USR4500-RMK - Modem USRobotics - Free user manual and instructions

Product Type	Rack Mount Kit (RMK)
Brand	USRobotics
Model	USR4500-RMK
Rack Space	1U
Compatible Devices	USRobotics 5" x 5" TAP devices
TAP Device Capacity	Three
Dimensions (H x W x D)	1.725" x 19.000" x 6.250" (44 mm x 483 mm x 159 mm)
Chassis Weight	3 lb (1.36 kg)
Shipping Weight	6 lb (2.72 kg)
Package Contents	RMK chassis, 10 cable tie downs, information card
Installation	Rack mount; TAP devices can be inserted before or after mounting chassis
Knockout Removal	Push, pry, and wiggle until metal tabs fail
TAP Device Installation	Insert into knockout, slide align tab into align slot, tighten thumb screw
Power Cable Management	Use cable tie downs through 3/16" holes; allow 10" slack; cinch firmly
Redundant Power	Second power adapter recommended on different circuit for uninterrupted monitoring
Warranty	USRobotics Limited Warranty; see www.usr.com/support/4500
Technical Support	www.usr.com/support
Application	Neat, orderly, professional installation with monitoring/analysis access

Frequently Asked Questions - USR4500-RMK USRobotics

What is the USRobotics USR4500-RMK?

The USR4500-RMK is a rack mount kit designed to hold up to three USRobotics 5" x 5" TAP devices in a standard 19-inch rack, occupying 1U of space.

How many TAP devices can the USR4500-RMK accommodate?

It can accommodate three USRobotics 5" x 5" TAP devices.

What are the dimensions of the USR4500-RMK?

The dimensions are 1.725" x 19.000" x 6.250" (44 mm x 483 mm x 159 mm).

What is the weight of the USR4500-RMK chassis?

The chassis weight is 3 lb (1.36 kg), and shipping weight is 6 lb (2.72 kg).

How do I install a TAP device in the USR4500-RMK?

First, remove a knockout by pushing, prying, and wiggling until the metal tabs fail. Then insert the TAP device, slide the align tab into the align slot, and tighten the thumb screw.

Can I install TAP devices before mounting the RMK chassis in the rack?

Yes, you may choose to insert TAP device(s) before or after RMK chassis installation.

How should I manage power cables for the TAP devices?

Use the provided cable tie downs through the 3/16" holes behind each TAP opening. Allow approximately ten inches of slack clearance, then cinch firmly without deforming the cable sheath.

What is the warranty for the USR4500-RMK?

It is covered by the USRobotics Limited Warranty. For details, visit www.usr.com/support/4500.

Where can I get technical support for the USR4500-RMK?

Technical support information is available at the USRobotics corporate website: www.usr.com/support.

What is the purpose of the USR4500-RMK?

It provides a high quality, space-saving rack mount solution for a neat, orderly, and professional installation of multiple USRobotics TAP devices, particularly where access for monitoring and analysis is important.

USER MANUAL USR4500-RMK USRobotics

Rack Mount Kit Installation Guide

Black metal rack-mounted device labeled 'USR4500-RMK 3-Unit Tap Rack Mount' (no other text or symbols visible)

Package Contents:

• USR4500-RMK 3-Unit Tap Rack Mount
- Package of 10 cable tie downs
• Information card

Introduction — The RMK (Rack Mount Kit) is a high quality, space saving rack mount chassis used with multiple USRobotics 5" x 5" TAP devices for a neat, orderly and professional installation. Typically, the RMK chassis is installed where access with monitoring and analysis capabilities are important.

USR4500 RMK (3 Tap Unit) Specifications:

• Occupies 1U of rackspace
• 5" x 5" TAP Device Capacity: Three
• Dimensions H x W x D: 1.725" x 19.000" x 6.250; 44 mm x 483 mm x 159 mm
• Weight: Chassis - 3 pounds; 1.36 kg: Shipping - 6 pounds; 2.72 kg

RMK Installation — You may choose to insert TAP device(s) before or after RMK chassis installation.

- Select a location and align the RMK chassis holes with the corresponding rackspace holes. WARNING: Installing on a universal flange middle hole will result in the RMK chassis invading an adjoining standard 1U rackspace.

- Insert and tighten screws until the RMK chassis is secure in the rack.

USRobotics®

Installing a small form TAP device:

• Remove knockout by gently pushing, prying and wiggling it until metal tabs fail, then dispose of it.
• Insert the TAP device into the knockout opening and slide the align tab on the rackmount into the align slot of the TAP.
• Tighten the thumb screw until the TAP device is secure in the RMK chassis.

Power Cable Management:

For models with redundant power available, it is strongly recommended that the second power adapter be used to assure uninterrupted monitoring. To eliminate power as a single point of failure connect the second power adapter to a different external power source circuit. To minimize power connector stress caused by suspending the cable and power adapter, it is highly recommended that strain loops be required for the

power cable in this critical area.

- Allow approximately ten inches of slack clearance between the power connectors and the power cable tie down. This will allow sufficient clearance to plug in the power connectors. Thread a cable tie down through the two 3/16" holes located directly behind the TAP device opening. Place the power cables in the cable tie down and cinch firmly but not so tight as to deform the cable sheath.

- Trim the excess cable tie to minimize space and provide a clean cabling installation. Cable management considerations should deliver quality in installation consistent with industry standards to improve the level of cabling regulation compliance.

Warranty and Support Information:

This product is subject to the U.S. Robotics Corporation Limited Warranty. To view a copy of the Limited Warranty, please see: www.usr.com/support/4500

For information on how to contact USRobotics Technical Support, please see the USRobotics corporate web site at: www.usr.com/support