H1081 - Video projector VIVITEK - Free user manual and instructions

Product Type	Video Projector
Brand	Vivitek
Model	H1081
Display Technology	DLP
Native Resolution	1920 x 1080 (Full HD)
Brightness	2000 ANSI Lumens
Contrast Ratio	3000:1 (typical)
Lamp Life (Normal Mode)	3000 hours
Lamp Life (Eco Mode)	4000 hours
Projection Distance (from screen)	1.2 - 10 meters
Image Size (diagonal)	25.6 - 308 inches
Keystone Correction	Vertical ±30°
Input Connectors	HDMI, VGA, Composite, S-Video, USB
Dimensions (W x D x H)	335 x 256 x 102 mm
Weight	3.6 kg
Power Consumption (Normal)	290W
Power Consumption (Standby)	Less than 1W
Noise Level (Normal Mode)	33 dB
Noise Level (Eco Mode)	28 dB
Bundled Accessories	Remote control, power cord, VGA cable, user manual
Maintenance	Clean air filter every 100 hours; lamp replacement after 3000-4000 hours
Safety Features	Auto shut-off, overheat protection, Kensington lock slot
Spare Parts / Repairability	Lamp module, air filter, remote control available; serviceable by authorized technicians

Frequently Asked Questions - H1081 VIVITEK

How do I connect my laptop to the Vivitek H1081 projector?

Use a VGA or HDMI cable. Connect one end to your laptop and the other to the corresponding port on the projector. Then select the correct input source using the Source button on the remote or projector.

What is the recommended projection distance for a 100-inch screen?

For a 100-inch diagonal image, the projector should be placed approximately 3.5 to 4.5 meters from the screen, depending on zoom settings.

How can I replace the lamp in my H1081 projector?

Turn off and unplug the projector. Allow it to cool. Open the lamp cover on the bottom, loosen the lamp screws, remove the old lamp, and insert the new one. Tighten screws and close the cover. Reset the lamp timer in the Settings menu.

Why is my projector displaying a 'Lamp' warning message?

This indicates the lamp is nearing the end of its life. Replace the lamp as soon as possible. The warning typically appears when the lamp has been used for approximately 2900 hours in normal mode.

Can I use the projector without a screan?

Yes, you can project onto any flat, white or light-colored wall, but a proper projection screen will provide better brightness and contrast.

How do I clean the air filter?

Turn off and unplug the projector. Remove the air filter cover, take out the filter, and gently vacuum or wash with mild soap. Dry completely before reinstalling. Clean every 100 hours of use.

Does the H1081 support 3D content?

The H1081 is primarily a 2D projector. It does not support 3D playback natively. Check the manual for possible compatibility with external 3D converters.

What is the meaning of the blinking LED indicators?

A steady green LED means power on. Blinking green indicates standby. A red blinking LED signals a malfunction (e.g., overheating, lamp error). Refer to the troubleshooting section of the manual for specific codes.

Can I mount the projector on the ceiling?

Yes, the H1081 supports ceiling mounting. Use a compatible mount and invert the image using the Projection Mode setting to 'Ceiling Mount Reverse'.

How do I adjust the image keystone?

Press the Keystone button on the remote. Use the arrow keys to correct vertical distortion. For best results, position the projector perpendicular to the screen.

USER MANUAL H1081 VIVITEK

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

© Copyright 2009

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.

All other product names used in this manual are the properties of their respective owners and are acknowledged.

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.

The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example:

"Push the MENU button on the remote control to open the DISPLAY menu."

General Safety Information

Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact qualified service personnel.
➢ Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
- Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.

Projector Installation Notice

➢ Place the projector in a horizontal position

The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.

- Allow at least 50 cm clearance around the exhaust vent.

➢ Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable 5 – 35°C range.

Power Safety

▶ Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 30 for clear and safe instructions for this procedure. Before replacing the lamp:

▶ Unplug the power cord.
- Allow the lamp to cool for about one hour.

Cleaning the Projector

➢ Unplug the power cord before cleaning. See Cleaning the Projector on page 32.
- Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section on page 44.

Important Recycle Instructions:

Hg

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.

Main Features

• Lightweight unit, easy to pack away and transport.
• Compatible with all major video standards including NTSC, PAL, and SECAM.
• A high brightness rating allows for presentations in daylight or in lit rooms.
  • Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images.
• Flexible setup allows for front, rear projections.
• Line-of-vision projections remain square, with advanced keystone correction for angled projections.
• Input source automatically detected.

About this manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

Table of Contents

GETTING STARTED....1

PACKING CHECKLIST .... 1

VIEWS OF PROJECTOR PARTS....2

H1080 Series Front-right View....2

Top view—On-screen Display (OSD) buttons and LEDs 3

Rear view 4

Bottom view....5

REMOTE CONTROL PARTS 6

REMOTE CONTROL OPERATING RANGE....8

PROJECTOR AND REMOTE CONTROL BUTTONS 8

SETUP AND OPERATION....9

INSERTING THE REMOTE CONTROL BATTERIES 9

CONNECTING INPUT DEVICES....10

STARTING AND SHUTTING DOWN THE PROJECTOR....11

ADJUSTING THE ZOOM RING, FOCUS AND KEYSTONE....14

ADJUSTING THE VOLUME 15

ON-SCREEN DISPLAY (OSD) MENU SETTINGS....16

OSD MENU CONTROLS 16

Navigating the OSD 16

SETTING THE OSD LANGUAGE 17

OSD MENU OVERVIEW 18

PICTURE>>BASIC MENU....19

BILLEDE>>AVANCERERT MENU 20

HSG Adjustment....21

DISPLAY MENU 22

PC Detail Adjustment....23

SETUP>>BASIC MENU 24

Menu Settings....25

Source 25

SETUP>>ADVANCED MENU 26

Audio....27

Lamp 27

HDMI 28

Closed Caption 28

STATUS MENU 29

MAINTENANCE AND SECURITY....30

REPLACING THE PROJECTION LAMP....30

CLEANING THE PROJECTOR....32

Cleaning the Lens 32

Cleaning the Case....32

USING THE KENSINGTON ^® LOCK 33

TROUBLESHOOTING 34

COMMON PROBLEMS AND SOLUTIONS 34

TIPS FOR TROUBLESHOOTING 34

LED ERROR MESSAGES....35

IMAGE PROBLEMS....35

LAMP PROBLEMS 36

REMOTE CONTROL PROBLEMS 36

AUDIO PROBLEMS 37

HAVING THE PROJECTOR SERVICED 37

SPECIFICATIONS....39

SPECIFICATIONS....39

PROJECTION DISTANCE VS. PROJECTION SIZE....40

H1080 Series Projection Distance and Size Table.... 40

H1080 SERIES TIMING MODE TABLE....41

PROJECTOR DIMENSIONS 43

REGULATORY COMPLIANCE 44

FCC WARNING......44

CANADA 44

SAFETY CERTIFICATIONS....44

GETTING STARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

Line drawing of a VR projector with visible brand logo and front panel (no text or symbols on body)

H1080 SERIES DLP PROJECTOR

White remote control with keypad and two separate electrical clamps (no text or symbols visible)

REMOTE CONTROL (WITH TWOAA BATTERIES)

Line drawing of a USB cable with two connectors (no text or symbols)

HDMI CABLE

Line drawing of a multi-wire electrical cable with multiple connectors (no text or symbols)

COMPONENT CABLE

Coiled cable or wire with connectors, no visible text or symbols

POWER CORD

QUICK START CARD

WARRANTY CARD

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service.

Caution:

Avoid using the projector in dusty environments.

Views of Projector Parts

H1080 Series Front-right View

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	Height-adjuster button Push to release height adjuster		13
2.	Height adjuster Adjusts level of projector
3.	Lens	Projection Lens
4.	IR receiver Receive IR signal from remote control		6
5.	Focus ring Focuses the projected image		14
6.	Zoom ring Enlarges the projected image
7.	Function keys	See Top view—On-screen Display (OSD) buttons and LEDs.	3

Important:

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.

Top view—On-screen Display (OSD) buttons and LEDs

graph TD
    A["1"] --> B["Power Control"]
    B --> C["ENTER"]
    C --> D["MENU"]
    C --> E["SOURCE"]
    D --> F["AUTO"]
    E --> F
    F --> G["7"]
    F --> H["8"]
    F --> I["9"]
    F --> J["10"]
    F --> K["11"]
    F --> L["12"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#cff,stroke:#333
    style F fill:#ffc,stroke:#333
    style G fill:#fff,stroke:#333
    style H fill:#fff,stroke:#333
    style I fill:#fff,stroke:#333
    style J fill:#fff,stroke:#333
    style K fill:#fff,stroke:#333
    style L fill:#fff,stroke:#333

ITEM LABEL DESCRIPTION				SEE PAGE:
1.	(Power button)	Turns the projector On or Off.		11
2.	BLANK Displays a blank	screen and mutes audio
3.	(Left cursor)/Volume-	Navigates and changes settings in the OSD Quick Menu – For Volume		16
4.	Enter Enter or confirm highlighted OSD menu item
5.	MENU Opens and exits OSD menus
6.	(Up cursor)/Keystone+	Navigates and changes settings in the OSD Quick Menu – For Keystone
7.	AUTO Optimizes image size, position, and resolution
8.	(Right cursor)/Volumc+	Navigates and changes settings in the OSD Quick Menu – For Volume		16
9.	SOURCE Enter the Source menu			10
10.	(Down cursor)/Keystone-	Navigates and changes settings in the OSD Quick Menu – For Keystone		16
11.	READY LED	Red Lamp is ready to be powered-on.
		Flashing	Lamp is not ready (warming up/shutting down/cooling) (see LED Error Messages on page 35)
12.	TEMP LED Flashing Error code

Rear view

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	AC IN Connect the POWER CABLE		11
2.	(USB)	Connect the USB CABLE from a computer	10
3.	COMPONENT IN Connect a component video enabled device
4.	S-VIDEO IN Connect the S-VIDEO CABLE from a video device
5.	VIDEO IN Connect the COMPOSITE CABLE from a video device
6.	VGA IN Connect the RGB CABLE from a computer.
7.	HDMI - 1 Connect the HDMI CABLE from a HDMI device
8.	HDMI - 2 Connect the HDMI CABLE from a HDMI device
9.	DC 12V Connect the 12V OUT
10.	Kensington Lock	Secure to permanent object with a Kensington® Lock system	33
11.	Speaker	Outputs audio sound	10
12.	IR receiver Receive IR signal from remote control		6
13.	AUDIO IN (L and R) Connect the AUDIO CABLES from a audio device		10
14.	AUDIO IN Connect an AUDIO CABLE from the input device
15.	RS-232C	Connect RS-232 serial port cable for remote control
16.	AUDIO OUT	Connect an AUDIO CABLE for audio loop through

Note: If your video equipment has various input sources, it is recommended to connect in priority of HDMI, component, S-Video, Composite for better picture quality.

Bottom view

ITEM	LABEL	DESCRIPTION	SEE PAGE:
	Tilt adjustor Rotate adjuster lever to adjust angle position.		131.
2.	Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling
3.	Height adjustor Adjuster drops down when adjuster button is pushed.		13
4.	Height adjustor button Push to release adjustor.

Note:

When installing, ensure that you use only UL Listed ceiling mounts.

For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm (0.23 inch).

The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a period of 60 seconds.

Remote Control Parts

graph TD
    A["31"] --> B["POWER"]
    C["30"] --> D["ON"]
    E["29"] --> F["HDMI1"]
    G["28"] --> H["COMP"]
    I["27"] --> J["PC"]
    K["26"] --> L["ENTER"]
    M["25"] --> N["EXIT MENU"]
    O["24"] --> P["PICTURE MODE"]
    Q["23"] --> R["CONTRAST"]
    S["22"] --> T["MUTE"]
    U["21"] --> V["VOL +"]
    W["20"] --> X["VOL -"]
    Y["1"] --> Z["OFF"]
    AA["2"] --> AB["SOURCE"]
    AC["3"] --> AD["HDMI2"]
    AE["4"] --> AF["S-VIDEO"]
    AG["5"] --> AH["VIDEO"]
    AI["6"] --> AJ["ENTER"]
    AK["7"] --> AL["EXIT"]
    AM["8"] --> AN["ASPECT RATIO"]
    AO["9"] --> AP["OPTION"]
    AQ["10"] --> AR["SOURCE STATUS"]
    AS["11"] --> AT["BRIGHT SHARP"]
    AU["12"] --> AV["COLOR TINT"]
    AW["13"] --> AX["FREEZE BLANK"]
    AY["14"] --> AZ["TINT AUTO"]
    BA["15"] --> BB["AUTO"]
    BC["16"] --> BD["FREEZE BLANK"]
    BE["17"] --> BF["BRIGHT SHARP"]
    BG["18"] --> BH["COLOR TINT"]
    BI["19"] --> BJ["FREEZE BLANK"]

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user's manual describes the functions based on the remote control.

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	Power OFF Turns the projector off		11
2.	HDMI 2 Displays the HDMI 2 source selection
3.	S-VIDEO Displays the S-VIDEO source selection
4.	VIDEO Displays the VIDEO source selection
5.	Up cursor / Keystone+	Navigates and changes settings in the OSD Quick Menu - For Keystone	16
6.	ENTER Enters and confirms settings in the OSD
7.	Right cursor	Navigates and changes settings in the OSD
8.	Down cursor
9.	ASPECT RATIO Displays the ASPECT RATIO selections
10.	SOURCE Detects the input device
11.	STATUS	Opens the OSD Status menu (the menu only opens when an input device is detected)	16
12.	BRIGHT Displays the brightness setting bar
13.	SHARP Displays the sharpness setting bar
14.	COLOR Displays the color setting bar
15.	TINT Displays the tint setting bar
16.	BLANK Makes the screen blank
17.	FREEZE	Freezes/unfreezes the on-screen picture
18.	AUTO	Auto adjustment for frequency, phase, and position
19.	LIGHT	Turns on or off the remote control backlight for about 10 seconds. Pressing any other key while the backlight is on keeps the backlight on for a further 10 seconds.
20.	VOL -	Adjusts volume	16
21.	VOL +
22.	MUTE Mutes the built-in speaker
23.	CONTRAST	Displays the contrast settings bar
24.	PICTURE MODE	Changes the Display Mode setting
25.	MENU/ EXIT	Opens and exits the OSD	16
26.	Left cursor	Navigates and changes settings in the OSD
27.	COMP	Displays the Component source selection
28.	PC	Displays the PC source selection
29.	HDMI 1 Displays the HDMI 1 source selection
30.	Power ON	Turns the projector on	11
31.	IR transmitter	Transmits signals to projector

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are limited in use.

SETUP AND OPERATION

Inserting the Remote Control Batteries

1. Remove the battery compartment cover by sliding the cover in the direction of the arrow.

Diagram of a mechanical component with an arrow indicating direction (no text or symbols present)

1. Insert the battery with the positive side facing up.

Diagram of a remote control device showing battery casing and battery with arrows indicating rotation (no text or symbols)

1. Replace the cover.

Diagram of a vehicle door frame with an arrow indicating direction (no text or symbols)

Caution:

1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.

Connecting Input Devices

A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.

ITEM LABEL DESCRIPTION
	(USB)	Connect the USB cable from a computer
	COMPONENT IN Connect the S-VIDEO IN Connect the S-VIDEO cable from a video device
	VIDEO IN Connect the COMPOSITE cable from a video device
	VGA IN Connect the RGB cable from a computer.
	HDMI - 1	Connect the HDMI cable from a HDMI device
	HDMI - 2
	DC 12V Connect the 12V OUT
	AUDIO IN (L and R) Connect the AUDIO cables from a audio device
	AUDIO IN Connect an AUDIO cable from the input device
	RS-232C Connect RS-232 serial port cable for remote control
	AUDIO OUT Connect an AUDIO cable for audio loop through

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

Starting and Shutting down the Projector

1. Connect the power cord to the projector. Connect the other end to a wall outlet. The ⏻ POWER LED will be on.
2. Turn on the connected devices.
3. Ensure the ⏻ POWER LED displays a solid blue and not a flashing blue. Then press the ⏻ POWER button to turn on the projector.

The projector splash screen displays and connected devices are detected.

Pure electrical outlet diagram without any text, numbers, or symbols

1. If more than one input device is connected, press the SOURCE button and use ▲▼ to scroll among devices.

• PC: Analog RGB
• HDMI 1/2: High Definition Multimedia Interface
• Component: DVD input YCbCr / YPbPr.
• S-Video: Super video (Y/C separated)
• Video: Traditional composite video

1. When the POWER OFF window appears, press ⏻ on the control panel or OFF on the remote control. The projector turns off.

Caution:

Do not unplug the power cord until the READY LED stops flashing-indicating the projector has cooled down.

Adjusting the Projector Level

Take note of the following when setting up the projector:

• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle.
• Ensure the cables are in a safe location. You could trip over them.

1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B].
   The height adjuster drops down [C].
2. To lower the level of the projector, press the height-adjuster button and push down on the top of the projector.
3. To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the desired angle has been achieved.

Adjusting the Zoom ring, Focus and Keystone

1. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B.
2. Use the Image-focus control (on the projector only) to sharpen the projected image Ⓐ.
3. Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.

graph TD
    A["POWER"] --> B["ON"]
    A --> C["OFF"]
    B --> D["SOURCE"]
    D --> E["HDMI1"]
    D --> F["HDMI2"]
    D --> G["S-VIDEO"]
    D --> H["COMP"]
    D --> I["PC"]
    D --> J["VIDEO"]
    K["ENTER"] --> L["EXIT MENU"]
    K --> M["EXIT MENU WITH AUTO"]
    K --> N["FEATURE MODE SOURCE STATUS"]
    K --> O["CONTANT BRIGHT SHARP"]
    K --> P["MUTE COLOR TINT"]
    Q["MENU"] --> R["AUTO"]
    R --> S["ENTER"]
    S --> T["BLANK"]
    S --> U["SOURCE"]
    V["Power"] --> W["OFF"]
    X["EXIT MENU"] --> Y["EXIT MENU WITH AUTO"]

Remote control and OSD panel

1. The keystone control appears on the display.

Adjusting the Volume

1. Press the Volume +/- buttons on the remote control. The volume control appears on the display.

graph TD
    A["ENTER"] --> B["MENU"]
    A --> C["SOURCE"]
    A --> D["AUTO"]
    A --> E["Blank"]
    A --> F["Source"]
    G["EXIT MENU"] --> H["AFFECT RATIO"]
    I["PICTURE MODE"] --> J["SOURCE STATUS"]
    K["CONTRAST"] --> L["BRIGHT SHARP"]
    M["MUTE"] --> N["COLOR TINT"]
    O["VOL ← FREEZE BLANK"] --> P["VOL ← LIGHT AUTO"]
    Q["VOL ← Light AUTO"] --> R["Power Button"]

1. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-

1. Press the MUTE button to turn off the volume (This feature is available only on the remote).

ON-SCREEN DISPLAY (OSD) MENU SETTINGS

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector.

graph TD
    A["ENTER"] --> B["MENU"]
    A --> C["AUTO"]
    A --> D["SOURCE"]
    A --> E["BLANK"]
    A --> F["1"]
    A --> G["1"]
    A --> H["2"]
    A --> I["3"]
    A --> J["4"]
    A --> K["5"]
    A --> L["6"]
    A --> M["7"]

1. To enter the OSD, press the MENU button.
2. There are six menus. Press the cursor ◀▶ button to move through the menus.
3. Press the cursor ▲▼ button to move up and down in a menu.
4. Press ◀▶ to change values for settings.
5. Press MENU to close the OSD or leave a sub menu.

Note:

Depending on the video source, not all items in the OSD are available. For example, the PC Detail Adjustment item in the PICTURE>>Basic menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.

Setting the OSD Language

Set the OSD language to your preference before continuing.

1. Press the MENU button. Press the cursor ◀▶ button to navigate to SETUP>>Basic.

1. Press the cursor ▲▼ button until Language is highlighted.
2. Press the cursor ◀▶ button until the language you want is selected.
3. Press the MENU button to close the OSD.

OSD Menu Overview

Use the following illustration to quickly find a setting or determine the range for a setting.

graph TD
    A["PICTURE>> Basic"] --> B["Display Mode"]
    A --> C["User Mode"]
    A --> D["Brightness"]
    A --> E["Contrast"]
    A --> F["Color"]
    A --> G["Tint"]
    A --> H["Sharpness"]
    A --> I["Flesh Tone"]
    A --> J["Save Setting"]
    A --> K["Reset Picture Setting"]

    B --> L["Movie/Bright/Normal/User 1/User 2/User 3/ISF Day/ISF Night"]
    C --> M["Movie/Bright/Normal"]

    D --> N["Contrast"]
    E --> O["Color"]
    F --> P["Tint"]
    G --> Q["Sharpness"]
    H --> R["Flesh Tone"]
    I --> S["Save Setting"]
    J --> T["Reset Picture Setting"]

    L --> U["Enter"]
    M --> V["Primary Color"]
    N --> W["Auto/RGB/STDV/HDTV"]

    U --> X["Setting Saved"]
    V --> Y["Enter"]
    W --> Z["Yes/No"]

    AA["PICTURE>> Advanced"] --> AB["Noise Reduction"]
    AA --> AC["Color Temperature"]
    AA --> AD["Gamma"]
    AA --> AE["HSG Adjustment"]
    AA --> AF["Color Space"]

    AB --> AG["Lamp Native/Warm/Normal/Cool/Cooler/High Cool"]
    AC --> AH["Primary Color"]
    AD --> AI["Auto/RGB/STDV/HDTV"]

    AE --> AJ["Auto/Frequency/Phase/Horizontal Position/Vertical Position"]
    AF --> AK["On /Off"]

    AL["DISPLAY"] --> AM["Aspect Ratio"]
    AL --> AN["Keystone"]
    AL --> AO["Overscan"]
    AL --> AP["PC Detail Adjustment"]
    AL --> AQ["Auto Keystone"]

    AM --> AR["Auto/16:9/4:3/Letter Box/Real"]
    AN --> AS["Overscan"]
    AP --> AT["Auto/Frequency/Phase/Horizontal Position/Vertical Position"]
    AQ --> AU["On /Off"]

    AV["SETUP>> Basic"] --> AW["Language"]
    AV --> AX["Splash Logo"]
    AV --> AY["Projection"]
    AV --> AZ["Blank Timer"]
    AV --> BA["Auto Power Off"]
    AV --> BB["Sleep Timer"]
    AV --> BC["Background Color"]
    AV --> BD["Menu Settings"]
    AV --> BE["Source"]

    AW --> BF["English/ Danish/ Dutch/ Finnish/ French/ German/ Italian/ Japanese/ Korea/ Norwegian/ Polish/ Portuguese/ Russian/ Traditional Chinese/ Simplified Chinese/ Spanish/ Swedish"]
    AX --> BG["VIVITEK/Blue/Black"]

    AX --> BH["Front Table/Front Ceiling/Rear Table/Rear Ceiling"]
    AX --> BI["Disable / 5 Min / 10 Min / 15 Min / 20 Min / 25 Min / 30 Min"]
    AX --> BJ["Disable / 5 Min / 10 Min / 15 Min / 20 Min / 25 Min / 30 Min"]
    AX --> BK["Disable / 30 Min / 1 Hr / 2 Hr / 3 Hr / 4 Hr / 8 Hr / 12 Hr"]

    BA --> BL["Purple/Black/Black"]
    BA --> BM["Menu position"]
    BA --> BN["Menu Display Time"]

    BL --> BO["Top-Left/Top-Right/Center/Dutton-Left/Dockout/Right"]
    BL --> BP["5 Sec / 10 Sec / 15 Sec / 20 Sec / 25 Sec / 30 Sec"]

    BS["SETUP>> Advanced"] --> BT["Audio"]
    BS --> BU["Volume"]

    BT --> BV["Treble"]
    BT --> BW["Bass"]

    BT --> BX["Mule"]
    BT --> BY["AGC"]
    BT --> BZ["Reset"]

    BT --> CA["Component"]
    BT --> CB["Video"]
    BT --> CC["S-Video"]
    BT --> CD["Quick Auto Search"]

    BC["Audio"] --> BD
    BC --> BE
    BC --> BF

    BD --> BG["Check/uncheck"]

    BE --> BH
    BE --> BI["Check/uncheck"]

    BC --> BJ
    BC --> BK

    BC --> BL
    BC --> BN

    BC --> CA

    BC --> BD

PICTURE>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◀▶ to change values for settings.

Note:

Customizing the settings in PICTURE>>Basic menu is only available in User 1/2/3 mode.

ITEM DESCRIPTION
Display Mode	Press the cursor ◀▶ buttons to set the Display Mode.(Range: Movie/ Bright/ Normal/ User 1/ User 2/ User 3)Notes: ISF Day/ISF Night is available when ISF Mode is on.
User Mode	Press the cursor ◀▶ buttons to set the User Mode.(Range: Movie/ Bright / Normal)
Brightness	Press the cursor ◀▶ buttons to adjust the display brightness.
Contrast	Press the cursor ◀▶ buttons to adjust the display contrast.
Color	Press the cursor ◀▶ buttons to adjust the video saturation.Notes: This function is only available when Component, Video or S-Video input source is selected.
Tint	Press the cursor ◀▶ buttons to adjust the video tint/hue.Notes: This function is only available when Component, Video or S-Video with NTSC system input source is selected.
Sharpness	Press the cursor ◀▶ buttons to adjust the display sharpness.Notes: This function is only available when Component, Video or S-Video input source is selected.
Flesh Tone	Press the cursor ◀▶ buttons to adjust the display flesh tone.Notes: This function is only available when Component, Video or S-Video input source is selected.
Save Setting	Press the ENTER button to save all settings.
Reset Picture Settings	Press the ENTER button to reset all settings to default values.

PICTURE>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◀▶ to change values for settings.

ITEM DESCRIPTION
Noise Reduction	Press the cursor ◀▶ button to adjust the Noise Reduction.
Color Temperature	Press the cursor ◀▶ button to set the Color Temperature.
Gamma	Press the cursor ◀▶ button to adjust the gamma correction of the display.Notes: This function is only available in User 1/2/3 mode.
HSG Adjustment	Press the ENTER button to enter the HSG Adjustment sub menu.See HSG Adjustment on page 21.
Color Space	Press the cursor ◀▶ button to set the Color Space.(Range: Auto/ RGB/ SDTV/ HDTV)Notes: This function is only available when HDMI input source is selected.

HSG Adjustment

Press the ENTER button to enter the HSG Adjustment sub menu.

ITEM DESCRIPTION
Primary Color	Press the ◀▶ buttons to set the Primary Color.Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized.
Huc	Press the ◀▶ buttons to adjust the Huc.
Saturation	Press the ◀▶ buttons to adjust the Saturation.
Gain	Press the ◀▶ buttons to adjust the Gain.

DISPLAY Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◀▶ to change values for settings.

ITEM DESCRIPTION
Aspect Ratio	Press the cursor ◀▶ button to set the Aspect Ratio.(Range: Auto/ 16:9/ 4:3/ Letter Box/ Real)
Keystone	Press the cursor ◀▶ button to adjust the Keystone.Notes: This function is available when the Auto keystone function is turned off.
Overscan	Press the cursor ◀▶ button to adjust the Overscan.
PC Detail Adjustment	Press the ENTER button to enter the PC Detail Adjustment sub menu.See PC Detail Adjustment on page 23.
Auto Keystone	Press the cursor ◀▶ button to turn on or off the Auto Keystone.Notes: When Auto Keystone is on, the projector will automatically adjust the Keystone.

PC Detail Adjustment

Press the ENTER button to enter the PC Detail Adjustment sub menu.

Note:

Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.

ITEM DESCRIPTION
Auto	Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the remote control to automatically adjust frequency, phase, and position.
Frequency	Press the ◀▶ buttons to adjust the A/D sampling number.
Phase	Press the ◀▶ buttons to adjust the A/D sampling clock.
Horizontal Position	Press the ◀▶ buttons to adjust the display position right or left.
Vertical Position	Press the ◀▶ buttons to adjust the display position up or down.

SETUP>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◀▶ to change values for settings.

ITEM DESCRIPTION
Language	Press the cursor ◀▶ buttons to select a different localization menu.(Range: English/ Danish/ Dutch/ Finnish/ French/ German/ Italian/ Japanese/ Korea/Norwegian/ Polish/ Portuguese/ Russian/ Traditional Chinese/ Simplified Chinese/ Spanish/ Swedish)
Splash Logo	Press the cursor ◀▶ buttons to select a different startup screen.(Range: Vivitek/ Blue/ Black)
Projection	Press the cursor ◀▶ buttons to choose from four projection methods:Front Table/ Front Ceiling/ Rear Table/ Rear Ceiling.
Blank Timer	Press the cursor ◀▶ buttons to set the Blank Screen timer. The projected image is automatically restored after the set time.(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Auto Power Off	Press the cursor ◀▶ buttons to set the Auto Power Off timer. The projector automatically turns off if no input source is detected after the preset period of time.(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Sleep Timer	Press the cursor ◀▶ buttons to set Sleep timer. The projector automatically turns off after the preset period of time.(Range: Disable/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr)
Background Color	Press the cursor ◀▶ buttons to select the background color when no input source is detected.(Range: Purple/ Black/ Blue)
Menu Settings	Press the ENTER button to enter the Menu Settings sub menu. See Menu Settings on page 25.
Source	Press the ENTER button to enter the Source sub menu. See Source on page 25.

Menu Settings

Press the ENTER button to enter the Menu Settings sub menu.

Menu Settings
Menu Position	Center
Menu Display Time	5 Sec

ITEM DESCRIPTION
Menu Position	Press the ◀▶ buttons to select from five OSD locations:Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right.
Menu Display Time	Press the ◀▶ buttons to set the Menu Display timer before the OSD times out.(Range: 5sec/ 10sec/ 15sec/ 20sec/ 25sec/ 30sec)

Source

Press the ENTER button to enter the Source sub menu.

Source
PC	√
HDMI 1	√
HDMI 2	√
Component	√
Video	√
S-Video	√
Quick Auto Search	Off

ITEM DESCRIPTION
PC	Press the ◀▶ buttons to enable or disable the PC source.
HDMI 1	Press the ◀▶ buttons to enable or disable the HDMI source.
HDMI 2
Component	Press the ◀▶ buttons to enable or disable the Component source.
Video	Press the ◀▶ buttons to enable or disable the Video source.
S-Video	Press the ◀▶ buttons to enable or disable the S-Video source.
Quick Auto Search	Press the ◀▶ buttons to enable or disable Quick Auto Search for available input source.Notes:When the desired source is selected, the Quick Auto Search function will be turn off.

SETUP>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu.

ITEM DESCRIPTION
Audio	Press the ENTER button to enter the Audio sub menu. See Audio on page 27.
Lamp	Press the ENTER button to enter the Lamp sub menu. See Lamp on page 27.
HDMI	Press the ENTER button to enter the HDMI sub menu. See HDMI on page 28.
High Altitude Mode	Press the cursor ◀▶ buttons to turn on or off High Altitude Mode when the altitude of the environment is higher than 1500m, or the temperature is over 40°C.
Test Pattern	Press the cursor ◀▶ buttons to turn on or off the grid test pattern.
Closed Caption	Press the ENTER button to enter the Closed Caption sub menu.See Closed Caption on page 28.
LED Control	Press the cursor ◀▶ buttons to select the LED control.Select Normal for normal LED display and Off to disable LED display.
Reset All	Press the ENTER button to enter reset all settings to default values.

Audio

Press the ENTER button to enter the Audio sub menu.

ITEM DESCRIPTION
Volume	Press the ◀▶ buttons to adjust the audio Volume.
Bass	Press the ◀▶ buttons to adjust the audio Bass.
Treble	Press the ◀▶ buttons to adjust the audio Treble.
Mute	Press the ◀▶ buttons to turn on or off the speaker.
AGC	Press the ◀▶ buttons to turn on or off the AGC setting.
Reset	Press the ENTER button to reset all settings to default values.

Lamp

Press the ENTER button to enter the Lamp sub menu.

ITEM DESCRIPTION
Lamp Mode	Press the ◀▶ buttons to adjust lamp brightness.
Reset Lamp Timer	Press the ENTER button to reset the Lamp Hour after the lamp is replaced.
Lamp Hour Displays the number of hours the lamp has been in use.

HDMI

Press the ENTER button to enter the HDMI sub menu.

ITEM DESCRIPTION
HDMI Format	Press the ◀▶ buttons to select from three HDMI display formats:Auto/ PC signal/ Video signal.
HDMI Amplifier Gain	Press the ◀▶ buttons to adjust HDMI Amplifier Gain.

Closed Caption

Press the ENTER button to enter the Closed Caption sub menu.

Closed Caption
Closed Caption Enable	On
Caption Version	CC1

ITEM DESCRIPTION
Closed Caption Enable	Press the ◀▶ buttons to turn on or off Closed Caption.
Caption Version	Press the ◀▶ buttons to select the Caption Version.

STATUS Menu

Press the MENU button to open the OSD menu. Press the cursor ◀▶ button to move to the STATUS Menu.

ITEM DESCRIPTION

Source Displays the activated input source.

Resolution Displays the native resolution of input source.

Lamp Hour Displays the number of hours the lamp has been in use.

Firmware Version Displays the firmware version of the projector.

Note: Status displayed in this menu is for viewing only and cannot be edited.

MAINTENANCE AND SECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local authority.

Warning:

Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.

1. Remove the single screw on the lamp compartment cover.

1. Remove the lamp compartment cover.

Diagram of an open projector case with internal components and a lid, showing no text or symbols

1. Remove the three screws from the lamp module.

2. Lift the module handle up.

3. Pull firmly on the module handle to remove the lamp module.

4. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.

Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.

Diagram of an electronic device showing a computer with an open rear panel and a close-up of its internal components (no text or symbols present)

Diagram of an electronic device showing a computer with an open rear panel and a close-up of its internal components (no text or symbols present)

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

Using the Kensington® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

Note:

Contact your vendor for details on purchasing a suitable Kensington security cable.

The security lock corresponds to Kensington's MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: [phone], http://www.Kensington.com.

TROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.

• Use some other electrical device to confirm that the electrical outlet is working.
• Ensure the projector is turned on.
• Ensure all connections are securely attached.
• Ensure the attached device is turned on.
• Ensure a connected PC is not in suspending mode.
• Ensure a connected notebook computer is configured for an external display. (This is usually done by pressing a Fn-key combination on the notebook).

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts.

For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.

LED Error Messages

ERROR CODE MESSAGES	POWER LED BLINK	READY LED BLINK	TEMP LED BLINK
Lamp Ready ON ON OFF
Start	ON
Cooling	ON
Over temperature OFF OFF ON
Thermal Break Sensor error 4 4 OFF
Lamp End of lamp life detected 5 3 OFF
Burner Fan error 6 1 OFF
Lamp Fan error 6 2 OFF
Power Fan error	6 3 OFF
DMD Fan error 6 4 OFF
Case Open	7 OFF OFF
DMD error	8 OFF OFF
Color wheel error	9 OFF OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact your service center.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Installation I menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC's video card, connect to another computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Image menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Re-plug power cord. When the READY LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The information may be useful to service personnel. For servicing, return the projector to the place you purchased it.

HDMI Q & A

Q. What is the difference between a "Standard" HDMI cable and a "High-Speed" HDMI cable?

Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-Speed cables.

- Standard (or "category 1") HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.

- High Speed (or "category 2") HDMI cables have been tested to perform at speeds of 340Mhz or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased color depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).

Q. How do I run HDMI cables longer than 10 meters?

There are many HDMI Adopters working on HDMI solutions that extend a cable's effective distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into cables that boost and extend the cable's signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.

Q. How can I tell if a cable is an HDMI certified cable?

All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test Specification. However, there may be instances where cables bearing the HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively investigates these instances to ensure that the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.

For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49

SPECIFICATIONS

Specifications

Model	H1080 Series
Display type	TI DLP DMD 0.65"
Native Resolution	1920 x 1080
Weight	3.4 kg (7.5 lbs)
Projection distance	1 meters ~ 10 meters
Projection screen size	25" ~ 300"
Projection lens	Manual Focus/Manual Zoom
Zoom ratio	1.2
Vertical keystone correction	+/- 30 degrees
Auto Keystone	Yes
Projection methods	Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility	VGA, SVGA, XGA, SXGA, UXGA, Mac
SDTV/ EDTV/ HDTV	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Video compatibility	NTSC 4.43, PAL (M/N/60), SECAM
H-Sync	15.6 - 91.1 kHz
V-Sync	50 - 85 Hz
Safety certification	FCC-B, UL, cUL, CB, CE, CCC, KC, PCT, and C-tick
Operation temperature	5° ~ 35°C
Dimensions (W x H x D)	332.8 mm x 113 mm x 254.6 mm (13.1" x 4.45" x 10.0")
AC Input	AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/ ± 10%
Power consumption	Standard mode: 250W (Typical)/ 270W (Maximum)Boost mode: 300W (Typical)/ 320W (Maximum)
Stand By	<1 watt
Lamp	230W
Audio speaker	AMP 5W speaker
Input Terminals	Digital: HDMI x 2
	Analog: RGB HD-15 x 1
	Composite: RCA x 1 (Yellow)
	S-Video: mini dim x 1
	Component: RCA x 3
	Audio in: φ3.5 mm stereo mini jack x 1; RCA x 2 R/L
Output Terminals	Mini-jack stereo x 1
	DC_out (screen trigger): DC Jack x 1 (DC12V 200mA output function)
Control Terminals	RS-232: DSUB-9 x 1
	Keyboard Emulation Control: USB connector type B
Security	Kensington lock

Projection Distance vs. Projection Size

H1080 Series Projection Distance and Size Table

16:9 SCREEN				PROJECTION DISTANCE			VERTICAL OFFSET IN CM
DIAGONAL WIDTH HEIGHT				MIN LENGTH (WITH MAX ZOOM)	AVERAGE	MAX LENGTH (WITH MIN ZOOM)
INCH	CM	CM	CM
30	76		66	37		106
40	102		89	50		141	155
50	127		111	62		176	194
60	152		133	75		211	232
80	203		177	100		282	310
100	254		221	125	352		387
120	305		266	149	422		465
150	381		332	187	528		581
200	508		443	249	704		774
220	559		487	274	774		852
250	635		553	311	880		968
300	762		664	374	1056		1162

H1080 Series Timing Mode Table

The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector.

SIGNAL RESOLUTION		H-SYNC (KHz)	V-SYNC (Hz)	COMPOSITE / S-VIDEO	COMPONENT	RGB (ANALOG)	HDMI (DIGITAL)
NTSC	—	15.734		60.0	—	O — —
PAL/SECAM	—	15.625	50.0	O	—	— —
VESA	720 x 400 37	9 85.0 — —	O O
	640 x 480 31	5 60.0 — —	O O
	640 x 480 37	9 72.8 — —	O O
	640 x 480 37	5 75.0 — —	O O
	640 x 480 43	3 85.0 — —	O O
	800 x 600 35	2 56.3 — —	O O
	800 x 600 37	9 60.3 — —	O O
	800 x 600 46	9 75.0 — —	O O
	800 x 600 48	1 72.2 — —	O O
	800 x 600 53	7 85.1 — —	O O
	1024 x 768 48	4 60.0 — —	O O
	1024 x 768 56	5 70.1 — —	O O
	1024 x 768 60	0 75.0 — —	O O
	1024 x 768 68	7 85.0 — —	O O
	1280 x 800 49	7 59.8 — —	O O
	1280 x 800 62	8 74.9 — —	O O
	1280 x 800 71	6 84.8 — —	O O
	1280 x 1024 64	0 60.0 — —	O O
	1280 x 1024 80	0 75.0 — —	O O
	1280 x 1024 91	1 85.0 — —	O O
	1400 x 1050 65	3 60.0 — —	O O
	1440 x 900 55	9 60.0 — —	O O
	1600 x1200	75.0	60	— — O O
	1920 x1080	67.2	60	— — O O
Apple Macintosh	640 x 480 35	0 66.7 — —	O O
	832 x 624 49	7 74.5 — —	O O
	1024 x 768 60	2 74.9 — —	O O
	1152 x 870 68	7 75.1 — —	O O
SDTV	480i	15.734	60.0	—	O	—	O
	576i	15.625	50.0	—	O	—	O
EDTV	576p	31.3	50.0	—	O	—	O
	480p	31.5	60.0	—	O	—	O
HDTV	720p	37.5	50.0	—		O	—
	720p	45.0	60.0	—		O	—
	1080i	33.8	60.0	—		O	—
	1080i	28.1	50.0	—		O	—
	1080p	67.5	60.0		—	O
	1080p	56.3	50.0		—	O

O: Frequency supported
—: Frequency not supported
The native resolution of the panel for the H1080 series is 1920 x 1080.
Resolution other than native resolution may display with uneven size of text or lines.

Projector Dimensions

REGULATORY COMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user's authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC-B, UL, cUL, CB, CE, CCC, KC, PCT, and C-tick