Valera 9723ES - TV Stand BDI - Free user manual and instructions

USER MANUAL Valera 9723ES BDI

A - Phillips Screwdriver [Not Provided]

B - 4mm Hex L-Wrench

C - Cam Fastener x 4

D - Dowel Pin x 8

E - Cam Bolt x 4

F - 1/4-20 x 38mm

Machine Screw x 6

G - M6 x 16mm Machine Screw 9721, 9723 x 6 9724 x 8

H - M6 x 6mm Machine Screw 9721, 9723 x 6 9724 x 8

Isometric line drawing of a rectangular mechanical part with a circular recess and mounting holes (no text or symbols)

I - Upper Bracket 9721, 9723 x 3 9724 x 4

Technical line drawing of a mechanical bracket component (no text or symbols)

J - Lower Bracket 9721, 9723 x 3 9724 x 4

K - Shelf Clip 9721 x 8 9723, 9724 x 4

L - #6 x 1/2" Wood Screw 9721 x 8 9723, 9724 x 4

M - Rubber Stem Bumper x 6

N - Top Panel x 1

0 - Side Panels x 2

P - Base Assembly x 1

Q - Back Panel x 1

R - Glass Shelves 9721 x 3 9723, 9724 x 2

Valera is engineered for easy assembly. Carefully follow this procedure to prevent any damage.

Placement and Maintenance

Valera is designed for indoor use on level floors. Clean glass with glass cleaner, and wood veneer with a moist cloth.

Line drawing of a multi-tiered refrigerator cabinet (no text or labels)

9721

Line drawing of a closed refrigerator with two shelves and a top casing (no text or symbols)

9723

Line drawing of a multi-tiered rectangular appliance with two recessed compartments and mounting holes (no text or symbols)

9724

Step 1

Unpack and Identify

Unpack and identify the components at left. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at [e-mail]. For all other concerns, please contact your BDI Retailer.

N O Q O R P

Step 2
Install Hardware onto Top Panel

p 2 all Hardware onto Top Panel Top Panel (N) on its Top on a carpeted surface, with holes facing up. all Dowel Pins (D) and Cam Bolts (E) into Top Panel (N) using Phillips ewdriver (A). all Upper Brackets (I) onto Top Panel (N) with Machine Screws (G) ing 4mm Hex L-Wrench (B), do not fully tighten for ease of Back Panel installation.

Step 3
Install Hardware into Side Panels

Install Cam Fasteners (C) into Side Panels (O) as shown, align arrow on Cam Fastener (C) to point up.

Cam Fastener (C)
Arrow to point up to start

Two isometric diagrams of rectangular panels labeled O and C, with no text or symbols present.

Step 4
Install Hardware into Bottom Panel
Install Lower Bracket (J) into Base Assembly (P) with Machine Screws (G) and tighten using 4mm Hex L-Wrench (B).
Do not fully tighten Brackets for ease of Back Panel (Q) installation.

P B G J

Step 5

Step 5 Attach Side Panels to Top Panel attach Side Panels (O) to Top Panel (N) by lowering Side panels (O) onto Dowel Pins (D) and Cam Bolts (E). Make tain shelf pin holes face inward. lighten Cam Fasteners (C) with 4mm Hex L-Wrench (B).

Step 6

Attach Base Assembly
Insert Dowel Pins (D) into Side Panels (O).
Attach Base Assembly (P) to Side Panels (O) using Dowel Pins (D) to align components. Make certain Upper
Brackets (I) and Lower Brackets (J) are on same side. Tighten Machine Screws (F) with 4mm Hex L-Wrench (B). After Base Assembly (P) is attached turn Unit over.
CAUTION: Do not turn unit over on Brackets.

Recommended
2-person Step for easy installation

P B F D D D O N F F F O

Step 7

Install Back Panel

Install Back Panel (Q) onto Upper Brackets (I) and Lower Brackets (J) with Machine Screws (H) using 4mm Hex L-Wrench (B).

Fasten the Machine Screws (H) in the middle of the Back Panel (Q) and then fasten the outside Machine Screws (H).

After Back Panel (Q) is installed, then tighten Upper Brackets (I) and Lower Brackets (J).

H B H H H Fasten the screws in the middle of the panel and then fasten the outside screws.

Step 8
Set Swivel Position

Valera 9721, 9723 and 9724 feature a swiveling base. Note that Swivel-Lock Pins are factory-installed at Position 1 enabling the stand to swivel 15-degrees to left and 15-degrees to right.

To lock the stand in a fixed position, use Hex Driver (B) to remove both Swivel-Lock Pins from Position 1 (factory position) and re-install them at Position 2.

To unlock the swivel for 360 degree rotation, remove Swivel-Lock Pins.

Swivel-Lock Pins

Position 2 Position 1 Fixed Swivel

Step 9
Install Glass Shelves

Note: Glass Shelves (R) are identical.

Install Rubber Stem Bumpers (M) into Base Assembly (P).

Install Lower Glass Shelf (R) onto Base Assembly (P). Slowly slide Glass Shelf (R) into place under Lower Brackets (J).

Install Shelf Clips (K) into Side Panels (O) at desired height and tighten with Phillips Screwdriver (A). Make certain set screw on Shelf Clips (K) faces down. Install Middle Glass Shelf (R) into Shelf Clips (K) and tighten set screws on Shelf Clips (K) with Phillips Screwdriver (A).

Shelf Clip (K)
Set screw faces down.

Recommended 2-person Step for easy installation

Glass Shelf (R) + Brackets (J). ASSEMBLY INSTRUCTION

Carefully slide Glass Shelf (R) under Lower Brackets (J).