Q: How to remove and store the drainage hose of the HISENSE APC09QC air conditioner?

Preparation and removal of the hose: Before removing the drainage hose, unplug the HISENSE APC09QC air conditioner or disconnect its power supply for your safety. Locate the primary drainage outlet at the back of the unit, where the flexible drainage hose is currently attached. Turn the blind fitting (connector) located at the end of the hose counterclockwise until it completely detaches. Draining and drying: Once the hose is detached, completely drain any residual water by slightly tilting the unit or unscrewing the primary drainage cap to let the water flow out. For long-term storage, run the air conditioner in Fan Only mode for about 12 hours to dry it completely before proceeding to store it. Cleaning and preparing for storage: Inspect the hose to ensure it does not contain any stagnant water or debris. If necessary, rinse it with clean water and let it dry completely before storing. Ensure that the hose has no cracks, permanent bends, or damage that could reduce its effectiveness for the next use. Coiling and storage: Carefully coil the drainage hose in regular loops without bending or pinching it, as this could damage it. Store the hose in a dry place, away from direct sunlight and extreme temperatures. Keep the blind fitting attached to the hose or store it in a safe place nearby for easy reinstallation. Note that the flexible hose provided with your HISENSE APC09QC air conditioner has a standard length allowing flexible installation according to your setup.

Question 1

What is the diameter of the drainage hose for the HISENSE APC09QC air conditioner?

Accepted Answer

The manual for your HISENSE APC09QC air conditioner mentions a flexible drainage hose provided with the unit, allowing you to place the air conditioner at a distance of 60 to 170 cm from the window or door.

However, the exact diameter of the hose is not specified in the documentation provided with this model. In practice, HISENSE portable air conditioners generally use a hose with an interior diameter of 15-16 mm (approximately 5/8 inch), but this information is not confirmed for your APC09QC model.

To know the precise diameter:

Measure the diameter of the hose directly on your unit using a caliper or a flexible measuring tape.
Contact HISENSE support providing your model number (APC09QC) to obtain the exact specification.

Question 2

How to activate the cooling mode on the HISENSE APC12QC air conditioner?

Accepted Answer

To activate the cooling mode on your HISENSE APC12QC air conditioner, use the remote control by following these steps:

Press the MODE button several times until you see the cooling symbol flashing on the indoor unit's screen.
Select the Cooling mode from the available modes: Cooling, Dry, Fan Only, or Heating.
Set the temperature between 16°C and 30°C by pressing the UP (increase) or DOWN (decrease) buttons. You increase or decrease the temperature by 1°C with each press.
Adjust the fan speed by pressing the FAN button to choose between Auto, High, Mid, or Low. The Auto speed automatically adjusts the fan according to the ambient temperature.

Important: Do not confuse Cooling mode with Dry mode. Dry mode dehumidifies the air but does not cool the room. Cooling works optimally when the ambient temperature is between 21°C and 35°C.

Quick cooling: For immediate intensive cooling, press the SUPER button. The unit automatically sets the fan speed to high and the temperature to 16°C. To exit SUPER mode, press any button on the remote control except Timer On, Timer Off, Clock, Dimmer, Ifeel, and Swing.

Note: When changing modes, the air conditioner may not respond immediately. Wait 3 minutes before restarting the unit. Once the desired temperature is reached, the unit automatically adjusts its operation to maintain this setting.

Question 3

How to remove and store the drainage hose of the HISENSE APC09QC air conditioner?

Accepted Answer

Preparation and removal of the hose: Before removing the drainage hose, unplug the HISENSE APC09QC air conditioner or disconnect its power supply for your safety. Locate the primary drainage outlet at the back of the unit, where the flexible drainage hose is currently attached. Turn the blind fitting (connector) located at the end of the hose counterclockwise until it completely detaches.

Draining and drying: Once the hose is detached, completely drain any residual water by slightly tilting the unit or unscrewing the primary drainage cap to let the water flow out. For long-term storage, run the air conditioner in Fan Only mode for about 12 hours to dry it completely before proceeding to store it.

Cleaning and preparing for storage: Inspect the hose to ensure it does not contain any stagnant water or debris. If necessary, rinse it with clean water and let it dry completely before storing. Ensure that the hose has no cracks, permanent bends, or damage that could reduce its effectiveness for the next use.

Coiling and storage: Carefully coil the drainage hose in regular loops without bending or pinching it, as this could damage it. Store the hose in a dry place, away from direct sunlight and extreme temperatures. Keep the blind fitting attached to the hose or store it in a safe place nearby for easy reinstallation. Note that the flexible hose provided with your HISENSE APC09QC air conditioner has a standard length allowing flexible installation according to your setup.

User manual HISENSE Air Conditioning : user manuals and guides in PDF

Models HISENSE Air Conditioning most viewed

Other categories HISENSE

Recent questions about Air Conditioning HISENSE