IM4249 ULTRAGLISS - Iron MOULINEX - Free user manual and instructions

Product Type	Steam Iron
Brand	Moulinex
Model	IM4249 ULTRAGLISS
Power Supply	220-240 V ~ 50/60 Hz
Water Tank Capacity	Approximately 300 ml (fill to MAX mark)
Soleplate Material	Ultragliss (non-stick coated)
Steam Output	Continuous steam, adjustable with steam control
Steam Boost	Yes, Boost button for extra steam
Spray Function	Yes, dampens laundry
Vertical Steaming	Yes (depending on model)
Anti-Calc System	Removable anti-calc valve
Self-Clean Function	Yes, monthly recommended
Easycord System	Yes, cord guide with button
Thermostat Control	Adjustable, with indicator light
Automatic Shut-Off	Not specified (must not be left unattended)
Cord Length	Approximately 2 m (estimate)
Weight	Approximately 1.2 kg (estimate)
Dimensions (L x W x H)	Approximately 30 x 12 x 15 cm (estimate)
Maintenance	Clean anti-calc valve monthly, self-clean monthly, clean soleplate with soft cloth
Safety	Do not immerse in water, unplug before filling, use on stable surface
Repairability	Approved Service Centre for repairs

Frequently Asked Questions - IM4249 ULTRAGLISS MOULINEX

What type of water should I use in the Moulinex IM4249 ULTRAGLISS iron?

Use untreated tap water. If water is very hard, mix 50% tap water with 50% demineralised water. Never use pure demineralised water, water from tumble dryers, scented water, softened water, or other types listed in the manual.

How do I fill the water tank?

Unplug the iron, set steam control to 0, open the reservoir hatch, fill to MAX mark, then close the hatch. Do not exceed MAX.

Why is water dripping from the soleplate?

The temperature may be too low for steam. Set thermostat to steam range (•• to MAX) and wait for light to go out. Also avoid using Boost too frequently.

How do I clean the anti-calc valve?

Unplug iron and empty tank. Press self-clean button to remove valve. Soak in white vinegar or lemon juice for 4 hours, rinse, and replace.

How to perform the self-clean operation?

Unplug iron, set steam to 0, fill tank to MAX. Set thermostat to MAX, plug in and wait for light to go out. Unplug, place iron horizontally over sink, remove anti-calc valve, gently shake until water runs out. Replace valve, plug in for 2 minutes on heel to dry.

Can I use the iron vertically?

Yes, for hanging garments. Set thermostat to MAX, hold iron a few cm from fabric, press Boost button repeatedly moving top to bottom. Do not direct steam at people or animals.

How do I store the iron?

Set steam to 0, unplug, empty tank, let cool. Use Easycord system to wind cord. Store on its heel.

What should I do if brown streaks appear on laundry?

Do not use chemical descaling agents. Check water type (see manual). Perform self-clean and clean soleplate with damp sponge. Ensure laundry is rinsed properly.

Why is there little or no steam?

Check water tank is filled. Clean anti-calc valve if dirty. Perform self-clean to remove scale. If iron was used dry for too long, self-clean may help.

How do I use the Easycord system?

Press the button on the base to deploy the cord guide. This prevents the cord from trailing across laundry. To store, slot into notch and press to retract.

USER MANUAL IM4249 ULTRAGLISS MOULINEX

Exterior view of a steam iron with model number Moulinex (no text or symbols on body)

Diagram showing a car tire being lifted by a lift into a trash bin (no text or symbols present)

Diagram of a mechanical device with a belt and lever, shown in circular motion (no text or symbols)

Illustration of a steam iron being placed on its side, showing the blade and handle (no text or symbols)

Diagram of a device inside a container with directional arrows indicating motion (no text or symbols)

Illustration of a bowl with a star-shaped object inside, enclosed in a circular frame (no text or symbols)

Close-up of a car seatbelt mechanism with a black arrow indicating force or pressure (no text or symbols present)

Close-up of a car interior showing a hand pressing down on the steering wheel (no text or symbols visible)

Illustration of a hand washing an iron inside a circle, with arrows indicating direction (no text or symbols)

Illustration of a hand using a syringe to interact with a mechanical component (no text or symbols visible)

Mechanical assembly diagram showing a hand operating a lever mechanism (no text or symbols visible)

Illustration of a steam iron inside a circular frame, labeled 'fig.13' (no text or symbols on the diagram itself)

Description

1. Spray
2. Reservoir refilling hatch
3. Steam control
4. Anti-calc valve
5. Self-Clean button
6. Spray button
7. Boost button

(depending on model)

1. Easycord system (cord guide)
2. Electric power cord
3. Easycord system extension button
4. Thermostat indicator light
5. Thermostat button
6. Temperature setting indicator
7. Reservoir max indicator
8. Soleplate

For your safety

• This appliance complies with the technical rules and standards for safety currently in force (Electromagnetic Compatibility, Low Voltage, Environnement).
• This appliance is not designed to be used by children or other persons unassisted or unattended if their physical, sensory or mental capacities prevent them from using the appliance in complete safety. Children should be supervised to ensure that they do not play with the appliance.
• Caution, before plugging in your iron, check that your mains voltage corresponds to the voltagee indicated on the information panel on the iron. Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee.
• This iron must always be plugged into an earthed socket. If using a mains extension lead, ensure that it is correctly rated. If you use an extension lead, check that it is adapted to the power indicated on the information panel on the iron.
• If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger.
• The appliance should not be used if it has fallen, if it has obvious damage, if it leaks or has functional anomalies. Never dismantle your appliance: have it inspected by an Approved Service Centre, so as to avoid any danger.
• Never immerse your iron in water!
• Do not unplug your appliance by pulling on the cord. Always unplug your appliance: before filling or rinsing the reservoir, before cleaning it, after each use.
• Never leave the appliance unsupervised when it is connected to a power source; if it has not cooled down for approximately 1 hour.
• Your appliance gives off steam, which may cause burns, especially when you are ironing on a corner of your ironing board. Never direct the steam towards people or animals.
• Your iron should be used and placed on a stable surface. When you put your iron onto its iron rest, make sure that the surface on which you put it is stable.
• This product has been designed solely for domestic use. Any inappropriate use or use contrary to the instructions releases the brand from all responsibility and renders the guarantee invalid.

Before first use

• Before using your iron with the steam function for the first time, we recommend that you operate it in a horizontal position for a few moments, away from your linen, i.e. press the Boost button ⚙ a few times (depending on model).
• During the first few uses, a harmless odour and smoke may be given off. This has no effect on the use of the iron and will disappear quickly.

Please read these instructions carefully and keep them for future reference.

Remove and throw away the plastic part that protects the cord (A). Remove any labels from the soleplate before heating up the iron (depending on model).

GB

What water to use?

If you have very hard water, mix tap water with commercially available demineralised water in the following ratio:

- 50% tap water, - 50% demineralised water.

• Your appliance has been designed to function with untreated tap water. However, Self-cleaning of the appliance should be carried out once a month.
• Never use any of the types of water below that contain organic waste or mineral elements and may cause spitting, brown staining or premature ageing of your appliance: commercially available pure demineralised water, water from tumble dryers, scented water, softened water, water from refrigerators, water from batteries, water from air conditioners, distilled water, rain water, boiled or filtered water, bottled water, etc.
• The integrated anticalc system (depending on model) gives better quality ironing: a constant flow of steam throughout the ironing session and lasting performance of your appliance.

Preparation

Filling the water tank

• Unplug your iron before filling it and set the steam control to .0. (fig.1).
• Open the reservoir refilling hatch (fig.2), place the iron flat and fill it (fig.3).
• Close the reservoir refilling hatch.

Fill the tank up to the "MAX"

Deploy the Easycord system

Always use the Easycord system for enhanced comfort of use.

• Your iron is equipped with the Easycord system to prevent the cord trailing across the laundry and creasing it during ironing.
• Press the button located on the base (fig.4) and the Easycord system is automatically deployed. You can now plug in your appliance and begin ironing.

Use

Adjust the temperature and the steam

• Adjust the thermostat button (fig.5), consulting the table below.
• The thermostat light comes on (fig.6). It will go out when the soleplate is hot enough.

It is normal for the indicator light to switch on and off during ironing

- Set the steam control (fig.7) to the desired position, consulting the table below.

FABRIC	POSITION OF THERMOSTAT CURSOR	STEAM SETTING POSITION
LINEN	MAX	.3.
COTTON		.2.
WOOL		.1.
SILK
SYNTHETIC (Polyester, Acetal, Acrylic, Nylon)		.0.

= STEAM ZONE

- Your iron heats up quickly: so begin by ironing fabrics that are ironed at low temperatures first, then go on to those requiring a higher temperature.

In order to avoid water dripping from the iron onto the linen:

- turn off the steam when ironing silk or synthetic fabrics.

- set it at the minimum position for weol. If you turn down the thermostat, wait until the thermostat light comes back on before beginning to iron again. When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate fibre. For delicate fabrics we recommend testing the fabric first on an inconspicious place eg (inside the hem).

If you want to dry iron, set the Steam control to *.0.*

Obtain more steam (depending on model)

Wait a few seconds between each shot before pressing the button again.

- Press the Boost button now and again to remove stubborn creases (fig.8).

Spray Function

- Whether steam or dry ironing, you are able to use the Spray button (fig.9) to dampen laundry to remove stubborn creases.

Vertical steam ironing (depending on model)

Every fifth time you press the button, return the iron to the horizontal position. The steam is very hot, so you should always do this with the garment on a hanger – never while someone is wearing it.

Ideal for removing creases in suits, jackets, skirts, curtains, etc.:

• Hang the garment on a hanger and hold the fabric slightly taut with one hand.
• Set the thermostat control to MAX (fig.5).
• Press the Boost 🤗 button repeatedly (fig.8) moving the iron from top to bottom (fig.10).
• Hold the iron a few centimetres from the fabric to avoid burning delicate fabrics.

Store your iron

• Set the steam control to and unplug the iron.
• Wait until the soleplate cools down and empty the reservoir. A little water may remain in the reservoir.
• To wind the cord around the heel of the iron, slot the Easycord system into the notch (fig.11). Take the end of the Easycord system and press to make the flexible part go back into the base (fig.12). Wind the cord.
  • Store the cold iron on its heel (fig.13).

Maintenance and cleaning

Cleaning the anti-calc valve (once a month)

• Unplug your iron and empty the water tank.
• Press the self-clean ejection button (fig.14a) and remove the anti-calc cartridge (fig.14b).
• Soak the valve in a cup of white spirit vinegar or plain lemon juice for 4 hours.
• Rinse the valve under running water and Replace the anti-calc valve.

Unplug your iron and let it cool down before cleaning it.

The iron will not function without the anti-calc valve. Never touch the end of the valve I

— Carry out the self-cleaning operation (once a month)

To slow down scaling and prolong the useful life of your iron, carry out the self-cleaning operation once a month.

• Unplug your iron, set the steam control to and fill the water reservoir to MAX.
• Place your iron on its heel, set the thermostat button to MAX, plug in your iron and wait for the indicator light to go out.
• Unplug the iron and place it horizontally over a sink.
• Press the self-clean ejection button (fig.14a) and remove the anticalc cartridge (fig.14b).
• Gently shake the iron over the sink until some of the water (along with impurities) runs out through the soleplate.
• At the end of the operation, put the anticalc cartridge back in place and then plug in your iron for 2 minutes on its heel to dry the soleplate.

Cleaning the soleplate

- Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth.

Never use abrasive or aggressive products.

If there is a problem

PROBLEM POSSIBLE CAUSE SOLUTION
Water drips from the holes in the soleplate.	The chosen temperature is too low and does not allow for the formation of steam.	Position the thermostat in the steam range (from •• to MAX).
	You are using steam while the iron is not hot enough.	Wait until the thermostat light goes out.
	You are using the Boost button too often.	Wait a few seconds between each use of the button.
	There is too much steam.	Reduce the steam.
	You have stored the iron horizontally, without emptying it and without setting it to • . 0 . •	See the section "Storing your iron".
Brown streaks come through the holes in the soleplate and stain the linen.	You are using chemical descaling agents.	Do not add any descaling agents to the water in the water tank.
	You are not using the right type of water.	Perform a self-cleaning operation and consult the chapter "What water should I use?".
	Fabric fibres have accumulated in the holes of the soleplate and are burning.	Perform the self-cleaning operation and clean the soleplate with a damp sponge. Vacuum the holes of the soleplate from time to time.
	Your linen has not been rinsed sufficiently or you have ironed a new garment before washing it.	Make sure that your laundry is rinsed sufficiently so as to remove any deposits of soap or chemical products on new clothes.
The soleplate is dirty or brown and can stain the linen.	Your are ironing with an inappropriate program (temperature too high).	Clean the soleplate as indicated above. Select the appropriate program.
	You are using starch.	Clean the soleplate as indicated above. Always spray starch onto the reverse side of the fabric to be ironed.
There is little or no steam.	The water tank is empty.	Fill it.
	The anti-calc valve is dirty.	Clean the anti-calc valve.
	Your iron has a build-up of scale.	Clean the anti-calc valve and carry out a self-clean.
	Your iron has been used dry for too long.	Carry out a self-clean.
The soleplate is scratched or damaged.	You have placed your iron flat on a metallic rest-plate or ironed over a zip.	Always set your iron on its heel.
Steam or water come from the iron as you finish filling the tank.	The steam control is not set to the • . 0 . • position.	Check that the steam control is set to the • . 0 . • position.
	The water tank is overfilled.	Never exceed the Max level.
The spray does not spray.	The water tank is not filled enough.	Fill up th water tank.

If you have any problem or queries, please contact our Customer Relations team first for expert help and advice.

Descripción