Q: What does the error code CN008 mean on the Robolinho 520 W?

CN008 means "Loop signal too weak" . This error code indicates that the signal from the peripheral cable is too weak for the mower to correctly detect the boundaries of the cutting area. Main causes The peripheral cable is buried too deeply underground Insufficient signal from the boundary wire Recommended solutions Check the status of the LEDs on the base station Check the power supply to the base station Unplug and replug the power adapter Raise the peripheral cable to the prescribed height If necessary, secure the cable directly on the grass instead of burying it

Q: How to raise the blades of the SOLO Robolinho 700 W lawn mower?

To raise the blades of your Robolinho 700 W , you need to access the cutting height adjustment. The robot has a manual adjustment system with a rotary knob located on the top of the device. The cutting height can be gradually adjusted from 25 to 55 mm according to your needs. Adjustment procedure: Open the cover : Lift the cover of the robot to access the adjustment knob. The cover is usually held by clips or hinges that are easy to manipulate. Locate the rotary knob : You will see a rotary knob dedicated to height adjustment, accompanied by an inspection window that displays the current height in millimeters. Check this window to verify the current setting and the desired setting. Increase the cutting height : To raise the blades (increase the lawn height), turn the knob clockwise . Continue turning until you reach the desired height displayed in the inspection window. Check the setting : Consult the inspection window to confirm that you have reached the desired height. A height of 55 mm is recommended during the first use for the robot's automatic calibration run. Close the cover : Carefully fold down the cover. The device is now ready to mow with the blades at the desired height. You can change the cutting height at any time before starting the robot. To lower the cutting height (if you want a closer cut), proceed in the same way but by turning the knob counterclockwise .

Question 1

What does the error code CN008 mean on the Robolinho 520 W?

Accepted Answer

CN008 means "Loop signal too weak". This error code indicates that the signal from the peripheral cable is too weak for the mower to correctly detect the boundaries of the cutting area.

Main causes

The peripheral cable is buried too deeply underground
Insufficient signal from the boundary wire

Recommended solutions

Check the status of the LEDs on the base station
Check the power supply to the base station
Unplug and replug the power adapter
Raise the peripheral cable to the prescribed height
If necessary, secure the cable directly on the grass instead of burying it

Question 2

How to raise the blades of the SOLO Robolinho 700 W lawn mower?

Accepted Answer

To raise the blades of your Robolinho 700 W, you need to access the cutting height adjustment. The robot has a manual adjustment system with a rotary knob located on the top of the device. The cutting height can be gradually adjusted from 25 to 55 mm according to your needs.

Adjustment procedure:

Open the cover: Lift the cover of the robot to access the adjustment knob. The cover is usually held by clips or hinges that are easy to manipulate.
Locate the rotary knob: You will see a rotary knob dedicated to height adjustment, accompanied by an inspection window that displays the current height in millimeters. Check this window to verify the current setting and the desired setting.
Increase the cutting height: To raise the blades (increase the lawn height), turn the knob clockwise. Continue turning until you reach the desired height displayed in the inspection window.
Check the setting: Consult the inspection window to confirm that you have reached the desired height. A height of 55 mm is recommended during the first use for the robot's automatic calibration run.
Close the cover: Carefully fold down the cover. The device is now ready to mow with the blades at the desired height.

You can change the cutting height at any time before starting the robot. To lower the cutting height (if you want a closer cut), proceed in the same way but by turning the knob counterclockwise.

User manual SOLO Robot mower : user manuals and guides in PDF

Models SOLO Robot mower most viewed

Other categories SOLO

Recent questions about Robot mower SOLO