2305 - Tableau d'affichage Quartet - Notice d'utilisation et mode d'emploi gratuit

Type de produit	Tableau d'affichage mural
Marque	Quartet
Modèle	2305
Dimensions approximatives	90 x 120 cm
Poids approximatif	3 kg
Matériau de surface	Liège ou feutre textile
Couleur du cadre	Aluminium ou bois (selon version)
Type de montage	Mural (fixations incluses)
Alimentation	Aucune (passif)
Fonctions principales	Affichage de documents, notes, photos par punaises ou adhésifs
Entretien et nettoyage	Dépoussiérer avec un chiffon doux sec ; ne pas utiliser de produits liquides
Sécurité	Vérifier la solidité de la fixation murale ; ne pas surcharger
Pièces détachées et réparabilité	Pièces non disponibles séparément ; tableau non réparable
Contenu de l'emballage	Tableau, kit de fixation murale, notice d'installation
Garantie	2 ans

FOIRE AUX QUESTIONS - 2305 Quartet

Comment fixer le tableau d'affichage Quartet 2305 au mur ?

Utilisez le kit de fixation fourni. Percez des trous aux emplacements repérés, insérez les chevilles, vissez les supports muraux, puis accrochez le tableau en alignant les fixations arrière.

Quel type de punaises ou adhésifs utiliser sur le tableau Quartet 2305 ?

Utilisez des punaises standard, des épingles ou des adhésifs repositionnables légers. Évitez les adhésifs permanents qui pourraient endommager la surface.

Puis utiliser des feutres ou marqueurs sur le tableau ?

Non, le Quartet 2305 est un tableau d'affichage en liège ou feutre, non effaçable. Les marqueurs permanents tacheraient la surface.

Comment nettoyer le tableau d'affichage Quartet 2305 ?

Dépoussiérez régulièrement avec un chiffon doux et sec. Pour les taches, utilisez un chiffon légèrement humidifié avec de l'eau, puis séchez immédiatement. N'utilisez pas de produits chimiques.

Quelle est la capacité de charge maximale du tableau ?

La surface peut supporter des documents et objets légers (quelques feuilles, photos). Évitez de suspendre des objets lourds ou de surcharger le tableau pour ne pas déformer la surface ou endommager la fixation.

Le tableau Quartet 2305 est-il réversible ou à double face ?

Non, il s'agit d'un tableau mural simple face. La face arrière est pleine et non destinée à l'affichage.

Comment remplacer la surface d'affichage si elle est usée ?

La surface n'est pas remplaçable séparément. En cas d'usure importante, il est recommandé de remplacer l'ensemble du tableau.

Le cadre du Quartet 2305 est-il en aluminium ou en bois ?

Le modèle 2305 existe en version cadre aluminium (argenté) ou bois (selon référence). Consultez l'étiquette du produit pour confirmer.

Puis-je installer le tableau horizontalement et verticalement ?

Oui, le tableau peut être fixé dans les deux orientations grâce aux fixations adaptées. Assurez-vous de bien le centrer et de le niveler.

Où télécharger la notice complète du Quartet 2305 ?

La notice complète est disponible gratuitement au format PDF sur le site notice-facile.com. Utilisez le lien de téléchargement sur la page du produit.

MODE D'EMPLOI 2305 Quartet

EURO ALUMINUM FRAME BOARD – Mounting Instructions

*NOTE – For Dry-Erase Boards:

Before mounting board to wall, please refer to instructions in "Accessory Kit" to attach the marker tray to the board frame.

Step 1 Step 2

Determine board location. To position top hanging brackets, mark center hole of hanger 6" from outside edge of board and 1-3/8" down from top of board (A). Drill holes for each hanger in marked locations using a 1/4" drill bit. Tap anchor into hole flush to wall with metal "teeth" firmly embedded. Turn screw clockwise to expand metal legs. Stop when strong resistance is felt and legs are fully expanded.

Turn screw counter-clockwise to remove screw from anchor and re-insert through hanging bracket into wall anchor (B). Tighten firmly. Holding the board at (approx.) 15° angle, place the channel in the back of the frame over the wall hangers. Lower the board so it is flush to the wall (C).

Remove plastic corner caps (D), mark wall through top hole of each corner (E). Remove board from wall and drill holes in marked locations using a 1/4" drill bit. Install wall anchors as indicated in Step #1 (F). Re-hang board and insert screw through plastic corner and into wall anchor. Tighten firmly. Replace corner caps by pressing into place over the screws. (L-Brackets & Truss Head Screws are not required.)

ALUMINUM FRAME BOARD – Mounting Instructions

*NOTE – For Dry-Erase Boards:

Before mounting board to wall, please refer to instructions in "Accessory Kit" to attach the marker tray to the board frame.

Step 1

Determine board location. To position top hanging brackets, mark center hole of hanger 6" from outside edge of board and 7/8" down from top of board (A). Drill holes for each hanger in marked locations using a 1/4" drill bit. Tap anchor into hole flush to wall with metal "teeth" firmly embedded. Turn screw clockwise to expand metal legs. Stop when strong resistance is felt and legs are fully expanded.

Turn screw counter-clockwise to remove screw from anchor and re-insert through hanging bracket into wall anchor (B). Tighten firmly. Holding the board at (approx.) 15° angle, place the channel in the back of the frame over the wall hangers. Lower the board so it is flush to the wall (C).

Step 2

To position bottom "L" brackets, mark wall 1-5/8" up from bottom of board 6" from each outside edge (D). To position top "L" brackets, mark wall 1-5/8" down from top of board and a 1/4 of the board width from each outside edge. Drill holes in marked locations using a 1/4" drill bit. Insert wall anchors and mount "L" brackets as indicated in Step #1 (E). Hang board and mark frame through hole in each "L" bracket. Remove board and drill pilot hole at each mark with 1/8" drill bit. Re-hang board and insert #8 x 1/2" truss head screw through each "L" bracket and into pilot hole in frame (F). Tighten firmly.

WOOD FINISH FRAME BOARD – Mounting Instructions

*NOTE – For Dry-Erase Boards:

Before mounting board to wall, please refer to instructions in "Accessory Kit" to attach the marker tray to the board frame.

Step 1

Determine board location. To position top hanging brackets, mark center hole of hanger 6" from outside edge of board and 2-1/4" down from top of board (A). Drill holes for each hanger in marked locations using a 1/4" drill bit. Tap anchor into hole flush to wall with metal "teeth" firmly embedded. Turn screw clockwise to expand metal legs. Stop when strong resistance is felt and legs are fully expanded.

Insert screws through hanging brackets into the wall anchor (B). Tighten firmly. Place the channel in the back of the frame over the wall hangers. Push top of frame down until board is fully engaged on hangers (C).

Step 2

To position bottom "L" brackets, mark wall 2-1/2" up from bottom of board 6" from each outside edge (D). To position top "L" brackets, mark wall 2" down from top of board and a 1/4 of the board width from each outside edge. Drill holes in marked locations using a 1/4" drill bit. Insert wall anchors and mount "L" brackets as indicated in Step #1 (E). Hang board and mark frame through hole in each "L" bracket. Remove board and drill pilot hole at each mark with 1/8" drill bit. Re-hang board and insert #8 x 1/2" truss head screw through each "L" bracket and into pilot hole in frame (F). Tighten firmly.

ACCESSORY PAGE CLIP

- Applies to all boards

Hardware Kit

Dry-Erase and Bulletin Board Installation Instructions

Illustration of a flat-screen monitor with a mesh pattern on the screen and a magnified inset showing a circular detail (no text or symbols)

ACCO Brands

300 Tower Parkway

Lincolnshire, IL 60069-3640

www.quartet.com

www.acco.com