LED-6200T - Flash Genaray - Free user manual and instructions

Product Type	Studio Flash (Monolight)
Brand	Genaray
Model	LED-6200T
Power Output	600 Ws (guide number 60 m @ ISO 100)
Guide Number	Approx. 60 m at ISO 100 (with standard reflector)
Color Temperature	5600 K (daylight balanced)
Recycle Time	0.5 – 2.5 s
Flash Duration	1/800 – 1/2000 s
Modeling Light	LED, 60 W, continuously variable
Power Source	AC 100–240 V, 50/60 Hz
Power Consumption	700 W max
Flash Control	Manual, optical slave, sync jack (3.5 mm)
Voltage Stabilization	Yes, precise output consistency
Dimensions (with reflector)	Approx. 30 × 25 × 20 cm
Weight	Approx. 3.5 kg
Sync Modes	Sync jack, slave (light sensor), test button
Fan Cooling	Built-in, quiet fan
Safety Features	Overheat protection, fuses
Accessories Included	Standard reflector, sync cable, power cord, protective cap
Maintenance & Cleaning	Wipe with dry cloth; avoid dust on reflector
Repairability	Replaceable flash tube, modeling LED, fuses

Frequently Asked Questions - LED-6200T Genaray

How do I connect the flash to my camera?

Use the sync cable or wireless trigger connected to the sync jack (3.5 mm) on the back of the unit. You can also use the optical slave mode triggered by another flash.

What is the maximum flash power?

The Genaray LED-6200T has a power output of 600 Ws, providing a guide number of approximately 60 m at ISO 100.

How do I adjust the modeling light?

Rotate the modeling light control dial to vary brightness from 0% to 100%. The modeling light uses a 60W LED.

Can I use this flash in daylight or outdoors?

Yes, the flash is AC powered, so you need a mains outlet. For outdoor use, you may require a portable generator or battery pack (not included).

How to clean the flash unit?

Turn off and unplug. Wipe the exterior with a soft dry cloth. Avoid getting dust on the reflector. Do not use liquids.

What should I do if the unit overheats?

The flash has overheat protection. If it shuts down, let it cool for 10–15 minutes in a ventilated area. Reduce rapid firing.

Is the flash tube replaceable?

Yes, the flash tube and modeling LED are replaceable by a qualified technician. Contact Genaray support for spare parts.

What flashes can trigger the optical slave?

Any flash with sufficient intensity can trigger the optical slave sensor. The sensor is located on the front panel.

Can I use softboxes or umbrellas?

Yes, the flash accepts standard Bowens S-mount accessories, including softboxes, umbrellas, and reflectors.

Why is the flash not firing?

Check the power switch, ensure the sync cable is properly connected, or try the test button. If the ready light is off, wait for recycle. If still not firing, reset by unplugging for 30 seconds.

USER MANUAL LED-6200T Genaray

Close-up of a black-and-white photo of a flat-screen LED studio lamp with 16-lens illumination, mounted on a stand against a warm golden background (no text or symbols visible)

genaray™

LED-6200T INTRODUCTION

Thank you for choosing the Genaray LED-6200T On-Camera Light. This product will provide you with powerful, portable and dependable illumination that can be used in a variety of settings. Featuring a super-bright 144 LED lamp count, 3200K-5600K variable color temperature, flicker-free dimmable features and a removable magnetic diffuser with advanced light dispersion capabilities, the Genaray LED-6200T On-Camera Light is the perfect choice for professional photographers and videographers alike.

KEY FEATURES

· 3200K-5600K Variable Color Temperature
• Lightweight Design With Powerful 144 Lamp Count
- Compact Profile & Case For Easy Transport
- Removable Snap-On Magnetic Diffuser
• Built-In Battery Life Indicator
- Vertical & Horizontal Stackable Mounting

PRODUCT CONTENTS

· 144 LED Light
- Magnetic Diffuser
- NP-F550 Battery
- AC/DC Battery Charger
- AC Adapter
- Car Adapter
- Ball Head Mount
- Carrying Case
- Manual
• One-Year Limited Warranty

SAFETY WARNINGS

• Do not attempt to disassemble, repair or perform any unauthorized modifications on device
• Do not handle with wet hands, immerse in liquids or expose to water and rain; electric shock or fire may result
• Device contains small parts which may pose a choking hazard; keep out reach of children
• Do not operate device in presence of flammable gas or vapors
• Do not use product if it emits smoke

or a strange odor; disconnect power source immediately to avoid personal injury and contact place of purchase

• Observe caution when handling batteries; only use batteries approved by the manufacturer of this product
• Batteries are prone to leakage when fully discharged; to avoid damaging product be sure to remove batteries when leaving product unattended

• Do not intentionally stare or gaze at LED light for prolonged periods while device is on

• During operation, do not cover the ventilation grille found at the rear of device and ensure light is cool before storing

• Do not use or leave device in conditions of extreme heat, severe cold or high humidity

• Unit will display a decrease in brightness when the battery runs low; be sure to replace battery when necessary to avoid affecting recording quality

• When cleaning the device, use only a mild detergent solution and quickly wipe dry with a soft cloth

• Dispose of used batteries, packaging and old devices in accordance with appropriate environmental regulations

PRODUCT OVERVIEW

Filter Mounting Magnets

MOUNTING LIGHT UNIT DIRECTLY ON CAMERA OR TRIPOD

• Ensure that locking collar is fully loosened and slide cold shoe mounting into shoe of camera; rotate collar clockwise to lock light in place securely
• For tripod installation, simply insert 1/4 20 screw found on tripod head into the 1/4 20 threading mount found on bottom of unit; then tighten securely

Note

Light can also be fastened to included ball head mount, which can then be installed on cold shoe found on cameras or similar devices; see ball head mounting instructions

MOUNTING LIGHT UNIT ON BALL HEAD MOUNT

• Included ball head mount is designed to provide user with a 180° tilt/360° rotating angle feature that can be used on both cameras and other devices featuring a cold shoe
• Begin by inserting 1/4 20 screw found atop ball head mount into the 1/4 20 threading found on bottom of LED light unit and fasten securely
• Tighten adjustment locking knob so light unit does not wobble during remainder of mounting process
• Ensure cold shoe foot is firmly secured to ball head mount device and loosen locking collar found on base of ball head device
• Slide entire male cold shoe into female cold shoe of camera or other mounting device; then fasten locking collar securely

INTERLOCKING WITH OTHER LED DEVICES

- Loosen adjustment locking knob by twisting counterclockwise and rotate ball head mount to position light at desired angle; twist locking knob clockwise to hold light unit firmly in position

Note

Cold shoe mount can also be removed to reveal an integrated1/4 20 threading mount

- To reveal ball head mount's integrated 1/4 20 threading mount for fastening to tripod, twist locking ring resting above cold shoe counterclockwise until entire shoe comes out; insert 1/4 20 screw found on tripod head into the 1/4 20 threading mount; then tighten securely

- Ensure that device locking collar is fully loosened and slide cold shoe mounting into interlocking expansion slot of another compatible Genaray LED light; rotate collar counterclockwise to lock in place securely

- Up to 3 compatible Genaray LED light devices can be mounted to the top and sides of each individual light device or mounted in a stacked vertical format for increased illumination

POWERING DEVICE

• Begin by holding fully-charged battery in position over mounting area, leaving only a small gap between conductor contacts found on battery and metal prongs found on unit
• Push battery down and lock into place by sliding it inwards along grooves until an audible click is heard
• Twist the power & dimming switch clockwise to turn LED lights on
• Press the built-in battery level indicator button to instantly view the power remaining in the battery; each indicator circle represents approximately 25% of battery capacity; the showing of 4 lit circles

combined will represent a fully charged battery

Note

For an accurate reading of battery levels, it is best to turn off light unit before using battery level indicator feature

• Rechargeable battery can be removed by firmly pushing down on the battery release button
• The DC input found on rear of device connects directly to the included AC power adapter or car charger and can provide continuous power when battery is low or not working

ADJUSTING FEATURES

• To adjust the 3200K-5600K variable color temperature range, simply rotate color variation knob until desired effect is achieved
• To adjust the flicker-free dimmable features, simply rotate the power & dimming knob until desired effect is achieved
• To install magnetic snap-on diffusion filter, hold diffuser over LED panel with silver magnetized posts facing inwards; then quickly snap it into place

PRODUCT SPECIFICATIONS

Bulb Type: 72 Daylight and 72 Tungsten LEDs

Brightness: 640 lux @ 3'

Color Temperature: 3200K - 5600K

Voltage: 7.4-14.8V

Weight: 0.46 lbs

Dimension: 5.25" × 3.5" × 2"

CUSTOMER SUPPORT

For more information about this product or to contact the Genaray Customer Support Center with any questions, please send your email correspondence to: [e-mail].

ONE-YEAR LIMITED WARRANTY

This GENARAY product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. Genaray's responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at Genaray's discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by Genaray. If the product has been discontinued, Genaray reserves the right to replace it with a model of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, GENARAY MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.

To obtain warranty coverage, contact the Genaray Customer Service Department to obtain a return merchandise authorization ("RMA") number, and return the defective product to Genaray along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser's own risk and expense.

For more information, or to arrange service, visit www.genaray.com or contact us at [e-mail].

© 2014 Genaray LLC. All Rights Reserved.

www.genaray.com

genaray™