KE91XE - Four encastrable SMEG - Notice d'utilisation et mode d'emploi gratuit

Type d'appareil	Hotte aspirante
Usage prévu	Usage domestique
Installation minimale	Distance de 650 mm entre la plaque de cuisson et la hotte
Hauteur d'installation	Peut être installée à une hauteur inférieure selon dimensions
Alimentation électrique	Doit correspondre à la plaque de cuisson
Mise à la terre	Obligatoire pour appareils de classe I
Conduit d'évacuation	Minimum 120 mm de diamètre
Longueur du conduit	Doit être la plus courte possible
Ne pas connecter à	Conduits d'évacuation de combustibles (chaudières, cheminées)
Utilisation avec autres appareils	Assurer une aération suffisante pour éviter le refoulement
Pression négative maximale	0,04 mbar
Orientation de la flamme	Ne pas diriger la flamme vers le fond de la hotte
Surveillance	Surveiller les filtres et la température
Sécurité enfants	Surveillance nécessaire, ne pas laisser jouer avec l'appareil
Entretien	Nettoyer les filtres régulièrement, remplacer si nécessaire
Nettoyage	Utiliser un chiffon humide et un détergent neutre
Précautions	Débrancher avant maintenance

FOIRE AUX QUESTIONS - KE91XE SMEG

Comment régler la température du SMEG KE91XE ?

Pour régler la température, tournez le bouton de contrôle de température situé sur le panneau avant. Les températures varient généralement de 0°C à 10°C.

Que faire si le SMEG KE91XE ne refroidit pas correctement ?

Vérifiez que l'appareil est branché et que la prise fonctionne. Assurez-vous également que les bouches d'aération ne sont pas obstruées et que la porte est bien fermée.

Comment nettoyer l'intérieur du SMEG KE91XE ?

Utilisez un chiffon doux et humide avec un peu de savon doux. Évitez les produits abrasifs qui pourraient endommager les surfaces.

Y a-t-il une fonction de dégivrage sur le SMEG KE91XE ?

Oui, le SMEG KE91XE dispose d'une fonction de dégivrage automatique pour le réfrigérateur. Assurez-vous de retirer les aliments pendant le processus.

Quelle est la capacité du SMEG KE91XE ?

Le SMEG KE91XE a une capacité de réfrigération d'environ 300 litres, ce qui convient à une utilisation familiale.

Comment changer l'ampoule du SMEG KE91XE ?

Pour changer l'ampoule, débranchez l'appareil, retirez le cache de l'ampoule à l'intérieur du réfrigérateur et remplacez l'ampoule par une ampoule de type équivalent.

Le SMEG KE91XE émet un bruit étrange, que faire ?

Un bruit peut être normal lors de l'utilisation, mais si le bruit persiste, vérifiez que l'appareil est de niveau et que rien n'est en contact avec les ventilateurs.

Comment ajuster les étagères du SMEG KE91XE ?

Les étagères peuvent être ajustées en les retirant et en les repositionnant dans les supports à la hauteur souhaitée.

Où trouver le numéro de série du SMEG KE91XE ?

Le numéro de série se trouve généralement à l'intérieur de la porte, sur une étiquette collée sur le cadre.

Comment utiliser la fonction de congélation ?

Pour utiliser la fonction de congélation, placez les aliments dans le compartiment de congélation et réglez la température à un niveau approprié, souvent -18°C.

MODE D'EMPLOI KE91XE SMEG

The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650~mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm . The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
• In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks.
• If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled.

USE

• The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flambe under the range hood; risk of fire
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  Children should be supervised to ensure that they do not play with the appliance.
• "CAUTION: Accessible parts may become hot when used with cooking appliances."

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

FIXING OF THE HOOD UNDER THE CABINET

• To drill the cabinet follow the indications given in the dimensional drawing in the chapter which regards hood dimensions.
• To fix the hood onto the cabinet use the 44,4 ~mm long screws inserting and tightening them from the inside of the cabinet.

Connection to air outlet

AIR OUTLET IN THE DUCTING MODE

When installing the hood in ducting version, basing on the installer's choice, a rigid or a flexible pipe is used in order to connect the hood to the air outlet piping.

• Insert the flange on the hood body outlet.
• Open the metal grid and make sure that the conversion knob is in the ducting position.
• Connect the hood to the air outlet piping with a pipe.
  Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.
• Remove the charcoal filter if present.

AIR OUTLET IN THE RECYCLING MODE

• Open the metal grid and make sure that the conversion knob is in the recycling position.
• Place the charcoal filter. The charcoal filter is not supplied together with the hood. (Hoods with two motors needs to be equipped with two charcoal filters).

INSTRUCTIONS ON OPENING THE SUCTION GRILL

• Slide the side stops towards the centre of the hood and at the same time pull the grill forwards.
• The grill will drop down, turning on the two rear pins, and will remain hanging from them.
• To disconnect it completely, pull the right hand part of the grill forwards slightly so that the pin comes out of the grill through the slot formed on the body of the hood.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm..

L Light Switches the lighting system on and off
V Speed Sets the operating speed of the extractor:

0.Motor Off.

1. Low speed, used for a continuous and silent air change in the presence of light cooking vapour.
2. Medium speed, suitable for most operating conditions given the optimum treated air flow/noise level ratio.
3. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods.

GREASE FILTER

Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. Special attention should be taken to keep the grease filter clean at all times and the charcoal filter (recirculation model) should be replaced regularly. To remove filters for subsequent cleaning and replacement first open the metal grille panel.

This retain the solid grease particles. It is fitted onto the reverse side of the lower grille panel and can be either of a synthetic material or metallic. Maintenance of the grease filter varies according to the type used: synthetic grease filters should not be washed and should be replaced every three months. The metal grease filters should be washed once a month in hot water using mild detergent or liquid soap. It should not be bent and should be left to dry before being refitted. The filter is easily removed from grille by pushing the spring wire clips to one side and removing.

CHARCOAL FILTER

In the recycling mode the charcoal filter absorbs smells and odours. The charcoal filter cannot be cleaned and should be replaced at least every six months or more frequently if the hood is used consistently.

To replace the charcoal filter, support the filter with one hand, remove the round disk through the centre of the charcoal filter and rotate it till the filter will come away.

Replace by reversing the operation.

WARNING! It is a possible fire hazard if the filters are not cleaned and replaced as recommended.

WORKTOP ILLUMINATION

If a lamp fails to function at any time, open the metal grille panel and check that the lamp is fully screwed into the holder.

When changing the lamp, an identical replacement must be fitted to ensure a safe working of the hood.

CLEANING

The metalwork should be cleaned regularly, at least once a month, using household cleaners and polish. Never use abrasives.