Invert 6 - Tent Zempire - Free user manual and instructions

Product Type	Tent
Brand	Zempire
Model	Invert 6
Capacity	6 Person
Pole Configuration	5 color-coded pole sections (RED, BLUE, GREEN, YELLOW, plus one additional)
Inner Tent Material	White fabric
Fly Material	Zempire logo at front
Door Type	Round door (front), U door (rear)
Ventilation	Lower vents and inner door mesh for airflow
Fire Retardant	Yes, fabric treated with fire retardant (not fireproof)
UV Protection	UV light can degrade fabric; avoid extended exposure
Guarantee	2 years against faulty materials or manufacture
Setup Instructions	Peg corners first, then remaining loops; poles through sleeves and secured with pins and c-clips
Guy Ropes	Recommended at 45° angle to ground, always pegged out
Condensation Prevention	Open lower vents and inner door covers; avoid foam mats on floor
Mildew Care	If mildew forms, wash with warm water and soft brush; do not use detergents
Storage	Never store wet; dry completely before packing
Storm Usage	Not designed for storm conditions; take down in strong winds
Country of Testing	Tested in New Zealand
Country of Manufacture	Made with care in China

Frequently Asked Questions - Invert 6 Zempire

How do I reduce condensation inside the tent?

Always open the lower vents and inner door covers to allow airflow. Avoid using foam mats or non-bonded mats directly on the tent floor, as they can trap moisture and cause condensation.

What should I do if mildew forms on the tent?

Wash the affected area with warm water and a soft brush to remove mildew. Do not use soap or detergents, as they may damage the fabric. Dry the tent completely before storing.

How long is the guarantee for the Zempire Invert 6 tent?

The tent comes with a 2-year guarantee from the date of sale against faulty materials or manufacture. It applies only to the original purchaser from an approved retailer and covers reasonable personal camping use.

Can I use the tent in stormy weather?

No, this tent is not designed to withstand storm conditions. It is recommended to take it down during strong winds to prevent damage.

How should I set up the poles?

Assemble the 5 pole sections, ensuring they are fully inserted into the ferrules. Thread the RED poles diagonally through the centre sleeves, then the BLUE (front) and GREEN (rear) poles, and finally the YELLOW pole across the rear. Insert ends into pins and attach c-clips.

Why are guy ropes important?

Guy ropes provide stability and should be pegged out at all times at a 45° angle to the ground. They help prevent the tent from being damaged by wind and keep the fly taut.

Is the tent fireproof?

No, the fabric is treated with a fire retardant but is not fireproof. Do not use open flames inside the tent.

How do I clean the tent?

For general cleaning, use warm water and a soft brush. Avoid soap or detergents. If the tent is wet, dry it completely before packing to prevent mildew. For mildew, follow the same cleaning method.

Can I leave the tent pitched for a long time?

No, prolonged exposure to UV light can damage the fly and shorten the life of the tent. It is best to take it down after use.

What is the best way to peg the tent?

First peg out the four corners of the tent, then peg the remaining loops. Ensure the peg points at the base of each pole are pegged through the webbing loop, not the ring, for a flat floor.

USER MANUAL Invert 6 Zempire

1. Ensure guy ropes are out at all times during use
2. Never pack your tent away wet. If you must take your tent down when wet, ensure that it is dried completely as soon as possible to prevent mildew forming
3. If mildew does form on your tent, wash off with warm water and a soft brush to prevent further growth, do not use soap or detergents
4. Do not use an open flame inside your tent. The fabric has been treated with a fire retardant but is in no way fire proof
5. Clean all pegs and poles before storing
6. This tent is not designed to withstand storm conditions. During strong winds, it is recommended that the tent be taken down
7. Do not leave your tent pitched unnecessarily for extended periods of time, UV light damages the fly and will shorten the life of your tent

Condensation -

It is important that lower vents are opened at all times to reduce the risk of condensation. During humid or damp conditions, it is recommended that inner door covers are opened to expose the mesh layer to allow additional airflow throughout your tent.

Do not use foam swabs or non bonded mats directly on the tent floor. This will cause condensation between the mat and floor and if not dried out can lead to mildew foaming.

2 Year Tent Guarantee -

Please take time to read about the protections we offer you

All our tents come with a guarantee designed to protect you as our valued customer. Flow Imports Ltd, the makers of Zempire Camping Equipment tents, will repair or replace this tent, at their discretion should it fail due to faulty materials or manufacture for a period of 2 years from the date of sale.

The Guarantee is subject to the following conditions:

1. The Guarantee only applies to an original purchaser who purchased this tent from an approved retail outlet
2. The Guarantee does not apply if the tent has been used for anything other than reasonable personal camping use. Commercial use (e.g. rental) or continuous use as a residence are expressly excluded
3. Damage due to normal wear and tear, accident, acts of God, negligence (other than by Flow Imports Ltd), failure by the purchaser to ensure instructions for setting up and care are observed, deterioration due to abnormal exposure to ultraviolet light, insect or mildew attack, or any other cause reasonably beyond the control of Flow Imports Ltd are not covered

4. If redress is sought under the terms of this Guarantee, then the tent must be returned by the purchaser to the outlet from where it was purchased within the Guarantee period, in a clean, dry state and with proof of purchase

5. All transport costs and any other indirect costs are excluded from the Guarantee.

6. Flow Imports Ltd reserves the right to make a reasonable charge for repairs which it determines are not within the scope of the Guarantee

7. The Guarantee does not limit, modify or exclude any rights under any law if doing so would contravene that law or make any part of this Guarantee invalid. However, Flow Imports Ltd: a) excludes (to the extent permitted by applicable law) all conditions and warranties that might otherwise be implied; and

b) limits its liability for breach of any such condition or Guarantee that it cannot exclude together with its liability under the Guarantee, to repairing or replacing the Goods or paying the cost of having the Goods repaired or replaced (at Flow Imports' option).

This tent has been made with meticulous care and attention to detail. Providing it's properly looked after and correctly stored, it will help you enjoy all that nature has to offer for years to come.

Get out more - you owe it to yourself.

For a detailed description of all the features and specifications of this product please visit our website.

WWW.ZEMPIRECAMPING.COM

Tested in New Zealand. Made with care in China

!NVERT6

INVERTSERIES

INSTRUCTIONS

!NVERT6 INVERTSERIES

INSTRUCTIONS

1. Clear your site making sure there are no sharp objects where you are going to pitch you tent. Try to get a site that is as flat as possible. Spread out the inner tent (white). The round door is located at the front, the U door is located at the rear

1. Assemble the 5 pole sections. Ensure that the poles do not snap together. Ensure the pole does not snap together. It is important that the poles are fully inserted into the ferrules. If the ferrules do not connect together correctly they can cause damage when tensioned.

2. Thread the RED poles through the pole sleeves that run diagonally across the centre of the tent. Insert the ends of the poles into the pins located below each pole sleeve. Attach the c-clips around the poles

3. Thread the BLUE pole through the BLUE trimmed pole sleeve at the front and the GREEN pole through the GREEN trimmed pole sleeve at rear of the centre dome you have just created. Insert the pole ends into the pins at the base and clip the c-clips to the frame.
4. Thread the remaining YELLOW pole through the pole sleeve that runs across the rear of the tent. Insert the ends of the poles into the pins located at the rear corners of the tent. Clip the c-clips between the pole sleeve and the pin onto the pole.

Diagram of a 3D structural model with curved and straight lines, no text or symbols present

Diagram of a 3D structural model with curved blue and green arches, showing a magnified inset of a mechanical component (no text or symbols)

Diagram of a 3D wireframe structure with curved elements and an orange arrow pointing to a small black object (no text or symbols present)

1. Firstly peg out the 4 corners of the tent (●), then peg out the remaining peg loops (●). The peg points at the base of each pole should be pegged through the webbing loop rather than the ring. Try to get the floor sitting as flat as possible at each stage.

Diagram of a dome-shaped structure with internal nodes and connecting lines, no text or symbols present

1. Pull the fly over the inner tent. The Zempire logo should be at the front of the tent. Connect the Velcro loops inside the fly around the cut out on the corresponding pole sleeve or directly around the pole.

3D wireframe diagram of a dome-shaped structure with curved internal lines, showing rotational motion and a close-up inset (no text or symbols)

1. Attach the elastic loops over the existing inner pegs. Where there is not existing peg, peg the fly directly into the ground ensuring there is significant space between the inner and fly.

Diagram of a 3D folded structure with red circles highlighting specific points, and an inset magnified view showing a small mechanical component (no text or symbols)

3D illustration of a gray camping tent with red lighting lines (no text or symbols)

1. It is recommended that guy ropes are pegged out at all times and windows are opened whenever possible to allow adequate ventilation. Try to have the guy ropes at a 45^ angle to the ground.