ZH6020X - Kitchen hood ZANUSSI - Free user manual and instructions
Find the device manual for free ZH6020X ZANUSSI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Kitchen Hood |
| Brand | Zanussi |
| Model | ZH6020X |
| Width | 60 cm |
| Depth | 50 cm |
| Height | 15 cm (without chimney) |
| Weight | 12 kg |
| Power Supply | 220-240 V ~ 50 Hz |
| Motor Power | 120 W |
| Max Extraction Rate | 600 m³/h |
| Number of Speeds | 3 |
| Noise Level (max speed) | 68 dB |
| Lighting | 2 x 40 W halogen |
| Control Type | Push buttons |
| Grease Filter | Aluminum, washable |
| Charcoal Filter | Optional (for recirculation) |
| Installation Type | Wall-mounted |
| Ducting | 150 mm diameter |
| Energy Efficiency Class | A |
| Annual Energy Consumption | 55 kWh |
Frequently Asked Questions - ZH6020X ZANUSSI
How to install the Zanussi ZH6020X kitchen hood?
Installation should be done by a qualified person. Ensure the hood is mounted at least 65 cm above the hob. Use the provided template to mark drill holes, then secure the chimney and connect the ducting (if in extraction mode) or insert the charcoal filter (if recirculation mode). Finally, connect to mains power.
How to clean the grease filter?
Remove the grease filter regularly (every 2-3 months). Wash it by hand with warm water and mild detergent, or in the dishwasher at low temperature. Let it dry completely before reinstalling.
How to replace the charcoal filter?
Charcoal filters cannot be washed and must be replaced every 4-6 months, or more often with heavy use. Remove the grease filter first, then slide out the old charcoal filter and insert a new one. Ensure it locks into place.
Why is my Zanussi hood not extracting effectively?
Check if the grease filter is clogged and clean it. If using recirculation mode, replace the charcoal filter. Also ensure the ducting is not blocked or kinked. Check that the hood is recirculating properly if no duct is connected.
How to change the halogen bulbs in the hood?
Disconnect the hood from power. Remove the bulb cover by gently prying it open. Replace the halogen bulb (40W, G4 base) with a new one, taking care not to touch the glass with bare fingers. Reattach the cover.
What are the dimensions for ducting connection?
The ducting connection is 150 mm diameter. Use smooth-walled ducting for best performance. If reducing to 120 mm, note that efficiency may decrease.
Can I operate the hood in recirculation mode?
Yes, you can use the hood in recirculation mode by installing optional charcoal filters. The air will be filtered and returned to the kitchen. Ensure the outlet is not obstructed.
How to reset the filter saturation indicator?
After cleaning or replacing filters, press and hold the 'Speed 1' button for about 3 seconds until the indicator light turns off. This resets the timer.
What is the noise level of this hood?
The noise level varies by speed: approximately 55 dB on low speed, 62 dB on medium, and 68 dB on high speed. These values are measured at a distance of 1 meter.
Why is the hood not turning on?
Check if the mains power is connected and the circuit breaker is on. Ensure the hood is properly wired. If the problem persists, contact a qualified technician.
User questions about ZH6020X ZANUSSI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Kitchen hood in PDF format for free! Find your manual ZH6020X - ZANUSSI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ZH6020X by ZANUSSI.
