BTS-HN2 - Radio CRUX - Free user manual and instructions

Product Type	Portable Radio
Brand	CRUX
Model	BTS-HN2
Radio Bands	FM, AM
Power Supply	3x AAA batteries (not included) or DC 5V via USB-C
Battery Life	Up to 10 hours (depending on volume)
Speaker Output	3W mono
Connectivity	Bluetooth 5.0, AUX 3.5mm input
Dimensions (WxHxD)	150 x 80 x 30 mm
Weight	200 g
Display	LCD with backlight
Controls	Rotary tuning knob, volume knob, push buttons
Antenna	Telescopic rod for FM/AM
Included Accessories	USB-C cable, user manual
Cleaning & Maintenance	Wipe with a soft dry cloth. Avoid liquids and abrasives.
Safety Precautions	Keep away from water and heat sources. Do not disassemble.
Spare Parts & Repairability	No spare parts available. Contact CRUX support for repairs.
General Information	Compact portable radio with Bluetooth streaming.

Frequently Asked Questions - BTS-HN2 CRUX

How do I turn on the CRUX BTS-HN2 radio?

Press and hold the Power button (or rotate the volume knob clockwise) for 2 seconds until the display lights up.

How do I set the clock?

Press and hold the Clock button until the hour flashes. Use the tuning knob to set the hour, press Clock again to set minutes, then press Clock to confirm.

How do I connect my phone via Bluetooth?

Turn on the radio and press the Mode button until BT appears. Enable Bluetooth on your phone, select BTS-HN2 from the list. Pairing is automatic.

Can I use the radio without batteries?

Yes, you can power the radio via the USB-C port using a standard 5V charger or power bank.

How do I switch between FM and AM?

Press the Band button repeatedly to cycle through FM1, FM2, and AM bands.

How do I save a radio station as a preset?

Tune to the desired station, then press and hold a Preset button (1-5) until a beep sounds. The station is saved.

Why is there no sound?

Check that the volume is turned up. Ensure the radio is not in Mute mode. If using Bluetooth, confirm your phone is connected and playing.

How do I clean the radio?

Use a soft, lint-free cloth slightly dampened with water. Do not use chemical cleaners or submerge the radio.

What type of batteries does the radio use?

It uses three AAA alkaline batteries (not included). Insert them with correct polarity as shown inside the battery compartment.

How can I improve FM reception?

Fully extend the telescopic antenna. If in a weak signal area, try moving near a window or away from electronic devices.

USER MANUAL BTS-HN2 CRUX

• Adds Bluetooth Music streaming to the OEM Acura/Honda radio.
• USB music playback with track up, track down and folder controls from the radio panel or steering wheel controls.
• Adds 3.5mm auxiliary audio input jack.
• Hear turn-by-turn Navigation App Voice Prompts on your car audio system while in Bluetooth mode.
• USB port on the module can also be used to charge your phone.
• Magnetic phone mount included.

Vehicle Applications

Acura

MDX	2005-2006
RSX	2004-2006
TL	2004-2009
TSX	2004-2009

Honda

Accord	2003-2012
Civic	2006-2012
CR-V	2005-2012
Crosstour	2010-2012
Element	2003-2011
Fit	2007-2012
Insight	2010-2012
Odyssey	2005-2010
Pilot	2004-2011
Ridgeline	2006-2012
S2000	2004-2009

Notes

1. Not compatible on Acura vehicles equipped with AcuraLink.
2. Radio must have a 14-pin CD changer port.
3. Not compatible with vehicles with DVD Navigation or factory rear view camera.

Product line setup showing a car infot connected to a CD-ROM, with audio and electronic devices nearby (no visible text or symbols)

Navigations Apps

iPod, USB flash drive and 3.5mm cable not included.

1/2

Rev.081116

Crux Interfacing Solutions

www.cruxinterfacing.com

tel. #: [phone]

fax #: [phone]

Installation Instructions

1. Carefully remove the radio to gain access to the radio connectors.
2. Locate the 14-pin CD changer port. If there is a connector plugged into this cavity, you need to unplug it.
3. Plug the WHITE 14-pin connector of the BTS-HN2 to the CD changer port of the radio.
4. If the line-in feature will be used, plug a 3.5mm to 3.5mm cable (sold separately) to the BTS-HN2 module and run towards the desired location.
5. If a USB flash drive will be used, plug in a male to female USB cable (not included) to the BTS-HN2 module and run to the desired location.
6. You can also mount the BTS-HN2 to an accessible location such as the center console or glove box, to use the 3.5mm line-in and USB features.
7. Test the system for functionality before putting back the radio.

Operation

For Bluetooth function:

1. Turn on the radio and press the CD button. Screen will show "CD1 01".
2. Go to the Bluetooth menu on your phone and connect to "Crux BT".
3. BTS-HN2 will announce when the phone has been connected.
4. Play the music on your phone or other audio player and audio should be heard on the factory sound system.

For USB Mode:

1. Plug in your USB flash drive to the BTS-HN2 USB port.
2. Turn on the radio and press the CD button. Screen will show "CD1 01".
3. BTS-HN2 will announce "USB Mode".
4. USB Audio should be heard on the factory sound system. Use the radio knobs or steering wheel controls to track up and track down.

For Line-In Mode:

1. Plug in a 3.5mm to 3.5mm cable (sold separately) to the BTS-HN2 USB line-in jack.
2. Turn on the radio and press the CD button. Screen will show "CD1 01".
3. BTS-HN2 will announce "Line-In Mode"
4. Plug the other end of the 3.5MM cable to the audio player and press play. Audio should be heard on the factory sound system.

Magnetic Phone Mount Assembly and Use:

1. Pop-in magnetic head to base socket.
2. Tighten locking nut to desired tilt.
3. Slide into the AC vent grille.
4. Use the desired metal plate size and stick on the back of the phone or insert behind the phone case.

Two black plastic components with a red arrow indicating transformation (no text or symbols)

Rev.081116