SDSTX3110-121-LRT-B - Server Milan - Free user manual and instructions
Find the device manual for free SDSTX3110-121-LRT-B Milan in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rackmount Server |
| Brand | Milan |
| Model | SDSTX3110-121-LRT-B |
| Form Factor | 2U Rackmount |
| Dimensions (WxDxH) | 430 x 650 x 88 mm (16.9 x 25.6 x 3.5 in) |
| Weight | 15 kg (33 lb) |
| Processor | Intel Xeon Scalable (2nd Gen) up to 28 cores |
| Memory | Up to 512 GB DDR4 ECC RDIMM (16 slots) |
| Storage | 8x 3.5" SATA/SAS hot-swap bays |
| RAID Support | Hardware RAID 0/1/5/6/10 |
| Networking | Dual 10GbE SFP+ and dual Gigabit Ethernet |
| Expansion Slots | 3x PCIe 3.0 x16, 2x PCIe 3.0 x8 |
| Power Supply | Dual redundant 500W hot-plug (80+ Platinum) |
| Cooling | 4x hot-swap system fans |
| Remote Management | IPMI 2.0 with dedicated LAN |
| Operating System | Supports Windows Server, Linux, VMware |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Safety Certifications | CE, FCC, UL |
| Maintenance | Tool-less access to internals, hot-swap components |
| Spare Parts Availability | PSU, fans, HDD caddies, memory, RAID controller |
| Reparability | Modular design; firmware updates via IPMI |
Frequently Asked Questions - SDSTX3110-121-LRT-B Milan
What is the default login for the IPMI remote management?
The default IPMI username is admin and password is admin. It is recommended to change these upon first login.
How do I reset the BIOS/UEFI settings to factory defaults?
During boot, press F2 to enter BIOS setup. Navigate to 'Save & Exit' and select 'Restore Defaults'. Save and exit.
Can I use regular SATA drives in this server?
Yes, the server supports both SATA and SAS drives in the hot-swap bays. Ensure correct backplane configuration; SATA drives work with the onboard SATA controller.
What is the maximum supported memory capacity?
The server supports up to 512 GB using 16 x 32 GB DDR4 ECC RDIMM modules.
Does the server support hot-swap power supplies?
Yes, the dual power supply units are hot-swappable and support redundancy. You can replace one without powering down the server.
How do I configure RAID after installing drives?
During boot, press Ctrl+R (for LSI RAID) or Ctrl+H (for adaptec) to enter RAID configuration utility. Create virtual disks as needed.
What is the power consumption of this server?
Typical power consumption is around 350W under load, with a maximum of 500W from each PSU.
How do I update the firmware?
Firmware updates are performed via the IPMI web interface under 'Maintenance' > 'Firmware Update'. Download the latest firmware from Milan support site.
Is the server compatible with VMware ESXi?
Yes, it is certified for VMware ESXi 6.5 and later. Check Milan's hardware compatibility list for specific versions.
What do I do if the server does not power on?
First, check power cables and ensure PSUs are plugged in and switches on. Then check the front panel LED: if amber, there is a fault. Press the ID button to locate the server. If no LEDs, verify AC power source.
User questions about SDSTX3110-121-LRT-B Milan
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual SDSTX3110-121-LRT-B - Milan and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SDSTX3110-121-LRT-B by Milan.
