Question 1

How to change the bulb of the THERMOR EQUATEUR 2 radiator?

Accepted Answer

To change the bulb of your THERMOR EQUATEUR 2 radiator, follow these simple steps:

1. Safety first

Always unplug the device from the electrical outlet before any intervention to avoid any risk of electric shock.

2. Access the bulb

Locate the cover or panel that protects the bulb. On the EQUATEUR 2 model, it may be secured with screws or clips. Carefully remove it using a screwdriver if necessary.

3. Remove the faulty bulb

Once the cover is removed, gently unscrew or unclip the used bulb to take it out.

4. Install the new bulb

Get a bulb compatible with your model (check the manufacturer's technical specifications). Insert it into the socket and secure it by screwing or clicking it in place depending on the type of bulb.

5. Reattach the cover

Replace the cover or protective panel, ensuring it is properly secured with screws or clips to guarantee safety and proper functioning.

6. Check the operation

Plug the radiator back in and turn it on to check that the new bulb works correctly.

By following these steps, you will ensure a safe and effective replacement of the bulb in your THERMOR EQUATEUR 2.

Question 2

How to set the temperature on the weekly programming of the Thermor Équateur 2 radiator?

Accepted Answer

To set the temperature on the weekly programming of your Thermor Équateur 2 radiator, follow these precise steps:

1. Access the programming menu

Turn on your radiator and press the Menu or Program button to enter the weekly programming settings.

2. Select the day to program

Use the directional arrows to navigate to the day of the week you wish to configure.

3. Set the desired temperature

Once the day is selected, you will see the programmable time slots. For each time slot, use the arrows to increase or decrease the desired temperature.

4. Program the time slots

If your model allows it, set different time slots (morning, day, evening, night) with specific temperatures suited to your needs.

5. Confirm the settings

After setting the temperature for each time slot, confirm your choices by pressing the OK or Confirm button.

6. Repeat for other days

Repeat the same process for each day of the week where you want to customize the programming.

7. Exit the menu

Once all settings are made, exit the menu to return to normal display. Your radiator will now apply the programmed temperature according to the defined days and time slots.

These settings allow you to optimize your comfort while saving energy through precise temperature management.

Question 3

Why does the control panel of my THERMOR EQUATEUR 2 radiator light up briefly and then turn off, and the radiator does not start?

Accepted Answer

If the control panel of your THERMOR EQUATEUR 2 radiator lights up briefly and then turns off, and the radiator does not start, several causes may explain this behavior. Here’s how to identify and resolve the issue.

First, check the power supply. Make sure the radiator is properly plugged into a functional electrical outlet. Test the outlet by plugging in another device to confirm that it is delivering power. Also, check that the circuit breaker in your electrical installation has not tripped and is properly engaged. If you have a load shedding device to manage consumption peaks, ensure that it has not cut off the heating supply.

Unplug the radiator for a few minutes. This operation performs a complete electronic reset. After 2 to 3 minutes, plug the device back in. Upon the first power-up, the panel should light up, then after a few moments display the day, time, and default set temperature (19°C). This normal behavior shows that the device is initializing correctly.

Check that you are not in standby mode. If the radiator displays “OFF” and then turns off, it is intentionally going into standby. To turn on the radiator, press the activation button to switch to Comfort or Eco mode. The panel should remain lit and display the set temperature as well as the heating icon if the ambient temperature is below the defined setting.

Check the thermostat position and programming. Ensure that the selected heating mode is either Comfort or Eco, and not Frost Protection. If your radiator is connected to an external programmer or pilot wire, make sure the programmer is properly engaged in its housing and functioning correctly (check the condition of the batteries and fuse). If you are in programming mode, verify that the programmer is set to Comfort mode for the current day.

Wait 6 hours before assessing operation. During the first heating, a slight odor may appear: this corresponds to the evacuation of traces related to manufacturing and disappears after a few moments. Additionally, the EQUATEUR 2 radiator requires a minimum of 6 hours for the temperature to stabilize. This is normal: your radiator operates with thermal inertia and gradually adapts to detected absences from the first week.

Check the installation conditions. Ensure that the radiator is not located in a draft that would disrupt its regulation. The ventilation grilles should not be obstructed. Also, check that the device is not directly under a fixed power outlet.

If after these checks the problem persists, it is likely that the radiator requires technical intervention. Have the power supply voltage of the device checked by an electrician, or contact THERMOR customer service mentioning the reference and serial number of the device (these are located on the rating label on the right side of the radiator).

User manual THERMOR Electric heater : user manuals and guides in PDF

Models THERMOR Electric heater most viewed

Other categories THERMOR

Recent questions about Electric heater THERMOR