PG9872 - Motion detector DSC - Free user manual and instructions

Product Type	Wireless Motion Detector
Brand	DSC
Model	PG9872
Dimensions	Approx. 10 x 6 x 4 cm
Weight	Approx. 100 g (including battery)
Power Supply	1x CR123A 3V Lithium Battery
Battery Life	Up to 3 years typical
Detection Range	Up to 12 meters (40 ft) at 90°
Pet Immunity	Up to 25 kg (55 lbs)
Operating Frequency	433 MHz (EU) / 915 MHz (US)
Tamper Protection	Rear and cover tamper switch
Compatibility	DSC PowerSeries, Neo, and HS Series panels
Installation Height	2.0 - 2.5 m (6.5 - 8 ft) recommended
Operating Temperature	-10°C to 50°C (14°F to 122°F)
Humidity	Up to 95% non-condensing
Maintenance	Clean lens with soft dry cloth; test weekly
Safety Features	Low battery notification, tamper alarm
Spare Parts	Battery (CR123A), mounting brackets available
Repairability	Battery replaceable; no user-serviceable parts inside
Certifications	CE, FCC, UL
Warranty	2 years limited

Frequently Asked Questions - PG9872 DSC

How do I install the DSC PG9872 motion detector?

Mount the detector at the recommended height of 2.0-2.5 m (6.5-8 ft) using the included bracket. Ensure the lens is unobstructed and the detector is level. Insert the CR123A battery and pair with your DSC alarm panel following the panel's instructions.

What type of battery does the PG9872 use and how long does it last?

It uses one CR123A 3V lithium battery. Under normal conditions, the battery lasts up to 3 years. Replace the battery when the panel indicates a low battery signal.

What is the detection range of the PG9872?

The detector can sense motion up to 12 meters (40 ft) with a 90° wide-angle lens. The actual range may vary based on installation environment.

Is the PG9872 pet immune?

Yes, it is pet immune up to 25 kg (55 lbs) when installed correctly. Avoid pointing the detector towards stairs or areas where pets can climb near the mounting height.

Can the PG9872 be used outdoors?

No, it is designed for indoor use only. Exposure to rain, snow, or direct sunlight may damage the detector and void the warranty.

How do I pair the PG9872 with my DSC alarm panel?

Enter programming mode on your DSC panel (e.g., PowerSeries: press * and then installer code). Add a wireless zone, then follow the panel prompts. Insert the battery in the detector to send a supervision signal. Refer to the panel manual for exact steps.

What should I do if the detector is triggering false alarms?

Check for obstructions, pets, HVAC vents, or direct sunlight. Ensure the detector is mounted at the correct height and away from heat sources. Clean the lens with a dry cloth. Adjust the sensitivity if your panel allows.

How do I test the PG9872?

Walk across the detection zone at the far end of the range. The panel should show an alarm or trip the zone. Test weekly to ensure proper operation. Also activate the tamper switch to verify tamper protection.

What does the tamper feature do?

The detector has rear and cover tamper switches. If the detector is removed from its mount or the cover is opened, a tamper alarm is sent to the panel, indicating unauthorized access.

Is the PG9872 compatible with all DSC alarm panels?

It is compatible with most DSC wireless panels, including PowerSeries, Neo, and HS Series. Check the panel's wireless compatibility list or the detector's manual for specific models.

USER MANUAL PG9872 DSC

The IC#072 is a group mission, along

The PRA72 is a smart wireless earling. The presence security (selected mode) that creates a 360° coverage area in detectable or introders in indoor areas. The detectors have the following features:

• Presence detection made - active 15 minutes after installation

(power-up) and then only when the panel is in Disarm made.

• Security detection made - operates as a normal motion security

detector

• Built-in link quality indicators eliminate the need for the installer

physically approach the control panel and reduce installation tin

• The device supports temperature and light level reports to com-

patible alarm systems that support temperature and light sensors.

• Tamper protection.

• Power: two-way. Frequency. Hopping. Spread. Spectrum. THSS.

TDMA technology.

• The Advanced True Motion Recognition™ algorithm (patented) also select the desired Zone Number

triquishes between the true motion of an intrader and any other dis-

turbeness which may cause false alarms.

NOTE: For 1.1. installations, the detector is for use with UI trol units only.

Legend

①

A LEDs

B Light

C. Batter

D. Tampel protection

Г. Руто sensor

Figure 1. Internal view

Inserting or replacing the battery

To insert the batteries, complete the following steps.

1. To separate the detector from the mounting bracket, rotate

bracket anticlockwise and pull it from the detector.

1. Insert the battery while observing polarity.

2. OFFIC is the battery is always installed, will the ineler

NOTE: It is clearly in truth, hence, put the object that requires from the back of the detector.

1. Align the bracket, rabs with the detector, slots and rotars

2. High the market banks with the lenders, more and more clear closing to verify that it is securely attached.

CLOCK-ISO - to - Perity - HAC - R - 25 - Security - at least

Figure 2. Removing the bracket

NOTE: If a screw is used to secure the detector to the bracket must Do not partially or completely observe the detector's

Figure 3) open the screw screw and remove the screw to computer.

the detector lives the momentum bracket ensure the screw rowWARNING! To currently with FCC and ISED Consels RF current room

fully seen or fully closed and rotate the detector anisolarization requirements the FIR detector should be located at a distance.

Replace the battery casting polarity is observed. Replace the of at least 20 cm front all persons during normal operation. The following table outlines the detection distance in relation to the detector and secure to the bracker with the screw. has used for this product must not be co-located or operated in non-height.

NOTE: It is recommended to pair almost 1 minute after bestijection with any other antenna or transmitter.

removal before insertout the new battery NOTE: The PGX872 Wireless ceiling PIR presence/security detector

shall be installed and used within an environment that provides the

Caution! Risk of explosion if battery is replaced by an incorpmodulotype degree max 2 and average values category II in NON Dispose of used batteries according to the manufacturer's instruction/ARDOUS LOCATIONS. The equipment is designed to be and according to local rules and regulations. Installed only by qualified service persons.

Enrollment

Refer to the panel installation manual for the enrollment procedure installation and Classification of Residential Barglar Alarm System. A general description of the procedure is provided in the following 1641.

flow chart:

dStapor Procedure

st. Write the installation manual for the alarm system that the

device is being coralled on to ensure that the proper

src: usarl

1. Enter the Device Enrollment option through the specified

method and select the appropriate option to add the

urity device

12.3.2017年

1. Part-time device by either inverting the battery to power installer to

the device that the enrollment is persisted, of by eft

Device ID.

Full the curriculum was of which the battery to power device and begin the auto-enrollment process.

1. 2017年1月1日

NOTE: You can also enter ID:XXX-XXXX (the numb

the device that is printed on the label), if the devic

sautomatically error.

ct the desired Zone Number

dis.

Fig. 10. The following parameters: W_p is the result

the and test the detector. See With testing / local at

gustie testing for the manufacturer on testing the device.

is enrolled on for other Inst procedures that are required

1. 2013-05-08 19:17 19:17 19:17 19:17 19:17 19:17

NOTE: If the detector is already enrolled, you can configure

detector parameters by programming the system. See the alarm

installation manual for more information about device parameters

NOTE: When corolling the IX8972 detector to wireless panels

(WPSOXX) with version 19.4 or lower, the detector will be

motion detector, ID 120-xxxx, and labelled 'Motion Sens' in

Installation, fins

Use the following

2.2.1

strip 7

Figure 3. General guidelines

1. Keep away from heat sources.

2. Do not expose to air drails.

3. Do not install outdoors

4. 2017年1月1日（星期二）至2017年1月31日

5. Avoid direct sunshine.

6. Do not install near high voltage electrical lines

7. Do not install behind partitions

8. Mount on a solid cable surface

2017年1月1日

WARNING: DO not partially be completely obscure the detected

[Unreadable]

WARNING! To comply with FCC and ISED Canada RF exposure com

pharix requirements, the F1K (local) should be located) at a distance

of at least 20 cm from all persons during northern operation. The cancer-

has used for this product must not be sa-

Sanction with any other antigen of transfection.

NOTE: The PGx872 Wireless ceiling PIR presence/security detector

shall be installed and used within an environment that provides the

Walk testing / local diagnostic testing

Before permanently mounting any wireless device, temporarily

the device and perform a walk test. Perform a walk test o

center area at least once a week to ensure that the director

carnavik

After inserting the battery or closing the bracket, the detector

matically enter a stability period where the LED flashes REIC

ew seconds. Walk rest the coverage area the LED lights red at

own station is detected followed by 1 LED, likely. The

you thought is detected followed by LED shades. The cor

1.1.13 Brinks indicate the received signal strength in walk-test

Regardless in the 1.1-17 Selection Status, the 1.1-13 rights upon

motion detection. After 15 minutes the detector automatically

(1)

The following table indicates the received signal strength.

IMPORTANT: Only GOOD or STRONG signal strengths are accept-

able. If you receive a PODR signal from the device, re-locate it and

dFirst until a GOOD or STRONG signal is received.

SYSTEM NOTE: For HL/TLC installations only, STRONG signal levels are

currentable. Plus, installations, certificate, the target, environmentals, and one

acceptable. After mathematical check, the product functionally in your

junction with the incompatible devices HSM2HOS19,

HS2ECN3HP19, PC492h, WS910-19, and WS910-29.

NOTE: For detailed Placement instructors refer to the control panel

reference manual

no location the coverage area by walking across the far end of the cov

was a new, in both directions, the and LOP light seek their way.

range pattern in both directions. The 100 LCD lights each time your version is detected, followed by a 'type' LED signal strength inflation

Mountain the devices

Mounting the device

1. Mark and drill two holes in the mounting surface. If you install

tarpur protection on the detector mark and drill one bele for the

tarry, protection and are able for one of the other available play

The following table provides the information in the United States:

1. Fasting the bracket to the mounting surface with the two screws.

2. Align the bracket tube with the detector slots and points the detector

clock near. Verify, that, it is exactly attached

1. Fasten the detector to the bracket with the screw.

Figure 4. Fastening the

Figure 5. Attacking the detector

A. Tannser protection
(3) 本报告书和本报告书的名称
B. Bcndel, Sclw, Sl015
C Isolation script

Figure 6. Fasting the detector broke that

1. 1798-

17.4825

to, following table outlines the detection distance in relation to the

mounting height.

2017年1月1日

。

•

the

LED Indicutions		Event
Red LED	blinks	Stabilization (twarm-up 90 seconds)
Red LED on 0.2 seconds Tamper open/close
Redwdelting on 2 seconds Intruder alarm

Temperature display

box instructions on displaying the temperature of zones on the co

procel, as measured by the PGS872 refer to the postal installation.

P-ENIC

Specifications

Gidueral

Detector Type

fear projectile season, operating in a dual separated configuration

Optical

Lens data

Fresnel type lens.

Number of teams

Max. coverage

20 m/360° at the maximum installation height of 6 m (19.7 ft)

Figure 7. Beam distribution at 2.7 m (8.9 fl)

Figure 8. Beam distribution at 6 m (19.7 R)

Electrical

Power supply

obese

Johnson

Controls

Internal. 3V Liobium battery type CR123A. For IT-ACT, installation, energy and, if not installed and used in accordance with teleocational-user license agreement is licensed to You under the terms AGREEMENT SHALL DE LIMITED TO THE GREATER OF THE AM USE only Panasonic or GP batteries. EN50131-6 type C power tolerance cause harmful interference to radio and television receptioence agreement. Battery life (typical use) However, there is no guarantee that interference will not occur in Deportailing, copying, downloading, accessing, accessing or otherwise distinctive CANADIAN DOLLARS CAD\$5000, RECAUSE SOME
Minimum year: 3 years for typical use-security mode (not verification). If this device does cause such interference, which can believe SOFTWARE PRODUCT. You agree unconditionally to be bound. PRODUCATIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION U.S. 2 years in presence mode with timer set to 15 min (the version of the device off and on, the use is encouraged to eliminate the time-ELIA, even if this ELIA is deemed to be a model. FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE Practice by one or more of the following measures: previous arrangement or contract. If you do not agree to the terms applying THIS LIMITATION MAY NOT APPLY TO YOU!
ly 1.1.1. Low battery threshold
2.5 V
NOTE: Inability to connect with wireless network, or wireless
quality no higher than 20% may significantly reduce the expensive life
Battery power test
Performed immediately upon battery insertion and periodically
every several hours.
The power supply is type C in accordance with EN 50131-6
Inclination - Clustic Current consumption
30 μA average quiescent, maximum 150 mA (during transmi
Functional
True Motion Event Verification
2 remote selections at plane Alarm Periods
2 seconds
Wireless
Frequency
Europe and rest of world: 423-424 MHz, 868-869 MHz US
919 MIIy
NOTE: Only devices in frequency band 915 MHz are UL/UL
Communication Protocol
PowerG
Supervision
Signaling at 256 second intervals
Tamper alert
Reported when a tamper event occurs and in any subsequent
until the tamper switch is restored. Mounting
Mounting Weight
Height 2 m to n m 16.6 ft to 19.7 ft
Installation options
Ceiling surface
Environmental
RF Immunity
20 V/m up to 1000 MHz, 10 V/m up to 2700 MHz
Operating Temperatures
-10 °C. (a) 35 °C. (14 - 1 b) (31 - 4).
NOTE: UL verified operation range 0°C to 49°C only.
Storage Temperatures
-20 ℃ to 60 ℃ 14 F o 140 F
Humidity
Average relative humidity of up to approximately 75% non-con
densing. For 30 days per year the relative humidity may var
85% and 95% non-condensing
For UL installations: 5% to 95% with no condensation
Physical
Size (diameter)
15 cm 15.9
Weight (with battery)
100 p [3.88 oz]
Color White
[Unreadable]
This device can be used with DSC panels and receivers that
PowerG technology
NOTE: Only devices operating in hand 912-919MHz are UI
led.
Only model PS9572 operating in the frequency band 912-915MHz
LL/LLC listed. The PG9872 has been listed by UL for commercial
identical burglary applications and by ULC for residential burglary op
ations in accordance with the requirements in the Standards UL 63
1.13 - Smith Far Intrusion Detection Units. For UL-FLC, installments are this day
For CL/CLC instructions use this device only in conjunction with suitable DSC wireless privacy U5M2HOST9 U521CDRFID09 U5JICN
9. PG9920, WS900-19, and WS900-29. After installation verify the
functionality in conjunction with the compatible receiver used.
WARNING/Changes or modifications to this unit not expressly approv
the party responsible for compliance could void the user's authority
ate the equipment.
This device has been tested and found to comply with the limits
B digital device, pursuant to Part 15 of the FCC. Rules. These is designed to provide observable protection against harmful interferances.
designed to provide reasonable protection against natural interference; identical installations. This equipment generates uses and can radiate
tijones: energy and, if not installed and used in accordance with
Emergency cause harmful interference to radio and television recept
However, there is no guarantee that interference will not occur in
the device. It this device does cause such interference, which can by particular, the device off and on, the area is encouraged to elin
are verified
- Re-orient or re-locate the receiving anlem
Increase the distance between the device and the receiver.
- Connect the device to an outlet on a circuit different from its
- Puck power to the receiver. - Consult the dealer or an decentralized radio-TV technician.
edc bap: F51SPG9872
(16) SED) Statement This equipment complies with PCI and ISIO Caméa RF radiation
This equipment compares with PCC and ISRD, calculated to be obtained limits, set forth for an uncontrolled environment.
This device complies with FCC Rules Part 15 and with ISED Ca
except RSS standards). Operation is subject to the following two
drone: (1) This device may not cause harmful interference, and (2)
device must accept any interference that may be received or that undicised operation.
1.e present appareil 2st conforme aux CNR d'ISED Canada applizahl
acoureuls radio exempts de licence. L'exploitation est autorisée aux
ditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
salinar de l'oppratil dait auxiplar toji. fronillaga nathelaxtrigae, subi, la brochura eut avoontible, 27. superovale, la forstavareant
IC: 160A-PG39872
A: 912-
Europe: CEEN (EN5011)-2-2 GRADE 2, CLAS5 II, EN50
C. list: type (C) list: PG8872: 868 MHz PG4872: 433 MHz
1. 本报告期公司实现的净利润为2023年1-6月，归属于母公司股东的净利润为2023年1-6月。
According to EN 50131-1, this equipment can be applied in install
by Applica Test and Certificates AS in accordance with E.N 5013-5017.5.1, EN: 5017.6, EN: 5017.9, EN: 5017.5, UK: https://p.887
to be, let use in systems installed to transform to PD6662 at Grade
10.5243, 10.5244, class 2 RS8243.
Hereby, Tyco Safety Products Canada Ltd. declares that the radio
type is in compliance with Directive 2014-23.5EU. The full text of the ELL declaration of conformity is available at
the text later of the 2.0 occurrence of conversion, it is important at: internet address:
PGi4872 http://sl
PG8572 http://dsc.com/pd1710004
Frequency band Maximum power
868.0 MHz - 868.6 MHz 10 mW
868.7 MHz 869.2 MHz 10 mW
European single point of contact: Tyco Safety Products, Voltaweg 2
XK Felt, Netherlands
Digital Security Controls (DSC) warrants that for a period of twelve
from the date of purchase, the product shall be free of defects
workmanship under normal use and that in placement of any break
warranty, DSC staff, at its option, repair or replace the defects upon leave of the equipment to its factory. This warranty applies
defects in ports and workmanship and not to damage incurred in
handling, or damage due to causes beyond the control of DSC s.
ning, excessive voltage, mechanical shock, waterdamage, or damage
not of abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original power and
The foregoing warranty shall only only to the original buyer, and shall be in lieu of any and all other warranties, whether stressed
and of all other obligations at liabilities on the part of DSC.
contains the entire warranty. Digital Security Controls neither assume
responsibility for, nor authorizes any other person purporting to act
himself to modify or to change this warranty, nor to assume for
warranty or facility concerning this product. In no event seal DSI for our client or implied an environmental characteristics report of activity
- T.C. Costs: Loss of time or any other losses incurred by the buyer connection
purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system
completely tested on a regular basis. However, despite frequent testi
and over but not limited to, circumlampening or electrical disrupts
IMPORTANT READ CAREFULLY: DSC Software purchased with
without Products and Components is copyrighted and is purchased
Following license:
RPM: Full-Use License Agreement ("EIBA") is a legal agreement.
(1) company, individual in security with acquisition the Software and Hardware and Digital Security Controls, a division of Two Safety
Canada Ltd. ("DSC"), the manufacturer of the integrated security
the developer of the software and any related products or compuni
PHARDWARE ^TM which You acquired If the DSC software product
[POSTSPEAVARE PRODUCT" or "SOFTWARE"] is intended to be acc
by HARDWARE, and is NOT accomplished by new HARDWARE,
PRODICT includes computer software, and may include associated
Printed materials and "online" or electronic documentation. Any self
provided along with the SOFTWARE PRODUCT that is associated
barated-and-user license agreement is licensed to You under the terms A01
ob license agreement.
dyspmbalimg, copying, downloading, storing, accessing or otherwise using
eese viewed WARE PRODUCTS. For agree, incontinently to be sold for in terms of the other ELLA, even if this ELLA is desired to be a modification
previous arrangement of contract, if You do not agree to the terms ARE
EULA, DSC is unwilling to license the SOFTWARE PRODUCT to Idpu.
You have no right to use it.
The SOFTWARE PRODUCT is protected by copyright laws and intermedia
copyright treaties, as well as other intellectual property laws and treaties.
SOFTWAREPRODUCT is licensed, not sold. 1. GRANT OF LICENSE. This EULA grants You the following right
(1) Software Installation and Use For each license You acquire, YQTI
imposonly one copy of the SOFTWARE PRODUCT installed.
(b) Stovery Network Use - The SOFTWAREPRODUCT may not be in mill
niss experience, displayed, run, scaled or used concurrence on or from different commuters, including a workstation terminal or other digital electronic MD
(“Bevies”) In other words, if You have several workstations. You watch
the software a license for each workstation where the SOFTWARE willPRO
(e) Backup Copy - You may make backup copies of the SOFTWARE.
es'QHJUCCI, but You may only have one copy per license inserted in C. green time. You now use the back-up copy solely for a buy-in purchase
exempt past expressly provided in this EULA. You may not otherwise Cnt
epplies at the SOFTWARE PRODUCT, including the printed materials FAC
panying the SOFTWARE CLA
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS TO
(1) Limitations on Reverse Engineering, Decomposition and Disassembly phase. You may not reverse agent, document or disassemble the SOFTWARE
PRODUCT, except and only to the extent that such activity is exploidy
mitted by applicable law notwithstanding this limitation. You may not Thus
any changes or modifications to the Software, without the written pertaining
of an officer of DSC. You may not remove any proprietary noticesplien
1. QEPHE: E.N. (been the Software Product. You shall institute reasonable measurement of _0 compliance with the words and conditions, with this. FLLA – this
21b1 ^5 Specification of Components - The SOFTWARE PRODUCT is licenager
single perceived. Its component parts may not be supported for use of
than one HARDWARE unit. 003
(1) Single INTEGRATED PRODUCT. It is acquired in: SOFTWARE, hardware, then the SOFTWARE PRODUCT is licensed with the
OTHERWARE is a single integrated product. In this case, the SOFTWARE
PRODLC1 may only be used with the HARDWARE as set forth in
(1) Foset: New York, 2015; 2016; and the WOHS MARKETING
(ii) Kenal - You may not tell, call, or call the MP/MPERPROD.
10) Software Product Transfer You may transfer all of Your rights
EULA only as part of a permanent sale or transfer of the HARDWARE
provided You retain no copies, You transfer all of the SOFTWARE lipers
PRODUCT (including all component parts, the matrix and printed materials) and (invariants and this BHA) were awarded for recipient orders to be
fully-upgrades and this ELLA, and provided the recipient agrees to page of this ELLA. If the SOFTWARE PRODUCT is on upgrade, any transfer
also include all prior versions of the SOFTWARE PRODUCT.
of f months Termination - Without prejudice to any other rights, DSC may termi
a. This model's and You fail to comply with the terms and conditions of it
In of such event. You must destroy all copies of the SOFTWARE PRODU
eilbentu, th. its component parts. Pra Tradewarks. This fell A does not agree. You any rights in connec
with ane trademarks or service marks of DSC or its suppliers.
COPYRIGHT - All title and intellectual property rights in and to th
- SOFTWAREPRODUCT (including but not limited to any images, photo)

• Photo_image and photo, incremented into the SOFTWARE PRODUCT, the two
  graphine, and text incorporated into the SOFTWARE PRODUCT, the following printed materials and any series of the SOFTWARE PRODUCT
  ownest by DSC of its supplies. You may not copy the printed material
  accompanying the SOFTWARE PRODUCT. All title and intellectual project
  rights in' and to the context which may be accessed through use of.
  SOFTWAREPRODUCT are the property of the respective context owner a
  in any other. This EUA greats You no rights to use such content. All
  ne not expactly granted under this HILA are reserved by DSC and its.
  EXPORT RESTRICTIONS - You agree that You will not export or
  USE SOFTWARE PRODUCT to any country, person, or entity subject to
  plan export restrictions. 5 ^th CHOICE OF LAW. This Software License, Appointment is unamortified
  Law and the Provinces of Ontario, Canada.
  reg. ARBITRATION - All disputes arising in connection with this Agreement
  shall be determined by final and binding arbitration in accordance with
  Arbitration Act, and the parties agree to be bound by the arbitrators of the issue of arbitration shall be Toronto Canada and the language of
  The place of artificial skin is: Thalm, Varnite, and the language for arbitration. shall be English.
  WARRANTY - DIS PROVIDES THE SOFTWARE "AS IS" W
  WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE W
  the MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE
  SOFTWAREWILL BE UNINTERRUPTED OR ERROR-FREE
  unbambi-HANGES IN OPERATING ENVIRONMENT - DSC shall not be r
  Year may problems caused by changes in the operating transactions of SMARTWARE or live problems in the interaction at the SOFTWARE.
  PRODUCE with non-DSC-SOFTWARE at HARDWARE PRODUCTS.
  LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION
  RISK, - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES
  CAD/TRINS ACT INATED IN THIS LICENSE AGREEMENT, TAX A ENHURE LIABILITY UNDER ANY PROVISION OF THIS LICENSE

COMPATIBLE RECEIVERS

III/II/LC Notes

ECC COMPLIANCE STATEMENT

Innovation Science and Economic Development Canada

(USED) Statement

lems up to and including Security Grade 2,

Simplified EU

Simplified ED declaration of conformity

Limited Warranty

SOFTWARE PRODUCT LICENSE

7 LIMITED WARRANTY

2.4A(10) = 13.4B(13) - 1 - 6,4D(5) - 4A) = 8.4E(10) A - 63 = 110 - 110 - 110 - 110

Circular pattern composed of concentric rings with evenly spaced small dots, no text or symbols present

Communication Sans III

frequency

Europe et Reste dlt Imode: +3.1- +3.4 MHz, 868-869 MHz F

912-919 MH2

m = 311

le ais

1

[Unreadable]

1

bien

4

1

1

1

[Non-Text]

[Figure 1]

1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 99.

1

7

[Table_Title]

1

1. 2017年1月1日

1

1

[1]

[1]

Source: 4. Relocation, ed

figura 3. Sufecion del

2.0.6 metros (b.6 - 19.7 pies)

Inmunidad a RF 20 V/m hosts 1000 MHz 10 V/m hosts 2700 MHz

Fino de 2016, 1980 in the Europe. (Year: Sydney, France), Vomaway, GIDL, XX, light, Hylands

cna

FOR PG9872/PG8872/PG4872 Visão geral

Introdução

A. PC×S72

tupo incorrete. Descarle as baterias usadas de acordo com as

Circular diagram with concentric rings and radial lines, no text or symbols present

15 cm Bass (cwt, hotAPI)

1. n (2.85, 26)

Cor

Branca