Q: What does the error code Er 09 mean on the TELEFUNKEN TFIK78EDS10X cooker and how can it be resolved?

The error code Er 09 on the TELEFUNKEN TFIK78EDS10X cooker generally indicates a problem related to the temperature probe. This code may appear if the probe is defective or if there is a faulty electrical connection. How to resolve the error code Er 09: Unplug the device: Cut the power to the cooker by unplugging it or turning off the circuit breaker for a few minutes to reset the system. Check the connections: Ensure that all electrical connections, especially those of the temperature probe, are secure and free from corrosion or damage. Power the device back on: Plug the cooker back in and turn it on to check if the error code persists. If the code Er 09 continues to display after these checks, it is likely that the temperature probe is defective and needs to be replaced. In this case, it is advisable to contact a qualified professional to carry out this repair safely.

Question 1

How to refill the rinse aid (Klarspüler) if the machine is currently running on the TELEFUNKEN TFGS60SI10A++?

Accepted Answer

If you have started a wash cycle and then noticed that the rinse aid (Klarspüler) is low, here’s how to safely refill it on your TELEFUNKEN TFGS60SI10A++:

Procedure

Stop the current program by pressing the On/Off button. The machine will interrupt the cycle and drain the water.
Open the door once the stop is complete and access the rinse aid compartment.
Fill the Klarspüler reservoir up to the indicated mark.
Close the door and press the On/Standby button (button 3) again to restart the program.

Good to know: The dishwasher will automatically resume the cycle from the step where it was interrupted. There is no risk in stopping the appliance to perform this operation - it is designed for this purpose by the manufacturer.

Question 2

Why is the program flashing but the TELEFUNKEN TFGS60SI10A++ dishwasher not starting?

Accepted Answer

If the program is flashing but the machine does not start, first check these simple points:

Door closed properly - Make sure the door is securely locked. An incomplete lock will prevent starting even if the program is selected.
Water supply - Check that the water supply tap is open and that the inlet filter is not blocked by debris or limescale.
Drain hose - Ensure that the drain hose is not bent, twisted, or clogged. A blocked drain can prevent starting.
Pump filter - Clean the filter located at the bottom of the inner tub to ensure no debris is obstructing the pump.

If after these checks the flashing persists and the machine still does not start, this may indicate a specific error code. In this case, refer to the error code table in your manual to identify the exact malfunction.

Question 3

What does the error code Er 09 mean on the TELEFUNKEN TFIK78EDS10X cooker and how can it be resolved?

Accepted Answer

The error code Er 09 on the TELEFUNKEN TFIK78EDS10X cooker generally indicates a problem related to the temperature probe. This code may appear if the probe is defective or if there is a faulty electrical connection.

How to resolve the error code Er 09:

Unplug the device: Cut the power to the cooker by unplugging it or turning off the circuit breaker for a few minutes to reset the system.
Check the connections: Ensure that all electrical connections, especially those of the temperature probe, are secure and free from corrosion or damage.
Power the device back on: Plug the cooker back in and turn it on to check if the error code persists.

If the code Er 09 continues to display after these checks, it is likely that the temperature probe is defective and needs to be replaced. In this case, it is advisable to contact a qualified professional to carry out this repair safely.

Question 4

Why does my TELEFUNKEN DPF 15002 digital photo frame blink on startup but never fully start?

Accepted Answer

If your TELEFUNKEN DPF 15002 digital photo frame flashes or blinks on startup without ever starting properly, it may indicate a problem related to power, software, or hardware. Here are some steps to try to resolve this issue:

1. Check the power supply

Make sure the frame is properly plugged into a working electrical outlet.
Try a different outlet or a compatible power cable to rule out a power fault.

2. Inspect the memory card

If you are using a memory card (SD or USB), remove it and then reinsert it properly.
Try turning on the frame without the memory card to check if the issue is with it.

3. Perform a reset

If the frame has a reset button, use it to restore factory settings.
Otherwise, unplug the frame for at least 5 minutes to allow for an electrical reset, then plug it back in.

4. Check for signs of hardware damage

Examine the frame for any visible damage or overheating.
An internal issue may require technical intervention.

If none of these solutions allow your photo frame to start, it is likely that the problem is of a more complex hardware or software nature. In this case, professional repair or replacement may be necessary.

Question 5

Why is the end indicator flashing on the TELEFUNKEN TFGS60SI10A++ dishwasher?

Accepted Answer

The flashing end indicator on your TELEFUNKEN TFGS60SI10A++ dishwasher may indicate several situations:

1. End of wash cycle

The flashing may simply signal that the wash cycle is complete. You can then open the door and remove your dishes.

2. Door not properly closed

If the dishwasher door is not properly closed, the end indicator may flash to alert you. Check that the door is securely locked.

3. Water supply issue

A water supply issue, such as insufficient pressure or a clogged inlet filter, can cause this flashing. Ensure that the water supply is correct and that the filter is clean.

4. Drainage issue

If the dishwasher is unable to drain water, the indicator may flash. Check that the drain hose is not blocked and that the pump filter is clean.

5. Error signal

The flashing may also indicate an error code related to a malfunction. If other indicators are flashing or if you hear beeping, this may help identify the fault.

In summary, a flashing end indicator is a signal of attention that may correspond to the end of the cycle or a problem requiring verification. Check the door, water supply, drainage, and be attentive to other signals to accurately diagnose the cause.

Question 6

Why does my TELEFUNKEN DPF10333 digital photo frame display a single static photo without changing automatically?

Accepted Answer

If your TELEFUNKEN DPF10333 digital photo frame displays a single static photo without changing automatically, several causes may be responsible:

1. Check slideshow mode

Make sure the slideshow function is enabled. If the frame is set to display a single image, it will not cycle through the photos automatically.

2. File compatibility

Check that the stored photos are in a compatible format (e.g., JPEG, PNG). Unsupported formats may prevent automatic changing.

3. Storage space

If the frame's memory is full or saturated, it may block the slideshow. Try freeing up space by deleting unnecessary images.

4. Power issues

A power issue may affect normal operation. Check that the frame is properly plugged in or that the battery is sufficiently charged.

5. Restarting the frame

A simple restart can resolve temporary bugs. Turn off the frame, unplug it for a few seconds, then turn it back on.

If the problem persists after these checks, it may be a hardware or software defect requiring more in-depth technical assistance.

Question 7

What does the 'Files' icon displayed on the TELEFUNKEN DPF 7331 digital photo frame mean?

Accepted Answer

The 'Files' icon (or file manager) displayed on the main screen of the TELEFUNKEN DPF 7331 digital photo frame allows access to an integrated file explorer. This icon is used to manage and organize multimedia content stored on the internal memory of the frame or on connected memory cards and USB drives.

To use this function, press the 'Left/Right' buttons on your remote control to select the 'Files' icon on the main screen, then press 'Enter' to access the file manager.

From this space, you can perform the following operations:

Browse and view photo files (JPEG, BMP formats), videos (MPEG4, AVI, 3GP, MOV, MJPEG), and music (MP3, WAV, OGG, WMA) stored on your device or on external media.
Copy individual files from your memory cards (SD, SDHC, MMC, MS, MS Pro, MS Duo, XD) or your USB drive to the internal memory of the frame (2 GB available).
Delete files one by one from the internal memory of the frame.
Use the 'Up/Down' buttons on the remote control to select files and the 'Copy/Del' button to copy or delete.

The file manager is particularly useful for organizing your content before starting a slideshow or playing videos and music. Note: files copied via this manager are not automatically resized to the frame's resolution (800 x 600 pixels). If you want to copy multiple files at once with automatic resizing, prefer the thumbnail selection mode.

Question 8

How to delete photos on a TELEFUNKEN DPF8335 or DIAMOND DPF 10333 digital photo frame?

Accepted Answer

To delete photos on your TELEFUNKEN DPF8335 or DIAMOND DPF 10333 digital photo frame, you have two methods depending on your needs.

Method 1: Deleting one photo at a time via the file manager

Press the Exit button on your remote control as many times as necessary to display the media selection screen. Using the Left/Right buttons on the remote, select the Files icon and press Enter. Then select the photo to delete using the Up/Down buttons on the remote, and press the Copy/Del button. The screen will display a confirmation message "Delete file? Yes/No". Choose the desired option and press Enter. Your file is then permanently deleted from the internal memory.

Method 2: Deleting multiple photos via thumbnail mode

This method is recommended if you want to delete a selection or all photos at once. Press the Exit button as many times as necessary to display the media selection screen. Select Internal Memory using the Left/Right buttons and press Enter. Then select the photo mode with the Left/Right buttons and press Enter (the slideshow will start). Press Exit again to access thumbnail mode (miniature display of photos). Press the Copy/Del button: the screen will display "Delete?" with two options "Selection" or "All". Choose the desired option and press Enter. The thumbnails will then appear with a checkbox in the upper left corner of each image. Select the photos to delete using the Left/Right buttons on the remote and pressing Enter on each photo (a checked box will appear). If you chose "Delete All", all thumbnails will be automatically checked. Once your selection is complete, press Copy/Del and then Enter. The screen will again display a confirmation message "Delete?". Select your choice with the Up/Down buttons and press Enter. Your photos are now deleted from the internal memory of the frame.

Important: Deletion is permanent and irreversible. Photos are completely erased from the internal memory of the frame. Make sure to back up important photos before deleting them. Note that you can also delete personal folders located in the predefined directories in the same way.

User manual TELEFUNKEN : user manuals and guides in PDF

Models TELEFUNKEN most viewed

Browse manuals TELEFUNKEN by appliance type

Recent questions about devices TELEFUNKEN