TFV18 - Drill Tryton - Free user manual and instructions

Product Type	Drill
Model	Tryton TFV18
Power Source	18V Li-Ion battery (sold separately)
Chuck Type	Keyless, 1.5-13 mm capacity
Speed Settings	Variable speed 0-550 RPM (low) / 0-1800 RPM (high)
Torque Settings	20+1 clutch positions
Forward/Reverse	Yes, with lock-off button
LED Work Light	Yes, integrated
Max Drilling Capacity (Wood)	25 mm
Max Drilling Capacity (Steel)	10 mm
Dimensions (approx.)	22 x 18 x 7 cm
Weight (without battery)	1.3 kg
Battery Type	Tryton 18V Li-Ion platform
Charger	Included with battery kit
Safety Features	Lock-off switch, overload protection
Maintenance	Clean with dry cloth; keep ventilation slots free of dust
Storage	Store in dry place, remove battery when not in use
Spare Parts	Battery, charger, chuck key (if applicable), carbon brushes
Included Accessories	User manual, warranty card
Warranty	2 years (subject to registration)

Frequently Asked Questions - TFV18 Tryton

What battery type does the Tryton TFV18 use?

The Tryton TFV18 uses an 18V Li-Ion battery, compatible with the Tryton 18V platform. Batteries and chargers are typically sold separately unless part of a kit.

What is the chuck capacity of the TFV18?

It features a keyless chuck with a capacity of 1.5 to 13 mm, allowing use with most common drill bits.

Is the speed adjustable on this drill?

Yes, the TFV18 has a two-speed gearbox (low: 0-550 RPM, high: 0-1800 RPM) and variable speed trigger for precise control.

How do I change the direction of rotation?

A forward/reverse switch is located above the trigger. Ensure the drill is fully stopped before switching direction.

Does the TFV18 have a torque control?

Yes, it has 20+1 torque settings for driving screws and a drill mode for high torque applications.

What materials can I drill with this drill?

You can drill wood (up to 25 mm), steel (up to 10 mm), and masonry (with appropriate bits). For masonry, use a hammer drill function if available; otherwise, use carbide-tipped bits.

How do I maintain the Tryton TFV18?

Keep the drill clean and dry. Clean the housing with a soft, dry cloth. Regularly check the chuck for debris. Store in a cool, dry place and remove the battery when not in use.

Where can I find replacement parts?

Replacement batteries, chargers, and carbon brushes are available from Tryton authorized dealers or online. Check the user manual for part numbers.

Is the TFV18 compatible with other brand batteries?

No, for safety and performance, only use Tryton 18V batteries. Using other brands may damage the tool and void the warranty.

What safety features does the drill have?

The TFV18 includes a lock-off button to prevent accidental start, an overload protection, and a safety clutch to reduce kickback in bind-up situations.

USER MANUAL TFV18 Tryton

E E K T R O N A R Z I

Line drawing of a 18V TRYTON electric drill putter with base (no text or symbols on the device body)

TFV12

TFV18

EN

Operating instruction

CORDLESS DRILL/SCREWDRIVER 3

PL

BEFORE YOU START USING THE MACHINE READ THOROUGHLY THIS MANUAL.

Keep this document for future reference.

WARNING! Read all safety warnings marked with a symbol ⚠️ and all operating safety instructions.

To limit the risk of fire, electric shock and injury while using the device, follow all operating safety instructions and tips provided below.

Keep all work safety instructions and tips for future reference.

In warnings provided herein the expression "power tool" means a power tool powered from the mains (with a power cord) or a battery powered power tool (cordless).

WARNING! General work safety warnings for use of the tool.

Workplace safety:

a) Keep your workplace tidy and well lit. Untidiness and bad lighting result in higher accident rate.
b) Do not use the power tool in explosive environments, created by flammable liquids, gases or dusts. The power tool generates sparks that can ignite dust or vapors.
c) Keep children and unauthorized persons away from the place where the power tools are used. Inattention may result in losing control over your power tool.

WARNING! General warnings regarding the use of power tools.

Electric safety:

a) Plugs used in power tools must match wall outlets. Never modify the plug of your power tool. Do not use any extension cables when operating a power tool with a grounding/earthing conductor (PE). Any modifications of plugs and outlets increase the risk of electric shock.
b) Avoid touching earthed surfaces or grounded items like pipes, heaters, central heating radiators and refrigerators. Touching earthed or grounded surfaces increases the risk of electric shock.
c) Do not expose your power tool to rain or damp environments. Water penetrating the tool increases the risk of electric shock.
d) Do not damage the power cord. Never use the power cord to carry, pull the power tool and do not pull by its power cord to disconnect plug from the outlet. Keep the power cord away from sources of heat, oils, sharp edges and moving parts. Damaged or entangled power cords increase the risk of electric shock.
e) When your power tool is operated outdoors use extension cords intended for outdoor use only. Using an extension cable intended for outdoor use decreases the risk of electric shock.
f) It is recommended to connect the device to a mains supply equipped with a residual current device (RCD) with a rated current of 30 mA or less.
g) When it is unavoidable to use your power tool in a damp environment use an RCD (Residual Current Device) for protection. The use of RCDs decreases the risk of electric shock.

WARNING! General warnings regarding the use of power tools.

Personal safety:

a) This equipment is not intended for use by persons (including children) disabled physically, mentally, sensorial or persons with no experience and knowledge in operating the equipment unless they operate the equipment under supervision or follow user's instructions provided by persons responsible for their safety.
b) It is necessary to predict steps, watch and keep common sense when using power tools. Do not operate power tools when you are tired, under influence of drugs, medicine or alcohol. A moment of inattention while operating a power tool may result in serious personal injury.
c) Use personal protective equipment (PPE). Always wear safety goggles. Wearing personal protective equipment (PPE) including a dust mask, anti-slippery footwear, a helmet and ear protection reduces personal injury.
d) Avoid unexpected start up. Before connecting your power tool to the mains and/or inserting a battery make sure its power switch is in off position. Carrying your power tool with a finger on its power switch or without disconnecting it from the mains (switched on) may result in an accident.
e) Before starting your power tool remove any keys/wrenches. Leaving a key/wrench in the rotating part of your power tool may result in personal injury.
f) Do not lean forward too far. Always remain stable and maintain balance. It will allow you to have a better control over your power tool in unpredictable situations.
g) Wear appropriate clothing. Do not wear loose clothes or jewelry. Keep your hair tied. Keep your clothes away from moving parts. Loose clothes, jewelry or long hair may be caught by moving parts.
h) If your power tool allows for using an external dust extraction or collection system, make sure it is connected and used properly. Using dust collectors may reduce dust affected risks.
i) Do not let your skills gained through the frequent use of the power tool make you overconfident and disregard safety rules. Carelessness may cause injury in a fraction of a second.

WARNING! General warnings regarding the use of power tools.

Use and taking care of your power tool:

a) Do not overload your power tool. Use a power tool with power adjusted to work being done. An appropriately chosen power tool will allow you to work better and safer under load it has been designed for.
b) Do not use a power tool when its power switch is out of order (it does not switch it on or off). Any power tool with its power switch out of order is dangerous and must be repaired.
c) Always disconnect the plug from the power source and/or disconnect its battery before changing any settings, performing replacement or storage. Such preventive measures reduce the risk of accidental power tool start up.
d) Keep your power tool out of reach of children and do not allow unauthorized persons to use the power tool. Power tools in hands of untrained persons can be dangerous.
e) Power tools require maintenance. Check power tools for concentricity or jamming of moving parts, any cracks and all

other factors affecting the power tool work safety. If any damage to the power tool is detected, it should be repaired before use. Improper power tool maintenance is a reason for many accidents.

f) Cutting tools should be sharp and clean. Keeping sharp cutting edges in good condition reduces the risk of jamming and facilitates operation.
g) Power tools, equipment, working tools etc. should be used according to this user's manual taking into account operating conditions and the work to be done. Misusing a power tool can result in dangerous situations.

h) At low temperatures and after a long brakes in operation it is recommended to turn the power tool to operate it with no load for a few minutes to provide proper grease distribution inside its driving mechanism.

i) Use soft, damp (cannot be wet) cloth and soap to clean power tools. Do not use petrol, solvents and other agents that may damage your equipment.

j) Power tools can be stored/carried after making sure that all moving components are locked and protected against release with original devices intended for this purpose.

k) Store power tools in a dry, dust and water-protected place.

1) Carry your power tool in its original packaging to provide protection against mechanical damage.

m) Keep handles and grip surfaces clean and free from oil and grease. Secure grip and control over the tool in unexpected circumstances are impossible if handles and grip surfaces are slippery.

WARNING! General warnings regarding the use of power tools.

Repair:

a) Warranty and post-warranty repairs of its power tools are carried out by PROFIX Service, which guarantees the best quality or repair and use of genuine spare parts.

WARNING! Cordless drill/driver, security warnings –

Personal Safety:

a) Use hearing protection when using drill/driver. Exposure to noise can cause hearing loss.

b) During work, when the power tool or drill might encounter a hidden electricity wire or its own lead, the power tool must be held by the insulated areas of the handle. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

c) Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock.

d) Do not work materials containing asbestos. Asbestos is considered carcinogenic.

e) Keep your workplace clean and tidy. Material mixtures are extremely dangerous. Light metal dusts can ignite or explode.

f) Protect the object machined. Make sure all clamps are closed and check for excessive clearance. It is safer to fix the object machined in a fixing device or a vice than holding it in your hand.

g) Always hold firmly the power tool with your both hands using both the main and auxiliary handle keeping a stable position. It is safer to control your power tool with both hands.

h) Turn the power tool immediately when the bit jams. Expect

intense vibrations that can result in a kickoff. The bit jams when the power tool is overloaded or is bent inside the object.

i) Before you put the power tool aside make sure it is completely stopped. The bit can jam resulting in losing control over the power tool.

j) Electric tools should be used exclusively with a unit of rechargeable batteries purposefully dedicated for power supply of them. Application of any other batteries may pose a risk of body injuries or a fire.

Safety instructions when using long drill bits:

a) Never use a speed higher than the maximum drill bit speed. Always start drilling at a low speed and after touching the workpiece to the drill bit. At higher speeds, the drill bit may bend if not in contact with the workpiece, resulting in injury.
b) Push the drill bit against the workpiece in line with the drill bit. Do not use excessive force. Drill bits may bend, causing damage and loss of control, which may result in injury.

WARNING! Safe use of rechargeable batteries and battery chargers -

Using the battery:

a) Use only the batteries that correspond to specifications required by the equipment manufacturer. Use of unsuitable batteries may lead to cracks and destruction of the battery, personal injuries or fires.
b) WARNING: In case of damage or improper use of the battery, explosive gases might be released. The battery must be kept away from fire and proper ventilation is to be assured during charging. It cannot be left for a longer period of time in a high temperature environment (areas with strong exposure to the sun, close to radiators or any other place with a temperature above 40 degrees).
c) The battery must be charged within the temperature range of 15 to 25°C.
d) Batteries can be charged exclusively with use of a power adapter recommended by the manufacturer of the tool. Application of any other power adapter may pose a risk of a fire.
e) Never expose the battery to the effect of water or moisture.
f) When another battery is to be charged in sequence the time gap between charging operations must be not less than 30 minutes.
g) In no case may you open the battery.
h) Under unfavourable conditions electrolyte may leak from batteries, be careful to avoid contacts with the liquid. In case of accidental contacts with the liquid wash the affected locations with water. When liquid penetrates eyes, seek also for medical assistance. The liquid that leaks from batteries may be a reason for irritation or scalds.
i) When the battery unit is not in use keep it far away from metallic items such as paper clips, coins, keys, nails, bolts or other metal things that may short the battery terminals. Shorts of battery terminals may cause burns or fires.
j) Never throw batteries to fireplaces.
k) Never charge a damaged battery.

The batteries are intended for multiple use and contain harmful lithium.

Upon the battery lifetime expires the battery must be disposed in accordance with environmental regulations. Discharge the

battery first top the empty state and remove from the electric tool. Hand over to an organization that deals with utilization of batteries or take it back to the shop where the tool had been purchased.

Using the charger:

a) Use only dedicated power adapters to charge the battery. Application of a power adapter dedicated to charge another type of the battery unit poses a risk of fires.

b) The supplied charger should only be used for charging batteries that are supplied together with it. Charging other batteries may cause breaking and disintegration of the battery, bodily harm, or fire.

c) Do not disassemble the charger.

d) The charger is designed exclusively for indoor use. It must not be exposed to water or moisture.

e) Charge only in an ambient temperature between 15-25 degrees.

f) Do not insert metal objects of any kind into the charger.

APPLICATIONS AND CONSTRUCTION:

The device is dedicated to drive in and out screws, drilling boreholes in such materials as steel, wood, plastics, etc. The combo drill and screwdriver is designed exclusively for DIY applications.

The tool must not be used for work requiring a professional tool.

Any use of the device that is not in observance with the above-mentioned purpose is forbidden, leads to the loss of warranty, and relieves the manufacturer from responsibility for the resulting damage.

Any modifications of the tool by the user relieve the manufacturer from responsibility for any damage and injuries to the user and the surroundings. Despite using the tool according to its intended application it is impossible to eliminate certain residual risk factors. Considering the tool construction the following risks may occur when operating the tool:

- Touching the rotating drill bit with the hand or operator's clothes.

- Burns when changing drill bits (Drill bits heat up intensely during operation; use protective gloves when changing the drill bit).

- Throwing back machined object or its fragment.

- Bending/breaking the drill.

■ The set contains:

• Cordless drill/screwdriver -1pc.

- Battery - 1 pc.

- Charger pc.

- Working bits set -magnetic tip for bits with a 1/4" holder1 pc. -bits -6pcs (PH1, PH2, PZ1, PZ2, SL5, SL6) -drills -6pcs (1,5; 2,5; 3; 4; 5; 6mm)

- Carrying case -1pc.

- Warranty card-1 pc.

- Operating instruction -1pc.

■ Device components

The numbering of device components refers to graphics presented on page 2 of the user's manual:

Fig.A 1. Keyless chuck

1. Clutch control knob
2. Battery capacity indicator
3. Rotation direction switch
4. Handle
5. Fastener to hang on the belt
6. Battery
7. Battery lock clip
8. On/off switch
9. Auxiliary lighting

Fig.C11. Charger

Fig.F 12. Clutch setting indicator

1. Drilling setting pictogram

Fig.G 14. Left-threaded fixing screw

TECHNICAL PARAMETERS:

MODEL	TFV12	TFV18
Supply voltage	DC 12 V	DC 18 V
Rotation speed under no-load conditions	0-700 rpm
Chuck clamping range	0,8-10 mm
Weight (with battery)	1,030 kg	1,135 kg
Sound pressure level (LpA)	81 dB(A)
Sound power level (LwA)	92 dB(A)
Tolerance of measurements KpA, KwA	5 dB(A)
Vibration level according to: EN 62841-1-2 (tolerance of measurements K=1,5 m/s ^2 )	a_h,D=2,29 m/s^2
Battery type	Li-ion
Rated voltage	12V	18V
Electric capacity	1500mAh
Battery charger
Mains voltage	100-240 V
Frequency	50/60 Hz
Power consumption	5W	8W
Output current (DC)	15V/0,33A	21,5V/0,37A
Charging time	3-5 h

The vibration level value given refers to basic application of the tool. If the tool is used for other applications or with other tools, or if it is not maintained properly, the vibration level may differ from the values given. The above-mentioned causes may lead to higher exposure to vibrations during the whole work time.

One must implement additional safety measures to protect the operators from exposure to vibrations, such as maintenance of the electric tool and work tools, assurance of proper hand temperature, or determination of the sequence of work operations.

The declared total vibrations and declared noise emissions were measured in accordance with a standard test method and may be used for tool comparison.

The declared total vibrations and noise emissions can be used in preliminary exposure assessment.

Warnings:

The vibrations and noise emissions during the actual use of the power tool may differ from the declared values depending on how the tool is used and on the type of the workpiece in particular.

Determine safeguards to protect the operator. They should be based on the estimated exposure under actual operational conditions (taking into account all parts of the operating cycle such as when the tool is switched off or idle except the start time).

PREPARATION FOR WORK:

■ Charging the battery

The driver is supplied with a partially charged battery. Charge the battery fully before use. It is recommended that the first charging session lasts at least 5 hours.

1. Press the battery lock button (8) and remove the battery (7) from the

drill-driver (see fig. B).

1. Connect the battery (7) to the charger (11) (see fig. C).
2. Connect charger to an electrical socket 100-240 V, 50/60Hz.

■ Battery charging indicator

The red battery lamp is lit during the charging process. When the battery is fully charged, the red lamp goes out and the green one is lit. The charging current reduces with the charging progress. After about 3 hours the charging current reaches the stable, minimum value (trickle charging) to prevent battery overcharging and damage.

After charging, disconnect the charger and remove the battery.

The lithium-ion battery can be charged at any moment, without detriment to its life. Interrupting the charging process does not entail a risk of damaging the battery cells.

IN USE:

■ Turning on/off

The switch (9) has fluid rotation speed adjustment built-in. Press the switch to activate the power tool. The rotation speed will increase the further the switch is pushed. To stop the power tool, release the switch.

■ Battery capacity indicator

The battery capacity indicator (3) indicates the battery is empty with two LEDs.

Green LED is lit:

The battery is fully charged.

Green and red LEDs are lit:

The battery is sufficiently charged.

Only red LED is lit:

The battery is empty, it needs charging.

■ Choosing rotation direction (see Fig. E)

The driver can work with clockwise (right) or counter-clockwise (left) rotation.

• to select clockwise rotation, move the clockwise/counter-clockwise slider (4) to the left (looking from the back of the driver),
• to select counter-clockwise rotation, move the clockwise/counter-clockwise slider (4) to the right (looking from the back of the driver), When the rotation direction switch is in the middle position, it is locked. For drilling and driving screws in, clockwise operation should be selected. For taking out the drill bit, removing a stuck drill bit, or unscrewing screws, counter-clockwise operation should be selected.

■ Choosing torque (see Fig. F)

The driver is equipped with a ring (2), which can be used for setting the torque when driving screws. The ring has 22 settings, from 1 to 21, and a drilling setting.

Using a given setting (from 1 - 21) means that the clutch is set to an assigned torque. This makes it possible to prevent a screw from being driven too far or being damaged. Different torques should be used for different screws and materials.

Always start with a low torque and increase gradually until the desired result is achieved.

For drilling in metal, wood or plastic, set the ring (2), so that the indicator (12) points to symbol (13).

■ Changing the chuck ( Fig. G)

1. Disconnect the battery (7) from the driver.

2. Open the chuck as much as possible (1)

3. Using a PH2 (Philips No.2) screwdriver, rotate the fixing screw (14) of the chuck clockwise (CAUTION! Left-thread). To free a seized bolt hit is gently on its head.

4. Hold the lower chuck ring (the one closer to the driver body) and rotate the drill/driver chuck counter-clockwise (looking from the point of view of the chuck).

CAUTION: A jammed keyless chuck (1) can be released by inserting the short end of a hex key in the chuck and lightly tapping the longer arm of the key (see Fig.D).

1. To attach the chuck, screw it onto the drive spindle counter-clockwise (looking from the chuck side) and secure by screwing in the fixing screw counter-clockwise using a PH 2 screwdriver (No.2 Philips). For the chuck not to rotate during screwing in the fixing screw, the chuck should be held by the lower ring (the one closer to the drill/driver body).

■ Auxiliary components

• The practical fastener (6) can be used for attaching the drill-driver on the user's belt, both for right-hand and left-hand dominant users.
• The drill/driver is equipped with an auxiliary light (10) for the area of drilling/driving, which turns on after the appropriate switch (9) is pushed.

■ Work tool replacement

CAUTION: Disconnect the battery from the driver or put the rotation direction switch (4) in the middle position to secure the machine from being started by mistake, which could in turn cause harm to the user.

When the tool switch (9) is released the drill chuck is locked. It enables quick, easy and convenient replacement of a working tool installed in the drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate the chuck ring anticlockwise to expand the opening of the chuck. Insert a new drill (or a working bit) into the chuck and rotate the chuck ring clockwise to secure the drill in the drill chuck.

Drills (or other working bits) must be moved to the full depth of the chuck opening.

■ Drilling boreholes

1. To drill deep boreholes carry out your job gradually, drill to lower depths and remove the drill from the borehole from time to time to remove borings from the borehole.
2. To drill large diameter boreholes it is recommended to start with drilling a low-diameter borehole and then expand it to the desired diameter. It prevents the tool from overloads.
3. When the drilling bit is seized during working switch immediately the tool off to prevent it from being damaged. Switch the rotations direction to the anticlockwise rotations and then remove the drilling bit from the borehole.
4. Keep the drill aligned with the axis of the borehole. The drilling bit must be positioned perpendicularly to the surface of the machined material. When the perpendicularity fails to be maintained the drilling bit may be seized or broken or, under extreme circumstances, the operator may be injured.
   Rotation speed of the drill spindle is controlled by the force the power switch is depressed with.

■ Driving screws

It is recommended to drill the pilot borehole first. The pilot borehole must be a little deeper and with a less diameter than the outer diameter of the

screw thread. When the screw is to be driven within the vicinity of the material edge the pilot borehole prevents from undesired chipping of the material.

If the screw is driven with abnormal difficulty the screw must be retracted and the pilot borehole diameter should be enlarged.

Anyway, when problem to drive the screw in persists (e.g. in case of hard wood grades) try to use a lubricating agent (e.g. liquid soap). Press the tool to the screw with sufficient force to avoid spontaneous rotation of the driving bit in the screw head. Use only those bits that accurately match the bit head. When the screw head is damaged further driving the screw in or out may prove infeasible.

STORAGE AND MAINTENANCE:

The tool in principle does not require any special maintenance or service. The tool must be stored in a place that is not accessible to children and must be kept clean and protected from moisture and dust. The storage conditions should prevent potential mechanical damage and impact of the weather conditions.

CAUTION: Remember to always disconnect the battery from the tool prior to starting the cleaning operations and unplug the charger from the outlet. The charger may be cleaned exclusively with use of a dry cloth.

Use also a clean cloth to clean regularly the ventilation openings of the tool to keep them patent. From time to time disassemble the grip and remove dust and other rubbish from the interior.

The tool housing must be cleaned with use of a moistened cloth small quantity of soap and then wiped dry. Do not use any detergents or solvents as they can damage parts made from plasticsAfter cleaning let the tool dry completely before it is used again.

TRANSPORTATION:

Store and transport the tool in its transport box to protect it against humidity, dust penetration and small objects; remember to protect its ventilation openings. Small objects after getting into the casing can result in damage to the motor.

PROTECTION OF THE ENVIRONMENT:

NOTE: The symbol nearby denotes that old equipment must never be thrown away together with other waste (with the penalty of a fine). Hazardous components of electronic equipment may adversely affect the natural environment and

human health.

Each household may contribute to the recovery and reuse (recycling) of old machinery and equipment. Both in Poland and Europe a system for recovery of used equipment either exists or is being created. The system obliges all organizations that sell such equipment to collect the used machinery and appliances. Moreover, general purpose collecting points for such equipment are available.

PICTOGRAMS:

Explanation of the icons located on the nominal plate and the information tags:

«Read this instruction before switching on the power supply and starting the work»

«Protect the battery against heat, e. g., against continuous intense sunlight.»

in-fire.»

This appliance is in conformity with national and European standards as well as with general safety guidelines.

Any repairs are allowed to be carried out exclusively by qualified staff with use of original spare parts.

TROUBLESHOOTING GUIDE:

PROBLEM POSSIBLE	CAUSE REMEDY
The tool (drill/screwdriver) fails to operate.	No power voltage, damaged motor or the power trigger.	Check the battery status, recharge or replace with a new one when necessary.When the problem persists hand over the tool for repair at a service workshop.Please refer to the warranty sheet for addresses of authorized workshops.
Irregularities of the motor operation.	Battery low. Recharge the battery.
	Worn carbon brushes of the motor.	Have the brushes replaced at a service workshop.

The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the company reserves the right to make amendments to the product specification without a prior notice. The images included into the operation manual are only of the exemplary nature and may slightly differ from actual appearance of the device purchased. This instruction manual is protected by copyright. Copying it without the written consent of PROFIX Co. Ltd. is prohibited.

INSTRUKCJA OBSŁUGI

WIERTARKO - WKRETARKA AKUMULATOROWA: TFV12, TFV18

Deg zalā un sarkanā LED diode:

Deg tikai sarkanā LED diode:

(EN) EC/EU DECLARATION OF CONFORMITY

(PL) DEKLARACJA ZGODNOŚCI WE/UE

(RO) DECLARATIE DE CONFORMITATE CE/UE

(LV) EK/ES ATBILSTIBAS DEKLARACIJA

(LT) EB/ES ATITIKTIES DEKLARACIJA

(CS) ES/EU PROHLÁŠENÍ O SHODĚ

(HU) EK/EU-MEGFELELŐSÉGI NYILATKOZATA

(EN)

MANUFACTURER

(PL)

PRODUCENT

(RO)

PRODUCATOR

(LV)

RAŽOTĀJS

(LT)

GAMINTOJAS

(CS)

VÝROBCE

(HU)

GYÁRTÓ

PROFIX Sp. z o.o. ul. Marywilska 34, 03-228 Warszawa

(EN) Person who was authorized to develop technical documentation:

(EN) 2006/42/EC (OJ L 157, 9.6.2006, p. 24–86); 2014/30/EU (OJ L 96, 29.3.2014, p. 79–106); 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110) change 2015/863/UE;

(EN) and have been manufactured in accordance with the standards:

Representative of the Board for Certification