Q: How to regularly oil the cutting block of the PS 54 CC shredder?

To extend the lifespan of your OLYMPIA PS 54 CC , it is important to regularly oil the cutting block. This maintenance ensures optimal cutting and prevents premature blade clogging. Required oil: Use exclusively a special oil for document shredders provided by Olympia Business Systems. Do not use other types of oils or spray oils, which may severely damage the device. To obtain this special oil, contact Olympia's direct support line. Oiling procedure: Coat a sheet of white paper with the special oil in a crosshatch pattern. Set the rotary switch to Auto . Insert the oiled sheet into the feed slot. The oil-soaked paper is automatically fed in and lubricates the cutting block. Maintenance frequency: Oil the cutting block at regular intervals to maintain the optimal performance of your shredder and extend its lifespan.

Q: How to insert paper into the OLYMPIA CPD 3212 S printer calculator?

Before you begin: make sure to use an original OLYMPIA thermal paper roll with a width of 57 mm and a maximum diameter of 80 mm (reference 06.840.0200). Never use low-quality paper or a reused roll, as this could damage the printer. Steps to insert the paper: Install the roll holder: Locate the roll holder inside the paper compartment, usually above or at the back of the device. Position the roll: Place the paper roll on the roll holder so that it unwinds from the bottom . The paper should come out from underneath the roll. Turn on the calculator: Before inserting the paper, power on the device using the power switch (I/O). Guide the paper: Take the end of the paper and insert it into the rear slot marked with an arrow until it reaches the stop (the back of the slot). Advance the paper: Press the paper feed button (usually marked with an arrow) to feed the paper further into the device until it comes out of the print slot. Important points to remember: never print without paper, do not pull the paper while the printer is operating, and pay attention to markings indicating the end of the roll. When the paper is nearing its end, change the roll immediately to avoid any malfunction. If print quality decreases, also change the ink roll (reference 06.840.0134).

Question 1

How to regularly oil the cutting block of the PS 54 CC shredder?

Accepted Answer

To extend the lifespan of your OLYMPIA PS 54 CC, it is important to regularly oil the cutting block. This maintenance ensures optimal cutting and prevents premature blade clogging.

Required oil: Use exclusively a special oil for document shredders provided by Olympia Business Systems. Do not use other types of oils or spray oils, which may severely damage the device. To obtain this special oil, contact Olympia's direct support line.

Oiling procedure:

Coat a sheet of white paper with the special oil in a crosshatch pattern.
Set the rotary switch to Auto.
Insert the oiled sheet into the feed slot. The oil-soaked paper is automatically fed in and lubricates the cutting block.

Maintenance frequency: Oil the cutting block at regular intervals to maintain the optimal performance of your shredder and extend its lifespan.

Question 2

What should I do if my OLYMPIA PMR 1612 walkie-talkie is not working?

Accepted Answer

If your OLYMPIA PMR 1612 walkie-talkie is not working, here are several steps to check to identify and resolve the issue:

1. Check the power supply

Make sure the battery is properly charged. To do this, place the devices in the charging base and let them charge for about 8 hours. During charging, the red LEDs should remain lit.
To turn on the device, press and hold the power button for about 3 seconds. The screen should light up and display the channel as well as the battery level.

2. Check the channel settings

Ensure that all communicating devices are set to the same main channel.
Also check that the sub-channel (or privacy code) is identical on all devices, as a difference can prevent communication.

3. Test the communication

To transmit, press and hold the PTT (Push To Talk) button, usually red, then speak near the microphone.
Make sure the other device is turned on and within communication range.

If after these checks the problem persists, it may be a hardware defect or a more specific issue requiring technical assistance.

Question 3

How to insert paper into the OLYMPIA CPD 3212 S printer calculator?

Accepted Answer

Before you begin: make sure to use an original OLYMPIA thermal paper roll with a width of 57 mm and a maximum diameter of 80 mm (reference 06.840.0200). Never use low-quality paper or a reused roll, as this could damage the printer.

Steps to insert the paper:

Install the roll holder: Locate the roll holder inside the paper compartment, usually above or at the back of the device.
Position the roll: Place the paper roll on the roll holder so that it unwinds from the bottom. The paper should come out from underneath the roll.
Turn on the calculator: Before inserting the paper, power on the device using the power switch (I/O).
Guide the paper: Take the end of the paper and insert it into the rear slot marked with an arrow until it reaches the stop (the back of the slot).
Advance the paper: Press the paper feed button (usually marked with an arrow) to feed the paper further into the device until it comes out of the print slot.

Important points to remember: never print without paper, do not pull the paper while the printer is operating, and pay attention to markings indicating the end of the roll. When the paper is nearing its end, change the roll immediately to avoid any malfunction. If print quality decreases, also change the ink roll (reference 06.840.0134).

Question 4

Why does my OLYMPIA A 2024 laminator not respond to the micro setting?

Accepted Answer

If your OLYMPIA A 2024 laminator does not respond to the micro setting, here are several points to check to resolve this issue:

1. Check the power supply

Make sure the device is properly plugged in and that the outlet is working. A poor connection or unstable power supply may prevent the control from responding.

2. Reset the device

Turn off the laminator, unplug it, wait a few minutes, then plug it back in and turn it on. This may reset the electronic components and resolve a temporary blockage.

3. Check the temperature and operating mode

Ensure that the temperature is set correctly and that the micro mode is activated properly. Incorrect settings may prevent the micro function from activating.

4. Inspect the laminating materials

Use laminating sheets suitable for the model and ensure they are inserted correctly. Improper positioning may block operation.

If the problem persists after these checks, it may be a technical defect requiring professional intervention.

User manual OLYMPIA : user manuals and guides in PDF

Models OLYMPIA most viewed

Browse manuals OLYMPIA by appliance type

Recent questions about devices OLYMPIA