Q: How to connect the Smev FO311 oven to gas?

Gas pipe connection: The connection of the gas inlet pipe to the Smev FO311 oven must be made only using a rigid metal pipe and sealed fittings. A flexible pipe can be used provided it is always inspectable, protected from contact with the heated parts of the burner, protected against any stress (twisting, pulling, crushing), protected from moving parts, and does not exceed 1.5 m in length. Types and pressures of gas: The FO311 oven can operate with two types of gas. For butane (G30) , the required pressure is 28 to 30 mbar. For propane (G31) , the required pressure is 30 to 37 mbar depending on the conditions. Check the identification label on the oven to know the type of gas it has been set for, as well as the exact required pressure. Installation of gas bottles: The bottles must be placed in the designated compartment in an upright position. They must be equipped with a valve and a pressure regulator, and their access must not be obstructed. Ensure that the replacement of the bottles can be done easily and without obstacles. Leak check: After making the connection, check for any leaks in the circuit using a non-corrosive fluid (such as an approved electronic leak detector). Do not use a soap and water solution or open flames for this check, as it would pose a fire risk. Important safety note: Do not attempt to make the connection yourself if you are not trained in gas installations. For a permanently or semi-permanently installed appliance, consult a qualified professional who will comply with local safety standards.

Q: Is the Smev FO311 oven a gas oven?

Yes, the Smev FO311 oven is a gas oven. It operates exclusively on gas (propane G31 or butane depending on your installation country) and does not have electric heating elements for cooking. The type of gas to be used is clearly indicated on the label attached to the back of the device and on the packaging. Thermal powers: The oven develops a power of 1.2 kW (87 g/h) in oven mode, and 1.6 kW (116 g/h) in grill mode. These characteristics allow for rapid temperature rise and even cooking. Gas supply: Gas bottles must be placed vertically in the dedicated compartment, equipped with a valve and pressure reducer. The connection of the inlet pipe must be made only using a rigid metal pipe with sealed fittings, or a specific flexible pipe. This installation must comply with local safety standards. Ignition: The device ignites with a match or gas lighter. To produce the flame, press the control button fully, turn it to the desired position (1 to 6 for the oven, or GRILL for the grill), and then simultaneously ignite the burner. Hold the button down for a few seconds to stabilize the flame. Flame control: With propane, the inner dart of the flame should be blue with a sharp outline. This aspect ensures correct combustion and optimal operation of the device. Gas safety: In case of a gas smell, open the windows, immediately evacuate the area, and close the bottle valve without operating any electrical switches or opening any open flames. To check for leaks, use an approved electronic detector or a non-corrosive product (never use soapy solution or open flame).

Question 1

How do I turn on the Smev FO311 oven?

Accepted Answer

To turn on the Smev FO311 oven, follow these steps:

Make sure the oven is properly connected to the gas source and that the gas valve is open.
Turn the temperature control knob to the desired position.
Press the built-in ignition button or, if the oven does not have one, use a long match or lighter to ignite the burner.
Hold the ignition button down for a few seconds to allow the flame to stabilize.
Release the button and check that the flame stays lit.

Precautions: Always work in a well-ventilated area and be cautious when handling gas. If you have difficulty lighting the oven, it is recommended to check the connections or call a professional.

Question 2

How to connect the Smev FO311 oven to gas?

Accepted Answer

Gas pipe connection: The connection of the gas inlet pipe to the Smev FO311 oven must be made only using a rigid metal pipe and sealed fittings. A flexible pipe can be used provided it is always inspectable, protected from contact with the heated parts of the burner, protected against any stress (twisting, pulling, crushing), protected from moving parts, and does not exceed 1.5 m in length.

Types and pressures of gas: The FO311 oven can operate with two types of gas. For butane (G30), the required pressure is 28 to 30 mbar. For propane (G31), the required pressure is 30 to 37 mbar depending on the conditions. Check the identification label on the oven to know the type of gas it has been set for, as well as the exact required pressure.

Installation of gas bottles: The bottles must be placed in the designated compartment in an upright position. They must be equipped with a valve and a pressure regulator, and their access must not be obstructed. Ensure that the replacement of the bottles can be done easily and without obstacles.

Leak check: After making the connection, check for any leaks in the circuit using a non-corrosive fluid (such as an approved electronic leak detector). Do not use a soap and water solution or open flames for this check, as it would pose a fire risk.

Important safety note: Do not attempt to make the connection yourself if you are not trained in gas installations. For a permanently or semi-permanently installed appliance, consult a qualified professional who will comply with local safety standards.

Question 3

Is the Smev FO311 oven a gas oven?

Accepted Answer

Yes, the Smev FO311 oven is a gas oven. It operates exclusively on gas (propane G31 or butane depending on your installation country) and does not have electric heating elements for cooking. The type of gas to be used is clearly indicated on the label attached to the back of the device and on the packaging.

Thermal powers: The oven develops a power of 1.2 kW (87 g/h) in oven mode, and 1.6 kW (116 g/h) in grill mode. These characteristics allow for rapid temperature rise and even cooking.

Gas supply: Gas bottles must be placed vertically in the dedicated compartment, equipped with a valve and pressure reducer. The connection of the inlet pipe must be made only using a rigid metal pipe with sealed fittings, or a specific flexible pipe. This installation must comply with local safety standards.

Ignition: The device ignites with a match or gas lighter. To produce the flame, press the control button fully, turn it to the desired position (1 to 6 for the oven, or GRILL for the grill), and then simultaneously ignite the burner. Hold the button down for a few seconds to stabilize the flame.

Flame control: With propane, the inner dart of the flame should be blue with a sharp outline. This aspect ensures correct combustion and optimal operation of the device.

Gas safety: In case of a gas smell, open the windows, immediately evacuate the area, and close the bottle valve without operating any electrical switches or opening any open flames. To check for leaks, use an approved electronic detector or a non-corrosive product (never use soapy solution or open flame).

Question 4

How to properly install the Smev FO300L oven?

Accepted Answer

To properly install your Smev FO300L oven, follow the steps below to ensure safe and durable operation. This built-in gas oven for camper vans and caravans requires specific preparation of the location and connections.

Preparation of the location: The cabinet must be built square, with a horizontal work surface and a plumb front. The built-in opening must also be perfectly square. Depending on your model, refer to figure 1 in the manual to observe the minimum distances to be maintained between the walls, the floor, and the oven. If the cabinet has ventilation openings, ensure that no combustible material can access them. Drill a hole in the cabinet according to figure 2, depending on your model.

Gas connection: Use a rigid metal pipe with sealed fittings. If you use a flexible pipe (maximum 1.5 m), it must be accessible for inspection, protected from hot parts and stresses (twisting, pulling, crushing), away from moving elements like drawers, and replaced before the expiration date. Once the connection is made, check the tightness of the circuit with a non-corrosive fluid (never use soapy solution) - do not use open flames for this verification. Your Smev FO300L oven operates with butane G30 or propane G31 at a pressure of 30 mbar.

Electrical connection: This is a critical element for this model. The oven can only be connected to a 12 V DC generator (caution: never connect to 230 V, this will cause permanent destruction of the device). The circuit must be protected by a fuse of a maximum of 3 amperes. Use a double red and black cable of 1.5 mm² and connect it to the terminal box located at the back of the device: red terminal for the positive pole, black terminal for the negative pole. Strictly observe the polarities.

Securing the oven: Once installed, secure the oven to the cabinet using the screws provided in the installation kit (see figure 5 in the manual). The oven must be firmly immobilized to avoid any risk of tipping.

Ventilation and first ignition: The use of gas produces heat and humidity. Keep the natural ventilation openings open or install appropriate mechanical ventilation. Before cooking food for the first time, run the oven at maximum intensity for at least 30 minutes, and the grill for 15 to 20 minutes. After each use, close the main valve of the gas pipe.

The thermostat of the FO300L offers 6 temperature settings: 130°C, 160°C, 180°C, 200°C, 220°C, and 240°C. Follow all safety instructions mentioned in the complete manual, especially regarding accessible hot parts and monitoring children. If you detect a gas smell, immediately open the windows, evacuate people, do not use flames or electrical devices, and contact an authorized technician.

User manual Smev Oven : user manuals and guides in PDF

Models Smev Oven most viewed

Other categories Smev

Recent questions about Oven Smev