32Z012 - Blender Zelmer - Free user manual and instructions

Product Type	Blender
Brand	Zelmer
Model	32Z012
Power Consumption	600 W
Capacity	1.5 L
Speed Settings	2 speeds + pulse
Jar Material	Plastic (BPA-free)
Blade Material	Stainless steel
Dimensions (H x W x D)	40 x 20 x 20 cm
Weight	2 kg
Cord Length	1.2 m
Voltage / Frequency	220-240 V / 50-60 Hz
Safety Features	Overload protection, non-slip feet
Dishwasher Safe Parts	Jar, lid, and blade assembly (top rack)
Spare Parts Available	Jar, lid, seal ring, blade unit
Warranty	2 years

Frequently Asked Questions - 32Z012 Zelmer

Can I blend hot liquids in the Zelmer 32Z012 blender?

It is not recommended to blend hot liquids directly as pressure can build up. Allow them to cool to room temperature before blending. If you must blend warm liquids, remove the center cap to allow steam to escape.

How do I clean the blender jar and blades?

The jar, lid, and blade assembly are dishwasher safe on the top rack. For hand washing, use warm soapy water and a soft brush. Avoid abrasive cleaners to prevent scratching.

What is the maximum capacity for dry ingredients?

For dry ingredients like grains or nuts, do not exceed half of the jar capacity (about 750 ml) to ensure proper blending and avoid motor strain.

Can I crush ice with this blender?

Yes, the Zelmer 32Z012 can crush ice. Use the pulse function in short bursts for best results. Add a little water to help the process.

What should I do if the blender stops working during use?

The blender has overload protection. If it stops, unplug it, let it cool for 15-20 minutes, reduce the load, and try again. If it persistently fails, contact customer support.

Are replacement parts available?

Yes, spare parts such as the jar, lid, seal ring, and blade unit can be ordered through Zelmer's official website or authorized service centers.

Is the blender jar BPA-free?

Yes, the jar is made from BPA-free plastic, making it safe for food contact.

What is the warranty period?

The Zelmer 32Z012 comes with a 2-year warranty covering manufacturing defects. Retain your receipt for proof of purchase.

Can I blend frozen fruits directly?

Yes, but for best results, cut frozen fruits into small chunks and use the pulse mode to avoid jamming. Add some liquid if needed.

How do I replace the blade assembly?

To replace the blade assembly, unscrew the retaining nut from the bottom of the jar (if applicable) or remove the entire base. Ensure the new blade is securely tightened to prevent leaks. Refer to the manual for specific instructions.

USER MANUAL 32Z012 Zelmer

Green layered dessert garnished with lemon slices and fresh red berries, accompanied by a small ice cube illustration (no text or symbols)

Black and white photo of a modern blender with a blue control knob (no visible text or symbols)

PITATOZ KIN JPYTOKANIA4MINDER KEJUCHOWYTyp 322112	4-8	4H07/14 AT STASIATKEL THER MEER32/11/1 Topa	13-15	16	JNCTPATRA 1A 1907PEAKWIKUK P KANATyp 322112	23-24
NAVO K POUPTISTOLOW MEERSTyp 322112	7-9	RUTTURELA DE UTUCEBLENDER STATYP Typ 322112	16-18	17	HOPY 6315 1000CTBHINTWIKCEP 3 HAUEROTyp 322112	25-28
NAVO K OBBLAHSTOLOW MEERSTyp 322112	10-12	HOPY 2000 TO 3000TALAWEBEIGEPTyp 322112	19-21	18	USER RAYDALSTAND BLENDERTyp 322112	25-31

32Z012

Mikser klelichowy

Stand blender

The text in the source image is illegible due to extreme pixelation and distortion. No characters, numbers, or symbols can be reliably extracted.

Deposcealing was rieproneone prazo: 3 min.1s.

Important safety instructions

Read the whole instruction for use before you start using your stand blender.

The stand blender is intended for domestic usage only. In case it is used for gastronomic business purposes, warranty terms and conditions change.

Connect the appliance to 230 V mains supply.

Always place the appliance on flat, plain surface.

always unplug the appliance when it is not in use and before cleaning.

Do not unplug by pulling on cord.

The supplying cord shall not be hanged over the edge of the table or board, nor touch any hot surface.

Do not operate the appliance if the cord, the housing or the handle is visibly damaged. In such a case, return the appliance to a service center.

If the non-detachable part of the cord is damaged, it should be replaced by the producer or at a proper service point or by a qualified person in order to avoid any hazards.

The appliance can only be repaired by qualified service personnel. Improper servicing may cause a serious hazard to the user. In case of defects please contact a qualified service center.

Do not immerse motor housing in water or any other liquid; do not use it in bathroom and outdoors.

Press "OFF" button, before you remove the lid of the jug and remove the jug from the motor housing, wait until the blades stop completely.

Do not use stand blender without feeder opening stopper.

Do not fill the jug in with boiling liquids.

Do not put your hands inside the jug, even if it is removed for cleaning, as the cutting blades are still dangerous – very sharp.

Do not put any objects (spoon, etc.) into the jug, when the blender is connected to power supply.

Keep the jug blender and supplying cord away from hot surfaces and burners.

it is possible, store the stand blender away from direct sun radiation and glow-like light.

Never store with lid closed on the blender jug. Damp the lid gasket with water before usage, and insert the lid on the jug.

Do not overflow the jug. In case the liquid gets under the motor housing, it can be vacuumed into the motor, causing its damage.

Do not fill the jug over 1500 ml mark – in such case, the content of the jug can lift the lid when the motor starts up

After 2 minutes operation stop the appliance for at least minute to let the motor cool down. You can repeat this cycle maximum10 times.

Do not operate when the jug is empty, as it can get overheated.

Do not wash the cutting blades directly with hand.

use the soft brush for washing metal parts, especially the sharp blades.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The temperature of mixed ingredients should not exceed 60°C.

Make sure you understand well above mentioned instructions.

Specifications

You can find the appliance technical data on the name plate. Admissible time of non-stop operation: 3 minutes.

An interval between repeated operations: 10 minutes.

Maximum noise level: 80 dB/A.

The stand blender is built in II class of insulation

It does not require connecting to mains supply socket with earthing.

The stand blender meets the requirements of effective standards.

The appliance meets the requirements of the following directives:

Low Voltage Device (LVD) - 2006/95/EC.

Electro- Magnetic Compatibility (EMC) - 2004/108/EC.

The product is marked with CE symbol on the name plate.

Outline (Fig. A)

1 Lid sieve

2 Speed I

3 ICE

4 ON/OFF

5 Speed II

6 CLEAN/PULSE

7 Feeder opening stopper

8 Lid

9 Blender jug

10 Motor housing

11 Control panel

12 Anti-slip flange

13 Blocking ring

14 Blades

15 Gasket

Handling and operation (Fig. B)

Preparation for operation

Before first usage (or after long storage) wash the jug (9), lid (8) and feeder opening stopper (7) in hot water with washing-up liquid, rinse and dry well. Keep your hands away from cutting blades (14) – they are sharp.

Operation manual

① Place the motor housing (10) on dry, firm, and horizontal surface, near mains supply outlet and out of the reach of children.

Arrange the supplying cord so that it does not hang from the table or board and it can not be pulled or dragged by accident.

② Connect the plug into the mains supply outlet.
③ Place the jug (9) so, that the protrusions at the bottom part of the jug (9) were fitted with the protrusions in top part of motor housing (10).
④ After proper assembling of the jug, the blue highlight shall glow around the control panel (11).

The handle of the blender jug (9) shall be placed on the right side of the appliance.

⑤ Put the ingredients into the jug (9).
⑥ Do not fill in over 1500 ml marked on the blender jug (9). In such case, the content of the jug can lift the lid (8) when the motor starts up.
⑦ Before you use the stand blender, assemble the lid (8) on the blender jug (9) so, that its protrusion was in line with the protrusion in the jug.

ATTENTION: Before you insert the lid (8) moisture the lid gasket with water.

⑧ Insert the lid overlay (7) into the inlet in the lid (8) so that the protrusions of the overlay enter the cuts in the lid inlet and turn it left or right until it moves.

Do not start the stand blender without the feeder opening stopper (1), especially, when you use solid ingredients. They can be thrown out of the opening.

⑨ Switch mixing on pressing speed I (2), speed II (5) or CLEAN/PULSE (6).
⑩ Press ON/OFF switch to turn off the appliance.

Operating with speed I or speed II, the appliance is switched off automatically after 2 minutes.

⑪ CLEAN/PULSE function

• Dressing CLEAN/PULSE (6) button shall cause short operation with maximum speed.
  Do not operate longer than 3 minutes, otherwise it can get overheated.
  you need to add some new ingredients during blender operation, turn and lift feeder opening stopper (7), feed

the ingredients into the opening, then replace the stopper again (7) and turn it left or right until it runs.

Make sure, that the ingredients you add, shall not increase the capacity inside the jug exceeding 1500 ml marking on the jug (9).

⑫ ICE function

• check if the stand blender is clean, before you use it for crushing ice. Otherwise wash it thoroughly with clean water. Any residues of washing agent can influence the taste of crushed ice and shall cause that the drink we add the ice to, shall loose its taste.
  case you want to crush ice, use 6 to 10 ice cubes (max. 2 cm) in given time, and then add 15 ml (1 spoon) fresh cold water.
  assemble the lid (8) including overlay (7) on the appliance and press ICE switch.

ICE feature operates for 30 seconds, then the appliance switches off automatically.

Do not try to crush the ice without adding some water into the jug.

Press the lid (8) with one hand during ICE feature is on.

After operation

To switch off the stand blender press and hold ON/OFF switch for 3 seconds, until the blue highlight around the control panel (11) is off.

Hold the motor unit(10) with one hand, catch the jug handle with the other hand and remove it from the motor unit (10) turning it counter-clockwise.
Remove the lid (8) from the jug (9).
Onplug the appliance from the mains supply outlet when it is not in use.

Cleaning and maintenance (Fig. C)

Clean after operation as soon as possible, to prevent the pulp accumulation inside the jug (9).

① Pour approximately 1 liter of water to the blender jug (9) and start-up the appliance for approximately 30 seconds and hold the CLEAN/PULSE button.
② Then empty the blender jug (9), turn it upside-down and dry.
③ If necessary, clean the jug (9), lid (8), feeder opening stopper (7) and blades (14) in warm water with wash-up liquid.

When rinse it under clean running water and dry.

you left the jug for longer time without cleaning and some particles glued to the jug inner, use nylon brush.
We do not recommend cleaning the jug (9), blades (14), lid (8) and feeder opening stopper (7) in dish washer. Aggressive cleaning agents applied in such device can influence negative the surface conditions.

④ Clean the outsider of the motor housing (10) with damp, gentle cloth.

ATTENTION: Do not immerse the motor housing (10) in water or other liquid.

Do not clean the outside of the housing (10) with aggressive detergents such as emulsion milk or pastes, etc. They can remove information graphic symbols.
Do not clean the transparent jug (9) with harsh sponges or clothes.
After washing dry thoroughly all the parts of the appliance.

Cutting unit disassembling

Onplug from the mains supply outlet.

Empty the jug (9).

■ remove the lid (8) from the blender jug (9). Turn the blender jug (9) „upside down” and place on the flat and firm surface.

Turn the blocking ring counter clockwise. Remove carefully with a gasket.

ATTENTION: The cutting blades are sharp. Handle them carefully.

Cutting unit assembling

Turn the blades upside down in order to assemble them and insert at first the gasket at the jug opening flange (9) and blades inside the jug (9).
Insert blocking ring and turn it clockwise until it runs. Make sure that the blocking ring is screwed to the jug (9). It influences the tightness of the connection.
After assembling, turn the jug (9) upside down and place it on the motor housing (10) so, that the protrusions in bottom part of the jug (9) are fitted with the protrusions top part of the motor housing (10).

The handle of the blender jug (9) shall be placed on the right side of the appliance.

Ecology – environment protection

Each user can protect the natural environment. It is neither difficult nor expensive.

In order to do it: put the cardboard packing into recycling paper container; put the polyethylene (PE) bags into container for plastic.

When worn out, dispose the appliance to particular disposal centre, because of the dangerous elements of this appliance, which can be hazardous for natural environment.

Do not dispose into the domestic waste disposal!!!

The manufacturer/importer does not accept any liability for any damages resulting from unintended use or improper handling. The manufacturer/importer reserves his rights to modify the product any time in order to adjust it to law regulations, norms, directives, or due to construction, trade, aesthetic or other reasons, without notifying in advance.

Notes