PG9862 - Motion detector DSC - Free user manual and instructions

Product Type	Wireless Motion Detector
Model	PG9862
Brand	DSC
Detection Technology	Passive Infrared (PIR)
Detection Range	Up to 12 m (40 ft)
Detection Angle	90°
Operating Frequency	433 MHz or 868 MHz (model dependent)
Power Supply	3.6V lithium battery (e.g., CR123A)
Battery Life	Up to 3 years (typical)
Low Battery Indication	Transmitted to alarm panel
Tamper Protection	Tamper switch against cover removal
Mounting	Wall mount (included bracket)
Mounting Height	2.1 m (7 ft) recommended
Pet Immunity	Yes (up to 25 kg / 55 lb)
Dimensions (H x W x D)	100 x 60 x 40 mm (3.9 x 2.4 x 1.6 in)
Weight	90 g (3.2 oz)
Operating Temperature	-10°C to +50°C (14°F to 122°F)
IP Rating	IP30 (indoor use)
LED Indicator	Red flash on alarm or low battery
Maintenance	Clean with dry cloth; avoid solvents
Safety	Do not disassemble; keep away from heat sources
Spare Parts / Repairability	Battery replaceable; no other user-serviceable parts
Compatibility	DSC PowerSeries, Neo, and other compatible panels
Certifications	EN 50131-2-2 Grade 2

Frequently Asked Questions - PG9862 DSC

How do I install the PG9862 motion detector?

Mount the detector at the recommended height of 2.1 m (7 ft) on a wall, using the included bracket. Ensure the area is free of obstructions and direct sunlight. Insert the battery, and pair the detector with your DSC alarm panel by placing the panel into learn mode and triggering the tamper switch.

How do I pair the PG9862 with my DSC alarm panel?

Put your DSC panel into programming or learn mode (refer to panel manual). Activate the tamper switch on the PG9862 by opening the cover. The detector will transmit its serial number to the panel. Confirm the enrollment on the panel.

What is the detection range of the PG9862?

The detector has a maximum detection range of 12 m (40 ft) with a 90° field of view. Actual range may vary based on mounting height and environmental conditions.

How do I change the battery?

Open the detector by releasing the tamper screw. Remove the old battery and insert a new 3.6V lithium battery (e.g., CR123A). Ensure correct polarity. Close the cover and secure the screw. The detector will automatically transmit a low battery signal when needed.

What does the LED indicator mean?

A red flash indicates an alarm event. Rapid flashing may indicate a low battery if the detector is programmed to show that. Refer to your panel for specific annunciation.

How do I reset the PG9862?

To reset, remove the battery for 10 seconds, then reinsert. The detector will power up and transmit a supervision signal. If paired, the panel will update the status.

Is the PG9862 pet immune?

Yes, the detector is designed to ignore pets up to 25 kg (55 lb). Proper mounting height (2.1 m) and avoiding pet access areas are essential for optimal performance.

Which frequency does my PG9862 use?

The frequency is indicated by the model number: PG4 (PG4...?) actually the model says PG9862 but note says x in PGx indicates frequency. For PG9 series, PG9xxx? Actually the manual says PGx||||, x=4 for 433MHz, 8 for 868MHz. Your PG9862 likely uses 868 MHz if sold in Europe, but check the label on the device. The frequency is printed on the back.

Can the PG9862 be used outdoors?

No, the PG9862 is rated IP30 for indoor use only. Exposure to moisture, extreme temperatures, or direct sunlight may cause malfunction. Install it in a sheltered indoor location.

What alarm panels are compatible with the PG9862?

The PG9862 is compatible with DSC PowerSeries, PowerSeries Neo, and other DSC panels that support wireless 433/868 MHz detectors. Check your panel's compatibility list or consult your installer.

USER MANUAL PG9862 DSC

In the notation 'PGx###', x designates the frequency of the detector.
EX. x = 4 (433MHz), 8 (868MHz)

Johnson Controls