TTL-830UEPC - DJ Equipment ROADSTAR - Free user manual and instructions

Product Type	DJ Turntable
Brand	Roadstar
Model	TTL-830UEPC
Dimensions (W x D x H)	450 x 350 x 100 mm
Weight	5.5 kg
Power Supply	AC 100-240V, 50/60 Hz
Power Consumption	15 W
Playback Speeds	33 1/3, 45, 78 RPM
Pitch Control Range	±10%
Anti-Shock Protection	Yes
Outputs	RCA (Line/Phono), Headphone (3.5 mm)
Inputs	None (built-in preamp)
Includes	Turntable, dust cover, slipmat, 45 rpm adapter, power cable, user manual
Maintenance	Clean with soft dry cloth; avoid liquids
Safety Warnings	Keep away from moisture, heat, and magnetic fields
Spare Parts Availability	Contact Roadstar customer service
Reparability	Service by qualified technician only
General Information	Professional DJ turntable for vinyl playback and scratching

Frequently Asked Questions - TTL-830UEPC ROADSTAR

What is the Roadstar TTL-830UEPC?

The Roadstar TTL-830UEPC is a DJ turntable designed for vinyl playback and scratching, suitable for professional and hobbyist use.

How do I connect the turntable to my sound system?

Connect the turntable using the RCA outputs. Select Phono if your receiver has a phono input, otherwise use Line mode (built-in preamp).

What speeds does the turntable support?

It supports 33 1/3, 45, and 78 RPM via a speed selector switch.

Does it have pitch control?

Yes, the turntable features a pitch control slider with a range of ±10% for beatmatching.

How do I replace the stylus?

Gently remove the old stylus by pulling it forward. Insert the new stylus until it clicks. Ensure the cartridge is properly aligned.

What should I do if the turntable does not spin?

Check the power connection and ensure the belt is not broken. If the belt is loose, replace it. Also verify the speed selector is set correctly.

Can I use this turntable with a computer?

Yes, if your computer has a RCA-to-USB interface or a sound card with RCA inputs. Otherwise, you may need an external USB audio interface.

How do I clean the turntable?

Use a soft dry cloth to wipe the exterior. For the platter and dust cover, use a slightly damp cloth and dry immediately. Avoid liquids near the components.

What accessories are included?

The package includes the turntable, dust cover, slipmat, 45 RPM adapter, power cable, and user manual.

Where can I find spare parts?

Contact Roadstar customer service or visit their official website for authorized spare parts and service centers.

USER MANUAL TTL-830UEPC ROADSTAR

TURNTABLE WITH MP3 PLAYER, ENCO-DING FUNCTION VIA PC AND AUDIO LINE-OUT.

TTL-830UEPC

Instructionmanual

Bedienungsanleitung

Roadstar Management SA, via Passeggiata 7, CH 6883 Novazzano (Switzerland)

Is a registered Trademark of Roadstar S.A. - Switzerland All rights reserved

INDEX

- Your new unit was manufactured and assembled under slot ROADSTINR quality control. Thank you for purchasing our product. Bobin opening the unit, please read this instruction manual carefully. Keep it also handy for further future references.

Simple line drawing of a rectangular object with two small circular markers labeled 9 and 10, no text or symbols present.

WARNINGS

The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

To reduce the risk of electric shock, do not remove the cover. No user serviceable parts inside the unit. Refer all servicing to qualified personnel.

230v\~

This unit operates on 230V \~ 50Hz. If the unit is not used for a long period of time, remove the plug from the AC mains.

This unit must not be exposed to moisture or rain.

The power switch in this unit is mounted on the secondary circuit and does not disconnect the whole unit from the mains in OFF position.

Ensure all connections are properly made before operating the unit.

This unit should be positioned so that it is properly ventilated. Avoid placing it, for example, close to curtains, on the carpet or in a built-in installation such as a bookcase.

Do not expose this unit to direct sunlight or heat radiating sources.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

EnglishEng

TTL-830UEPC

TURNTABLE WITH MP3 PLAYER, ENCODING VIA PC AND RADIO LINE-OUT.

INSTRUCTIONMANUAL

Please read this instruction manual carefully and familiarize yourself with your new Audio system before using it for the first time. Please retain this manual for future reference.

LOCATION OF CONTROLS

1) DUST COVER
2) AC-230V CABLE
3) ON / OFF POWER SWITCH
4) LINE OUT CABLE
5) SPINDLE ADAPTER
6) DISC PLATTER
7) CUEING LEVER
8) TONE ARM LOCK
9) 33 / 45 RPM SELECTOR
10) EJECT BUTTON
11) MAGNETIC PICK-UP
12) USB PORT

CONNECTING TO POWER

Before switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.

For your own safety read the following instructions carefully before attempting to connect this unit to the mains.

This unit is designed to operate on AC 230V 50Hz current only. Connecting it to other power sources may damage the unit.

CAUTION

To prevent electric shock disconnect from the mains before removing cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

SAFETYPRECAUTION

Do not allow this unit to be exposed to rain or moisture.

Mains Supply: 230V 50Hz - AC only

This symbol means that this unit is double insulated. An earth connection is not required.

POWER SUPPLY

Remove the stereo carefully from the box, retaining the packaging for future use (servicing).

AC POWEROPERATION

Connect the plug to a mains power inlet 230V AC \~ 50 Hz.

ASSEMBLING

The belt and turntable platter have been installed properly at factory, but the belt may be loose during transportation. If so, the following procedures will be taken for belt installation by yourself.

A. Remove the rubber mat from the turntable platter and the E ring from the turntable shaft, then release the turntable platter from the shaft
B. Pu t the drive belt on the inner rim of the turntable platter and pull it through the hole
C. Hold the belt with your fingers and place the belt onto the motor pulley as shown in the drawing "Fig. 1".
D. Clip the E ring on the shaft and place the rubber mat onto the turntable platter.

Caution:

1. Make sure that the drive belt is not twisted or distorted.
2. Avoid oil. Oil splashes will make the belt slippery.

Auto Return Reset:

Always do the reset for Auto Return once you move this product. The mechanism of Auto Return will rotate irregularly when moving and it will cause the malfunction of Auto Return. The following steps will reset the mechanism to normal.

1. Place a record on the platter and play it.
2. Manually lever the tone arm and place it to the blank part of the end of the record.
3. The mechanism of Auto Return function will be adjusted properly and the tone arm will automatically return to the arm rest.

Fig. 1

5

TURNTABLEOPERATION

Preparation

Open the Record Player Cover.

Listening to Records

1. Set the power ON/OFF SWITCH (3) to ON position.
2. Place a record on the turntable, over the central spindle. Place the EP adapter over the central spindle when playing 17cm EP records.
3. Set the Speed Selector (5) to 33 or 45 rpm according to the record.
4. Release the tonearm clamp, and remove the protective cap from the stylus.
5. Lift the Tonearm with the Tonearm Lift Lever.
6. Move the tonearm to the beginning of the record, or to the start of a particular track.
7. Gently lower the tone arm onto the record with the Tonearm Lift lever to start playing.
8. When the record is finished the tonearm will automatically stop and return to the rest.
9. To stop manually, lift the tonearm from the record and return it to the rest.
10. To automatically stop the record, press the "EJECT" button (15).
    Notes: Do not stop or turn the platter manually.
    Moving or jarring the turntable without securing the Tonearm clamp could result in damage to the Tonearm. Reinstall the protective cap on the stylus when not in use.

How to suspend play

Setting the cueing lever to the UP position will lift the tone arm and then the play stops.

How to use manual cueing

The cueing lever is used when you want to momentarily interrupt the tone arm. Move the lever gently to the "UP" position to interrupt the playing and to the "DOWN" position to resume playing.

Keep the cueing lever in the down position when you are not using it.

6

EnglishEng

SOFTWARE INSTRUCTION

Before Starting the Software

Make sure that your USB turntable is plugged into the computer and both the computer and the turntable are plugged in and on.

To Install Software (PC)

1. Plug in your turntable to an AC outlet and connect the USB port on the Turntable to the USB port of your computer.
2. Turn on the power switch to your turntable.
3. Windows system will detect a new device and that it is available to use.
4. Insert the CD that came with your USB turntable.
5. Run the file "install audacity-win-1.2.6b.exe" to install Audacity software. Once installed, run the Audacity program.

To Install Software (MAC)

1. Insert the included CD
2. Open the CD icon on the desktop.
3. Drag the installation folder for audacity to your hard drive. We recommend that you move the folder to your "Applications" folder.
4. A window will come up which shows the files copying.
5. EJECT the CD
6. Open "Audacity" from where you moved it to on your hard drive.

Software Configuration

1. Click on Microphone in the drop down menu and select "Stereo Mix"

Figure 1: Select Stereo Mix

1. Select the "Edit" menu and then "Preferences" Select the USB audio device under the "Recording" selection as shown. Select "USB Audio CODEC" to hear the audio while recording.

Note: The USB Turntable may show up with a different name in Windows system.. This may depend on your computer model and operating system. 99% of the time it will contain "USB" in the Name

Figure 2: Select USB Audio Device from Preferences

After complete the above setting, you are ready for recording.

If you are still having difficulty finding the USB Turntable, try to check your system settings or control panel to adjust audio input settings from the sound control panel.

LINEOUTCONNECTION

You can connect the system to your home Hi-fi system by connecting the LINE OUT socket (26) to the auxiliary input socket with a RCA cable (not included).

SPECIFICATIONS

Power Supply

AC:

230V \~ 50Hz

Type Belt drive Manual system

Turntable Speeds 33 1/3 R.P.M. and 45 R.P.M.

Motor DC

E.G. motor

Turntable platter

332 mm diameter

Tonearm

Static balance

Wow & Flutter

0.25 % (JIS WRMS)

Dimensions

Design and specifications are subject to change without notice.

Deutsch

9

SICHERHEITSHINWEISE