IMC82BC - Refrigerator Scandomestic - Free user manual and instructions

Product Type	Undercounter Refrigerator
Model	IMC82BC
Brand	Scandomestic
Dimensions (H x W x D)	82 cm x 59.5 cm x 54.5 cm
Weight	30 kg
Power Supply	220-240 V, 50 Hz
Energy Consumption	Approx. 100 kWh/year
Climate Class	N-ST
Temperature Range	+2°C to +8°C
Defrost Type	Manual
Adjustable Thermostat	Yes
Interior Light	Yes
Reversible Door	Yes
Number of Shelves	3 (glass)
Door Bins	3
Crisper Drawer	Yes
Maintenance	Clean with mild soap; defrost when ice > 5 mm
Safety Features	Stable shelves, proper ventilation
Spare Parts Available	Shelves, door bins, thermostat
Warranty	2 years (standard)

Frequently Asked Questions - IMC82BC Scandomestic

How do I install the Scandomestic IMC82BC refrigerator?

Ensure the fridge is placed on a level surface with at least 10 cm clearance around for ventilation. Connect to a properly grounded outlet. The door can be reversed if needed; refer to the manual for hinge adjustment.

How do I adjust the temperature?

Rotate the thermostat dial inside the fridge. Higher numbers (e.g., 5-7) mean colder temperatures. For normal use, set to 3-4. Wait 24 hours for temperature stabilization.

How do I clean the refrigerator?

Unplug the fridge and remove all contents. Clean interior with a mild detergent and warm water. Avoid abrasive cleaners. Wipe dry before plugging back in.

How do I defrost the freezer compartment?

This model requires manual defrost. When frost exceeds 5 mm, unplug the fridge, remove food, and leave the door open. Place towels to catch melting water. Do not use sharp tools to remove ice.

Why is my refrigerator making noise?

Normal sounds include compressor humming, refrigerant flow (gurgling), and occasional clicks from the thermostat. If noises are loud or irregular, check that the fridge is level and not touching surrounding cabinets.

How energy efficient is this model?

The Scandomestic IMC82BC has an estimated annual energy consumption of 100 kWh, placing it in energy class F (subject to specific market). Proper maintenance and placement can improve efficiency.

Can I reverse the door hinge?

Yes, the door is reversible. You will need a screwdriver and follow the step-by-step instructions in the manual. Keep all parts for reassembly.

What should I do if the refrigerator is not cooling?

Check if the unit is plugged in and the thermostat is set correctly. Ensure the door seals are clean and closing properly. If still not cooling, allow 24 hours after first startup. If problem persists, contact support.

What is the warranty period?

The standard warranty is 2 years from date of purchase. It covers manufacturing defects. Register your product online to validate warranty.

Where can I buy spare parts?

Spare parts like shelves, door bins, and thermostat can be ordered from your retailer or directly from Scandomestic. Use the model number IMC82BC for correct parts.

USER MANUAL IMC82BC Scandomestic

Black plastic laboratory condenser unit with clear glass lid and ventilation slots (no text or symbols visible)

Symbol of a trash bin crossed with no text or numbers, representing waste sorting or disposal (no text present)

Please read this manual book carefully before use and operate according to this manual book

Please keep it well and for your reference.

This manual is original in English.

Proper use

The refrigerated and frozen food cabinet described in this operating manual is intended for storing snacks, cold drinks, dairy products and frozen foods or ice cream.

Do not load the cabinet with non-frozen products and do not try to freeze products in the case.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children should be supervised to ensure that they do not play with the appliance.

Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

WARNING: Keep clear of obstruction all ventilation openings in the appliance enclosure or in the structure for building-in.

WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

WARNING: Do not damage the refrigerant circuit.

WARNING: Do not use electrical appliances inside the food

storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

Proper use only means the use as described above, adhering to the specifications on installation, connection, operation and service. Any other use is regarded as being contrary to specification and is prohibited.

To avoid any damage during the transport or the installation, never tilt the cabinet more than 50^

Safety regulation

Warning: Keep ventilation openings in the appliance enclosure or in the structure clear of obstruction.

Warming: Do not damage the refrigerant circuit.

If the cabinet is filled with refrigerant Propane (R290) please read carefully the attached Safety Instructions. The type of refrigerant is documented in the cabinet's type plate.

Refrigerating units operating on Propane (R290) may not be placed in an area with sources of ignition (e.g. unsealed electrical contacts) or where the refrigerant could gather in the event of a leak. The type of refrigerant is indicated on the cabinet's type plate.

The plug-in refrigerated cabinets as described in this operating manual are designed and manufactured in compliance with the international safety regulations.

Like any electrical appliance, it must be handled with all due care, particularly with consideration to ensuring electrical safety.

To ensure safe operation in all service conditions, the following safety precautions must be observed:

- The device may not be used by persons with limited physical, sensory or mental skills and/or with no experience and/or knowledge.

- Never connect the cabinet to the power supply if it is damaged (in transit or otherwise). When in doubt, contact your Service Organization or dealer.

- Contact your Service Organization if you are in any doubt about electrical connection, working or safety of your plug-in refrigerated cabinet.

- The power plug must be connected in regulation matter and the electrical power supply must be as indicated on the type plate.

- Never work yourself on electrical equipment.

- Electronic and electrical elements (e.g. damaged cable) may only be replaced by a qualified electrician or person with experience in electrical engineering! Safety first!

- If any damage occurs to the power cable, pull the plug to disconnect the cabinet. Please make sure that the cabinet can't be switched on again. Call your local Service Organization.

- Damaged fluorescent tubes, starters and 1 or tube covers must be replaced immediately. Contact your local Service Organization.

- When disconnecting the power plug, always pull on the plug itself and never the cable.

- Remove the cabinet from use if it is not working properly or exhibits any damage. Disconnect the power plug, transfer the merchandise to other cabinets or a cold-room and call your local Service Organization.

Product overview

1 Cabinet opening
2 Front glass
3 Left side panel
4 Advertising nail
5 Evaporator
6 Fan
7 Power supply
8 Thermostat
9 Switch
10 Power cord
11 Return air glass
12 Universal wheel
13 Universal wheel (with brake)

Black plastic laboratory condenser unit with clear glass panel and ventilation slots (no text or symbols visible)

14 Condensing fan
15 Condensing fan screen cover
16 Fan blade
17 Condenser
18 Compressor
19 Right side panel
20 Left wind deflector
21 Right wind deflector
22 LED strip
23 Lower glass door
24 Upper glass door

Installation

Single-row line-up

When cabinets are installed side by side, no distance is required between the end walls of the refrigerated cabinets under normal.

Ambient conditions.

Group installation, back to back When two IMC82BC cabinets are installed back to back, this can be done without a distance between the rear walls.

Requirements for electrical connection

The cabinet s connected by inserting the power plug in a socket (fig. 7).

The cabinet must not be plugged into a multiple outlet power strip (see lig.8) The socket employed must be firmly installed, properly earthed and separately fuse-protected by a 10A-circuit breaker, type C.

Supply voltage and frequency of the socket must be in accordance with the data shown on the type plate of the cabinet. Therefore, the cross-section of the wires must be increased, if necessary. for long wires to the socket. The local utility company's regulations on the power connection (e.g earth-fault protection, additional equipotential bonding, remote control switch etc.) must be observed. If in doubt, consult a qualified electrician.

- Run the power cables so that they are protected from risk of damage and there is no risk of tripping (fig.9).

• Please do not drill in the outer or inner of the cabinet. This might damage the refrigeration circuit.
• If necessary. put the plugs of electrically operated accessories (e.g. the display super structure) into separately secured sockets.
• The power cable may not come into contact with parts over 75°C.

Starting

Measures prior to starting

If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand for at least three hours before being started to allow the lubricating oil to settle in the compressor! Failure to do so can cause total destruction of the compressor refrigerating system.

Setting into operation

• Start the cabinet only if it has been installed as described.
• Plug power plug (1-1) in socket (1-2).
• When selecting the socket, observe the requirements stated in section

- The cabinet must not be plugged into multiple-outlet power strip (see fig.2).

- Switch on remote control switch (fig.2) or provided. Starting is signaled by the low running noise of fans and refrigeration system.

Customer should close the lids properly. if not, condensation might happen.

Specifications

Type		IMC82BC
Length	[mm]	730
Width	[mm]	450
Height	[mm]	900
Display area	[m2]	0.86
Useful capacity	[I]	68
Rated power input	[w]	250
Rated Current	[A]	1.5
Temperature	[°C]	-1~7
Rated Voltage Range	[V]	220-240
Rated Frequency	[Hz]	50

Troubleshooting

Any trouble occurring might be due to a minor problem that you can correct yourself following the instructions below. Do not try any further action if the pointers given cannot solve the problem!

Repairs on the cabinet must be made only by qualified specialists. Incompetent repair work can cause serious personal danger, contact your Service Organization for any repairs needed.

Trouble	Possible cause	Corrective measures
The cabinet does not work (no audible running noise or only fan noise audible).	Automatic evaporator defrosting active or electronic controller witched off.Power plug not connected or remote control switch (where provided) switched off.Fuse blown, power plug or socket defective.Condenser fins fouled.	Not required, as cooling will switch on automatically again.1. Insert power plug properly in or switch remote control switch on.2. Contact your electrician or the Service Organization.3. Perform maintenance.
Cabinet Stopp's running after short operation.	Condenser fins fouled.	Perform maintenance.
Storage temperature is too high.	Automatic evaporator defrosting active.Ambient temperature too high or electronic controller misadjusted.The warm air outlet of another cabinet is directly taken in as air intake.Ventilation slots blocked or covered.Lack of air intake due to obstruction of air intake grille.Condenser fins fouled.	Not required, temporary minor temperature rise during defrosting is normal.Avoid extreme operating environment, readjust storage temperature.Observe single-row line-up and group installationKeep ventilation slots free.Remove any obstacles in the air intake area.Perform maintenance.
Storage temperature is too high.	Misadjustment	Adjust storage temperature in small increments.
Storage temperature is too low.	Drip water gutter under base plate fouled	Clean
Condensation on the sliding glass lids	Wrong close of the sliding lids	Close the lids properly

R290 refrigerant is used for this equipment.

WARNING; Risk of fire / flammable materials

Caution!

Consult repair manual/owner's guide before attempting to install or service this product. All safety precautions must be followed. Dispose of properly in accordance with federal or local regulations. Risk of fire or explosion due to puncture of refrigerant tubing. Follow handling instructions carefully.

Danger!

Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel. Do not use mechanical devices to defrost refrigerator. Do not puncture refrigerant tubing.

Disposal

Symbol of a trash bin crossed with a diagonal line, no text or numbers present

EU regulations require refrigeration product to be disposed of by specialist companies who remove or recycle all gasses, metal and plastic components.

Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of the equipment locally.

All packaging materials should be disposed of in an environmentally friendly way.

The cardboard may be used as scrap paper. The protective foil and the foam cushions are CFC-free.

Do not allow children to play with the packaging and destroy plastic bags safely.

Environmental protection

Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively support us in conserving resources and protecting the environment by returning this appliance to the collection centers (if available).

Compliance

Parts have undergone strict product testing in order to comply with regulatory standards and specification set by international, independent, and federal authorities.

Products have been approved to carry the following symbol:

Black plastic laboratory condenser unit with clear glass lid and ventilation slots (no text or symbols visible)

Symbol of a trash bin crossed with a diagonal line, no text or numbers present

Black plastic laboratory condenser unit with clear glass panel and ventilation slots (no text or symbols visible)

Symbol of a trash bin with crossed lines indicating no waste or restriction, and a solid black rectangle below (no text or labels)

EU declaration of conformity

Name and address of the manufacturer or his authorised representative:

Scandomestic A/S

Linåvej 20

8600 Silkeborg

Denmark

This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):

Scandomestic A/S

Linåvej 20

8600 Silkeborg

Denmark

References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:

EN ISO 17050-1: 2004

Additional Information

Object of the declaration

(identification of product allowing traceability. It may include a colour image of sufficient clarity to enable the identification of the product)

Black and white photo of a glass-walled refrigerator with ventilation slots (no visible text or symbols)

Model number(unique identification of the product):	IMC82BC
Type	Impulse Cooler
Brand	Scancool
Outside colour	Black

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

scandomestic

Denmark · CVR. No.: 29774242

Phone: [phone]

[e-mail]

DK

Adgang til professionel reparation, såsom internetsider, adresser, kontaktoplysninger: Model nr.: IMC82BC

Access to professional repair, such as internet webpages, addresses, contact details.

Model no: IMC82BC

Aftersales service station list:

Address	Linåvej 20 . 8600 Silkeborg . Denmark	QR code
Contact Number	0045 7242 5571
Website	www.scandomestic.dk
Relevant information for ordering spare parts, directly or through other channels provided by the manufacturer, importer or authorised representative;			www.scandomestic.dk
The minimum period during which spare parts, necessary for the repair of the appliance, are available; (years)			8
defined in Regulation EU 2019/2018 by means of a weblink that links to the model information as stored in the product database or a link to the product database and information on how to find the model identifier on the product.)			www.scandomestic.dk

Note: The address or contact phone number of the service site is subject to change without prior notice. Please confirm whether the service station is a directly affiliated one of our company when requiring services.

SE