Q: No audio signal detected on channel 1

First, check the physical connections: Make sure the XLR cable is properly connected to the XLR input of channel 1 Check the integrity of the cable (no internal break) Test with another XLR cable to rule out a cable defect Check the gain potentiometer: The gain potentiometer (item 2) should be gradually turned to the right. If it is at minimum, no signal will pass. Turn it gradually to bring the input level to an adequate level. Observe the indicator LEDs: The Signal LED (item 3) should light up when the signal reaches the input of channel 1. If it does not light up, the problem lies with the upstream connections (audio source or cable) Ensure that the Protect LED (item 8) is not continuously lit, which would indicate overheating or failure Check the mode configuration: The Mode selector (item 13) should be set according to your use (Stereo, Mono, or Bridge) The Limiter switch (item 14) should be in the ON position for amplifier protection Test your audio source: Connect another audio source (MP3 player, television, etc.) to confirm whether the problem comes from your initial source or the amplifier.

Q: How do I connect my laptop to the JBSYSTEMS MIX 5.2?

The JBSYSTEMS MIX 5.2 is a fully analog mixing console: it does not have a direct USB connection and does not have a dedicated line input for laptops on its front panel. To connect your Surface Laptop or any other laptop, you need to use one of its existing inputs located at the back: Solution 1: Via RCA inputs (cinch) - The simplest Use a 3.5 mm to stereo RCA adapter cable (mini jack to 2x RCA) to connect the audio output of your laptop Connect this cable to the RCA inputs of channels 2-5 (labeled “LINE IN” at the back). These channels also have switchable phono inputs if needed Adjust the volume fader of the corresponding channel and the Master fader (A/B zones) to set the level Use the 3-band equalization controls (bass, mid, treble) to adjust the sound to your needs Solution 2: Via a USB audio interface (more professional) Get a small USB audio interface (like Behringer UMC202, Focusrite Scarlett Solo) with RCA or XLR outputs Connect it to the Surface Laptop via USB-C Connect the outputs of the interface to the RCA line inputs or XLR inputs (channels 1-5) of the MIX 5.2 This approach offers better audio quality and more connection flexibility Note: The XLR inputs of the 5 channels are intended for balanced microphones but can also accept line signals via a USB audio interface.

Question 1

No audio signal detected on channel 1

Accepted Answer

First, check the physical connections:

Make sure the XLR cable is properly connected to the XLR input of channel 1
Check the integrity of the cable (no internal break)
Test with another XLR cable to rule out a cable defect

Check the gain potentiometer:

The gain potentiometer (item 2) should be gradually turned to the right. If it is at minimum, no signal will pass. Turn it gradually to bring the input level to an adequate level.

Observe the indicator LEDs:

The Signal LED (item 3) should light up when the signal reaches the input of channel 1. If it does not light up, the problem lies with the upstream connections (audio source or cable)
Ensure that the Protect LED (item 8) is not continuously lit, which would indicate overheating or failure

Check the mode configuration:

The Mode selector (item 13) should be set according to your use (Stereo, Mono, or Bridge)
The Limiter switch (item 14) should be in the ON position for amplifier protection

Test your audio source:

Connect another audio source (MP3 player, television, etc.) to confirm whether the problem comes from your initial source or the amplifier.

Question 2

How do I connect my laptop to the JBSYSTEMS MIX 5.2?

Accepted Answer

The JBSYSTEMS MIX 5.2 is a fully analog mixing console: it does not have a direct USB connection and does not have a dedicated line input for laptops on its front panel.

To connect your Surface Laptop or any other laptop, you need to use one of its existing inputs located at the back:

Solution 1: Via RCA inputs (cinch) - The simplest

Use a 3.5 mm to stereo RCA adapter cable (mini jack to 2x RCA) to connect the audio output of your laptop
Connect this cable to the RCA inputs of channels 2-5 (labeled “LINE IN” at the back). These channels also have switchable phono inputs if needed
Adjust the volume fader of the corresponding channel and the Master fader (A/B zones) to set the level
Use the 3-band equalization controls (bass, mid, treble) to adjust the sound to your needs

Solution 2: Via a USB audio interface (more professional)

Get a small USB audio interface (like Behringer UMC202, Focusrite Scarlett Solo) with RCA or XLR outputs
Connect it to the Surface Laptop via USB-C
Connect the outputs of the interface to the RCA line inputs or XLR inputs (channels 1-5) of the MIX 5.2
This approach offers better audio quality and more connection flexibility

Note: The XLR inputs of the 5 channels are intended for balanced microphones but can also accept line signals via a USB audio interface.

Question 3

How do I connect the BEAT 4 USB to my computer?

Accepted Answer

The BEAT 4 USB from JB Systems has 2 bidirectional USB 2.0 connections at the back of the device (USB1 for channel CH3, USB2 for channel CH4). These connections allow for audio transmission at 44.1 kHz / 16 bit and are compatible with Windows and macOS without requiring additional drivers.

Connection procedure: Connect a standard USB cable (maximum length of 3 meters) from one of the two USB ports on the BEAT 4 USB to a free USB port on your computer. Make sure to turn off the BEAT 4 USB before making the connection, then turn it on once the cable is connected. Your PC or Mac will automatically detect the BEAT 4 USB as a sound card and recognize it immediately without further intervention.

Bidirectional advantage: The USB connections of the BEAT 4 USB are bidirectional, meaning you can simultaneously play music from your computer and record your mix. This unique feature allows you to:

Play music from your computer via the USB channels
Mix this music with other sources (CD, vinyl, line)
Record your final mix directly to your computer via the same USB connection

Input configuration: Once connected, select the corresponding USB input (USB for CH3 or CH4) on the front of the BEAT 4 USB using the input source selector for each channel. Then adjust the input level with the Gain slider until you reach approximately 0 dB on the PFL VU meter, then feed the music into your usual mixing channels.

Recording the mix: To record your mix, you can use the Record output of the BEAT 4 USB, which transmits the same signal as the Master outputs but is not influenced by the Master volume or balance controls. This provides stable recording quality independent of your real-time mixing adjustments.

Question 4

How to use the DMX protocol with the JBSYSTEMS LED QUADRA BEAM projector as a beginner?

Accepted Answer

The DMX protocol is a standardized system that allows remote control of projectors and lighting effects from a single controller. With the JBSYSTEMS LED QUADRA BEAM, you have three ways to use this equipment according to your needs: in standalone mode without a controller, in master/slave mode to synchronize multiple devices, or in full DMX mode for precise control.

To get started with DMX on the LED QUADRA BEAM, begin with the physical connection. You will need a good quality 3-pin XLR symmetrical cable. Connect the cable from your DMX controller to the male XLR input of the projector (pin 1 = ground, pin 2 = negative signal, pin 3 = positive signal). You can chain multiple projectors by connecting the female XLR output of one device to the input of the next.

Before connecting the DMX cable, you need to set the starting DMX address on your LED QUADRA BEAM using the DIP switches located at the back of the device. The address depends on the mode you choose. If you are using the projector in standalone mode (without a controller, activated by music), set the DMX address to 001 (only toggle DIP switch number 1 to ON, the others to OFF). For master/slave mode with multiple devices, set the master to address 000 and the slaves to 001, 007, 013, etc., following the intervals. In pure DMX mode with a controller, use addresses 001, 002, 003 in 1-channel mode or 001, 007, 013 in 6-channel mode.

The LED QUADRA BEAM offers two DMX control modes suitable for both beginners and advanced users. The 1-channel mode is the simplest: a single DMX channel allows you to select one of the 12 pre-programmed programs or to turn the effect on/off (DIP switch number 10 to ON). The 6-channel mode provides full control over the 4 clusters of LEDs with channel 1 for program selection, channel 2 for the ultra-fast strobe, channels 3, 4, 5 to control the individual intensity of the red, green, and blue LEDs, and channel 6 for the overall dimmer (DIP switch number 10 to OFF).

To configure the DIP switches correctly, note that the first 9 correspond to binary values (1, 2, 4, 8, 16, 32, 64, 128, 256). You can combine them to obtain any address between 001 and 051. For example, for address 005, toggle switches number 1 and 3 to ON (1 + 4 = 5). Test your configuration with your DMX controller: the device should respond immediately to the received commands. If you have trouble finding the correct address, refer to your DMX controller's manual, as the starting address completely depends on the controller used.

In summary, for a beginner: first plug in your LED QUADRA BEAM, set the appropriate DMX address with the DIP switches, then connect the XLR cable from your controller. Start with the 1-channel mode which is very intuitive, then progress to the 6-channel mode once you master the basics. Use quality balanced microphone cables and ensure that all devices are properly powered before configuring the DMX address.

Question 5

How to connect and operate multiple JBSYSTEMS LED DEVIL projectors together with a DMX controller?

Accepted Answer

To operate multiple JBSYSTEMS LED DEVIL projectors together with a DMX controller, follow these steps:

1. Connecting the projectors in series

Link the projectors together using DMX cables. Each projector has a DMX input and output, allowing them to be connected in series (daisy chain). Ensure that all projectors are powered correctly.

2. Setting DMX addresses

Each projector must have a unique DMX address to be controlled individually. Use the buttons or the menu on the projector's housing to set these addresses. For example, for three projectors, you can assign addresses 1, 2, and 3.

3. Connecting to the DMX controller

Plug the DMX controller into the DMX input of the first projector in the chain. Check that the controller is powered on and ready to send DMX signals.

4. Programming and control

Use the controller to program the desired effects, such as colors, transitions, strobe effects, etc. Each projector will respond to commands corresponding to its DMX address.

5. Testing and adjustments

Test the setup to ensure that all projectors respond correctly. If necessary, adjust the DMX addresses or settings on the controller to achieve the desired result.

By following these steps, you will be able to effectively synchronize and control multiple JBSYSTEMS LED DEVIL projectors with a DMX controller.

Question 6

How to perform a reset on the JBSYSTEMS CLUB LASER 7?

Accepted Answer

To perform a reset on your JBSYSTEMS CLUB LASER 7, follow these simple steps:

Turn off the device using the main switch.
Unplug the power cable from the electrical outlet to completely cut off the power.
Wait about 10 to 15 seconds to allow the internal circuits to fully discharge.
Plug the power cable back into the electrical outlet.
Turn the device back on using the switch.

This procedure restarts the device and may resolve temporary malfunctions. If you wish to perform a complete factory reset, this may require specific manipulation through the device menus, but this function is not always available on all models.

If you experience persistent issues after this simple reset, it is advisable to check the connections and ensure that the firmware is up to date if applicable.

User manual JBSYSTEMS : user manuals and guides in PDF

Models JBSYSTEMS most viewed

Browse manuals JBSYSTEMS by appliance type

Recent questions about devices JBSYSTEMS