FIG 2-1 is one picture from the MBQ-POD manual which will guide you step-by-step through preparing the kick panel compression horn speakers for installation into the kick panel enclosure and the RZR.

Close-up of hands in black gloves assembling a mechanical component with a yellow screwdriver (no visible text or symbols)

(FIG 2-1)

Removing the large back plate and installing the special compression horn diaphragm covers dramatically reduces the depth of the compression horns which ultimately allows our overall kick panel enclosure to be shallower than you would think. This assures maximum leg room for driver and passenger in the vehicle.

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

VEHICLE DISMANTLE

CHAPTER 3 - VEHICLE DISASSEMBLY

STEP 1 - REMOVE HOOD

Start with removing the hood. This is where you will access the bus bar (FIG 3-1). Confirm that your machine has the busbar installed by the dealer or by you. If your busbar harness has not been installed, see Chapter 1 of this manual for clarification

Person in gloves handling an orange and white patterned object with a star emblem (no visible text or symbols)

(FIG 3-1)

VEHICLE DISMANTLE

STEP 2 - REMOVE TOP OF DASH

Remove the top of the dash shown in FIG 3-2 by removing the screws.

Person in gloves installing or adjusting a black electronic device on a white platform (no visible text or symbols)

(FIG 3-2)

NOTE – Removing grab bar and seats allows easier access when installing rear pods and prepping for the subwoofer as part of a STAGE 5 system. You can run those wires for future access or leave them secured in the front of the vehicles.

CHAPTER 4 – PREPARE VEHICLE FOR AMPLIFIER MOUNTING PLATE

NOTE - Before installing the amplifier plate with the amplifier in position, you must prepare the mounting area in the vehicle.

The following instructions show the installation of both the full range and mono/subwoofer amplifiers. In this installation, you are using only the full range amplifier. You can upgrade to the subwoofer system which will include a mono amplifier specifically designed to run the subwoofer.

STEP 1 - Loosen the 16mm nuts that secure the steering column to the support frame shown in FIG 4.1. These nuts are very hard to loosen. Be careful.

Do not remove these steering column nuts, only loosen to create an 1/8 inch gap between the nut and the frame shown in FIG 4-2. You will not retighten these nuts until the Chapter 18 section of the installation manual.

LOOSEN DO NOT REMOVE

(FIG 4-1)

CREATE A GAP

(FIG 4-2)

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

CHAPTER 5 – BLUETOOTH CONTROLLER INSTALLATION

STEP 1 – Install the Bluetooth controller into a standard carling switch as shown in FIG 5-1. See the manual included with the unit for special mounting dimensions.

STANDARD SWITCH KNOCKOUT 3.5mm JACK ON BOTTOM (FIG 5-1)

NOTE - The 3.5mm input should be positioned on the bottom. This

CHAPTER 6 - INSTALL POWER HARNESS AT BUSBAR

Before we position the system harness and wire everything up we need to prepare the power portion of the harness.

NOTE – For any audio system and in fact electrical accessory for RZR you must have a busbar installed. The busbar brings power from the battery up to the back side of the dash. See Chapter 1 for busbar details.

STEP 1 - You will start at the bus bar. Lay the Power, Ground and Accessory portion of the harness in the vehicle and you begin to run each of the connectors to the appropriate component. The harness will run through the grommet shown in FIG 6-1.

GROMMET AGC GTD PBT

(FIG 6-1)

Slice the firewall grommet on the top side to the rubber as shown in FIG 6-2.

This will allow you to move the required harnesses from the Busbar to the dash and up to the amplifiers. You can use black electrical tape to seal the slice in the grommet now or during final inspection.

Close-up of hands installing or adjusting a car engine component with a blue tool (no visible text or symbols)

(FIG 6-2)

STEP 2 – Push the radio and amplifier connections through the grommet. Leave them accessible while you complete the connections at the busbar shown in FIG 9-2.

DO NOT USE PASSENGER SIDE GROMMET

(FIG 6-3)

NOTE – In some vehicles there is an unused grommet near the passenger foot well shown in FIG 6-3. DO NOT use this due to the placement of the subwoofer enclosure. Use the grommet picture that has a wire look present shown in FIG 6-2.

STEP 3 – Complete the connection at the busbar as shown in FIG 6-4. Mount the audio harness first, with the OEM RZR connections on top. This allows you to use the red boot on the powerline, keeping your install clean and looking factory installed.

SECURE THE RED BOOT ON THE POWER WIRE

(FIG 6-4)

Zip-tie this power portion of the harness into place. Assure that no added wiring is near any moving parts or components that generate large amounts of heat.

CHAPTER 7 – MOUNTING AMPLIFIERS & INSTALLATION

Mount your amplifier as pictures in FIG 7-1 on the dual amplifier plate.

NOTE - The following instructions show the installation of both the full range and mono/subwoofer amplifiers. In this installation, you are using only the full range amplifier.

When you upgrade and add the subwoofer system it will include a mono amplifier specifically designed to run the subwoofer.

When you upgrade to the rear pods, you will not need another amplifier, as this amplifier will run easily at 2 ohms, meaning all four speakers at the same time. That also doubles the effective power of the amplifier. More is better!

STEP 1 - With the amplifiers mounted to the plate, slide the Dual Amp Plate into position with the double groove portion of the bracket sliding between the steering column support shown in FIG 7-2 and the 16mm nuts and washers. Do not tighten down yet.

MOUNTING POINTS POWER & SPEAKER CONNECTIONS AUDIO CONNECTIONS AND ACCESS

(FIG 7-1)

NOTICE THE GAP

(FIG 7-2)

NOTE - The Dual Amplifier Harness is designed and laid out to perfectly connect power and speaker connections on the driver's side of the amplifiers while the RCA audio connections are on the passenger side of the RZR.

Make sure your amplifiers are mounted in the position shown in FIG 7-1. This configuration is critical to make sure you can access your fine tune adjustments for crossover and bass boost.

STEP 2 - On the front edge you will secure the plate with the 10mm bolt which secures the down strap that holds the back of the dash pocket shown in FIG 7-3.

DUAL AMP PLATE 10mm BOLT DOWN STRAP

(FIG 7-3)

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

NOTE – Once the amplifiers are connected, make the following adjustments to the setting. See CHAPTER 10 – TEST & TUNE for additional information on final system adjustments and best-settings.

TUNED PACKAGE	TWO CHANNEL AMPLIFIER	MONO AMPLIFIER
MBQ-STG-5-1	HP-OFF-LP/BPSwitch to HP - High Pass	Bass Boost to 0dB
MBQ-STG-3-1	HP-OFF-LP/BPSwitch to HP - High Pass	Bass Boost to 0dB
MBQ-STG-2-1	HP-OFF-LP/BPSwitch to – OFF	N/A
MBQ-SUBSYS-1	N/A	Bass Boost to 0dB

NA2-400.2 AMPLIFIER

X-OVER L HP OFF LP INPUT LEVEL HP LP R 9V 0.2V 15Hz 300Hz 50Hz 300Hz SEE CHART TO ADJUST

NA2-400.1 AMPLIFIER

BOOST L 0dB 12dB INPUT LEVEL LPF SUBSONIC 9V 0.2V 50Hz 150Hz 15Hz 50Hz SEE CHART TO ADJUST

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

CHAPTER 8 – DUAL AMPLIFIER & SPEAKER HARNESS CONNECTIONS

With your amplifier(s) mounted, we can now start laying in the speaker harness and plugging in all the connectors.

NOTE – While you are working on your system, we recommend covering the amplifiers to avoid scratching them or inadvertently hitting the crossovers with a wrench or screw driver.

STEP 1 – Plug in the power/ground connector of the two channel and the mono amplifier. At the same time, if you have illumination, connect the red/black. Additionally, you can connect the subwoofer and full range speaker connectors. See FIG 8-1.

NOTE – The following shows the Bluetooth controller in place, this is only reference for the amplifier connections that are mounted on the dual amplifier plate.

Review the full system wiring harness on Chapter 14.

graph TD
    A["Basebar"] --> B["R2F-8TOM Dual Amp Harness"]
    B --> C["Speaker Illumination Connection"]
    C --> D["Full Range Amplifier"]
    D --> E["Mono Amplifier"]
    E --> F["Subwoofer Enclosure"]
    D --> G["Rear RCA (R&L)"]
    D --> H["Front RCA (R&L)"]
    D --> I["Left Right"]
    E --> J["Left Right"]
    D --> K["Illumination +/- Right Speaker +/-"]
    E --> L["Illumination +/- Left Speaker +/-"]
    D --> M["All Speaker Connections Shown With Illumination"]
    M --> N["Kick Panel Enclosure"]

(FIG 8-1)

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

ILLUMINATION NOTE

For speakers that include illumination, there is a small red/black jumper wire and splitter that connects the rear speakers harness illumination wire to the left and right rear pod illumination.

You will make this connection in the same location as you are connecting the rear pods in the center console.

The connection location is the same for both the 2 and 4 seats RZR. Refer to the wiring diagram for proper placement. See wiring diagram in CHAPTER 14 for quick reference.

NOTE – Any excess wire that is gathered after the system is tested should be wire tied and secured under the seat. Do not allow any of the wire harness to touch heat generating or mechanical components of the machine.

CHAPTER 9 - MOUNTING THE KICK PANEL SPEAKERS

Through hundreds of installations, we have found it smartest to mount speakers and subwoofers in this order.

1) Driver kick panel
2) Subwoofer (If present at the time of installation)
3) Passenger side kick panel

STEP 1 - Using colored painters tape shown in FIG 9-1, you need to mark the fender of the RZR where you will need to drill. To do this, hold an empty left or right pod in your hand. Hold the pod into place to approximate the position of the mounting holes on the internal fender.

Close-up of a gloved hand cleaning a car engine component with a green adhesive clip (no visible text or symbols)

(FIG 9-1)

Set the unit down and put colors tape onto the fender behind the pod until you can see the tape through the mounting holes when you hold the pod back into place.

Next, use your Sharpie to mark the mount holes on the painters tape. Repeat the mounting process for the other pod Shown in FIG 9-2.

Close-up of gloved hands installing or adjusting a mechanical component with a white tool inside a black circular frame (no visible text or symbols)

(FIG 9-2)

STEP 2 - Drill (4) 5/16 inch holes into the fender where you marked the tape shown in FIG 9-3.

Close-up of a gloved hand using a power tool to clean or repair a green adhesive patch on a black vehicle (no text visible)

(FIG 9-3)

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

STEP 3 - Remove any tape from the fenders. With the included hardware, mount the pod. The bolt and 1 washer mount through the fender into the pod. This leaves only the head of the bolt visible behind the tire shown in FIG 9-4.

NOTE - Make sure that the wires behind the enclosure have remained accessible for connecting to the harness. Use some painters tape to keep them from getting blocked by the enclosure.

STEP 4 – Push the included bolt through a washer then through the fender

This will come through the fender and into the kick panel speaker enclosure.

BOLTS & WASHERS

(FIG 9-4)

STEP 5 - Using the 5/16 inch bolts, washers, and nuts, mount the enclosure shown in FIG 9-5.

NUTS & WASHERS

(FIG 9-5)

Make sure you use a washer on the inside of the enclosure against the internal wall of the pod which you sandwich against the fender of the RZR. Use your 12 inch ratchet and wrench to secure the pod.

Use a small racket and an open box wrench for convenience.

Wire the speaker and illumination if present and use the supplied screws to mount the speaker to the enclosure.

STEP 6 – Identify the harness wires from inside of each pod and connect the wires to the back of the compression horn speakers.

Close-up of gloved hands installing or adjusting a mechanical component with wires and tools (no visible text or symbols)

Connect speaker wires as shown in FIG 9-6.

Close-up of a black speaker wheel with exposed internal components and wiring, no text or symbols visible

(FIG 9-6)

For additional technical information, go to the "SUPPORT" tab at MBQUART.com

There you will find helpful, FAQ, TEQ Tips and you can contact Technical Support via email.

©2018 Maxxsonics USA

STEP 7 – With the speakers now properly wired, you can mount the speaker to the enclosure.

NOTE – The speakers shown being mounted here have already had their compression horn covers installed. This dramatically reduces the depth of the speaker ultimately allowing our kick panel enclosure to be shallower.

Refer to the compression horn diaphragm replacement manual included with the speakers called MBQ-POD.

Close-up of a gloved hand installing or adjusting a mechanical component with visible wiring and components inside a black circular housing (no text or symbols)

STEP 8 – With the compression horn wired properly you can position the speaker and mount with the included hardware. We suggest you mount with hand tools to avoid blowing out the screws. Final speaker position is shown in FIG 9-7.

Close-up of a gloved hand adjusting a circular mechanical component with perforated slots (no visible text or symbols)

(FIG 9-7)

Repeat the process from STEP 1 - 8 for the passenger side kick panel.

CHAPTER 10 - TEST & TUNE

Nearly done, but it is smart to confirm that everything is working before you put the machine back together. With the harness connected to the busbar, you can now reconnect the negative terminal of the battery.

RECONNECT BATTERY

Turn the ignition key to the ACC position and push the PWR button on your source unit.

NOTE – The following instructions are for confirming connectivity of the system you just installed. Refer to the Bluetooth controller manual for “pairing” instructions.

Here is a check list so you know you did not forget something.

With the power "ON" use the list here to check the system for all of the following. Make sure you are using the controls on the source unit to confirm Left is Left and Right is Right. There will be no change from Front to Rear as all speakers are on the same 2 channel amplifiers.

○ POWER ON
○ SPEAKERS - CONFIRM ALL YOUR SPEAKERS AND AMPLIFIERS ARE CONNECTED CORRECTLY

STEP 1 - FINE TUNING AMPLIFIER SETTINGS

Refer to CHAPTER 10 for baseline settings before proceeding with this section.

After you have confirmed and tested that all components are working you will tune the amplifiers. When setting up your amplifiers you will refer to the manual inside each amplifier. However, through hundreds of installations we have determined the following settings are ideal for the following STAGE Tuned Audio Packages.

Setup A Settings The illustrations below describe the various controls. Refer to the illustration that matches your amplifier. ① GAIN Adjustment The gain control purpose is to match the output of your source signal to the amplifier. Refer to the section B below for detained instructions. ② X-OVER Switch This switch will set the amplifier to have: a full frequency output or to filter out high or low frequencies. The NA1-400.2 offers either a bandpass or a high pass filter. ③ Frequencies Adjustment The Low Pass Filter will cut off the frequencies above the setting. The High Pass Filter will cut off the frequencies below the setting. ④ SUBSONIC Adjustment The Subsonic Filter will cut off the frequencies below the setting. If using with a subwoofer the settin should be kept between 15-25Hz. ⑤ BOOST Switch The Boost Switch will increase the signal 12dB at 4kHz. Be aware this setting can cover distribution if the gain is not set property.

B Level Setting This is a critical step to insure your amplifier is properly adjusted to match the signal output level of your source unit. GAIN MIN MAX THIS IS NOT A VOLUME CONTROL! 1. If possible, with the source unit off, confirm that the primary volume control is turned down (counter clockwise). 2. Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is turned down. Make sure the source unit controls; balance, fader, bassa and table are all set to center or '0' adjustment. Make sure that the green LED on the end of the amplifier is illuminated. 3. Play a clean musical selection of which you are very familiar. CD is preferred. Do not use radio signals for level setting. Hit play and start turning the volume of the source unit up. 4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until you hear speakers begin to slightly start producing distortion. 5. Increase the amplifier gain (clockwise) until distortion is heard, then back the level down (counter clockwise) until the distortion is eliminated. Small adjustments may need to be made to balance the levels of multiple amplifiers.

NOTE – Gain control, it is important to adjust each amplifier gain as described in the manual. Remember, these settings are NOT volume controls. Gain controls, properly adjusted help properly balance the system sound between lows, highs and minimize distortion that comes from the source unit.

UPGRADES – If you installed the STAGE 5, you are set. However, if you started with a STAGE 3 or STAGE 2, and are adding the subwoofer system or add rear pods, your amplifiers will need new settings.

Always check back to this guide to see if your amplifiers should be readjusted for the new components you have added.

Now, listen for a clear, crisp audio sound.

CHAPTER 11 - VEHICLE REASSEMBLY

Follow along the Dual Amplifier audio harness and zip tie the harness to the machine to assure it doesn't come loose during rides. Once your harness is secure, you can begin reassembling all the panels.

Here is a checklist so you do not forget anything – regardless of which system you installed:

○ WHEN REAR PODS ARE ADDED

• OIL COVER ON ENGINE COMPARTMENT BEHIND THE SEATS
  ○ CENTER CONSOLE
  ○ SEATS

• NUTS ON STEERING WHEEL COLUMN

• FRONT OF DASH - CHECK YOUR ALIGNMENT ON WHERE THE DASH MEETS TO THE SUBWOOFER
• TOP OF DASH
  ○ Hood

NOTE – It is critical to the safe operation of your vehicle that the nuts holding the steering column be retightened to 40 foot pounds of torque

CHAPTER 12 - FINAL INSPECTION

Here is a check list to make sure your vehicle is ready to hit the trails. You should Pull & Tighten everything so that you know your RZR and your audio equipment are secure.

• NUTS ON HARNESS AT THE BUS BAR
• ELECTRICAL TAPE ON THE SPLICE AT THE FIREWALL GROMMET
• LEFT KICK PANEL ENCLOSURE MOUNT AND WIRED
• RIGHT KICK PANEL ENCLOSURE MOUNT AND WIRED
  ○ AMPLIFIERS MOUNTED AND ALL 8 (4) NUTS ARE SECURED TO AMPLIFIER(S) ON THE PLATE
• NUTS ON STEERING WHEEL COLUMN
  ○ HARNESSES TO AMPLIFIERS
  ○ SPEAKER HARNESS AT AMPLIFIER
• FRONT AND REAR SPEAKER HARNESS AT AMPLIFIER
  ○ ACCOUNT FOR ALL YOUR TOOLS.

NOTE – It is critical to the safe operation of your vehicle that the nuts holding the steering column be retightened to 40 foot pounds of torque.

CHAPTER 13 - SHOW YOUR FRIENDS

Congrats on a great install and an awesome RZR audio upgrade. Get on the trails, show your friends and show us too. We're all over social media, just like you.

We use:

@MBQUART

MUSICDEFINED

RZRLIFE

RZR

CHAPTER 14 - LAYOUT HARNESS

In our design, you absolutely cannot make a mistake. Speaker connectors are color coded for front rear, left and right. If you accidentally make a mistake, it will not fit into the connector or bullet plug.

Refer to the harness layout shown on the next page to plug everything into the components.

graph TD
    A["Busbar"] --> B["RZR-BTDAH Dual Amp Harness"]
    B --> C["Source Unit"]
    C --> D["Rear RCA (R&L)"]
    C --> E["Front RCA (R&L)"]
    D --> F["Full Range Amplifier"]
    E --> F
    F --> G["Speaker Illumination Connection"]
    F --> H["Mono Amplifier"]
    H --> I["Subwoofer Enclosure"]
    F --> J["Illumination +/- Right Speaker +/-"]
    F --> K["Illumination +/- Left Speaker +/-"]
    J --> L["All Speaker Connections Shown With Illumination"]
    K --> M["All Speaker Connections Shown With Illumination"]
    L --> N["Kick Panel Enclosure"]
    M --> N
    N --> O["Speaker Harness"]
    O --> P["Illumination +/- Left Speaker +/-"]
    O --> Q["Illumination +/- Right Speaker +/-"]
    P --> R["Rear Pod Wiring Shown With Illumination"]
    Q --> S["Rear Pod Wiring Shown With Illumination"]
    T["Subwoofer Enclosure"] --> U["*4 Seat RZRs Use Provided Rear Speaker Wiring Extention*"]
    U --> V["Illumination Splitters"]
    V --> W["Illumination Splitters"]
    W --> X["Illumination Splitters"]
    X --> Y["Speaker Handless"]

RECORD RETAILER & PRODUCT INFORMATION HERE

Purchased From ____ ____

STORE NAME DATE OF PURCHASE

Bluetooth Controller ____ ____

MODEL NUMBER SERIAL NUMBER

Amplifier (2 channel) ____ ____

MODEL NUMBER SERIAL NUMBER

Front Speakers (Pr) ____ ____

MODEL NUMBER SERIAL NUMBER

NOTES PAGE

POWERSPORTS MOBILE MARINE QUART AUDIO PRODUCTS