TXP2.6500D - Receiver Soundstream - Free user manual and instructions

USER MANUAL TXP2.6500D Soundstream

TXP2.6500D TXP4.3500D TXP1.3500D TXP1.6000D TXP1.12000D TXP1.18000D

Compact Size High Power Amplifier

PLEASE READ THIS MANUAL BEFORE INSTARAGE AND USING AMPLIFIER

Congratulations on your Purchase

Your new high fidelity bridgebriestered amplifier is designed to deliver maximum enjoyment and years of trouble free service. The quality of the installation may affect the performance and the reliability of your products

Features

Class "D" High Efficiency Mono Block Car Amplifier
● Bridgeable & TRI-Mode Operation.
●Continuity Variable 1200/Octave High Pass & 1200/Octave Low Pass Crossover ●Exterior Variable Exposure for Pass Phase Control
- Enhanced Bana Brasil +1318 (R\$50H)
■Silver Plated RGA, Power & Speaker Terminal
●Soft Start & Mating
●Overload Thermal
●Power & Protection Monitor. ●Nass Land Rentals Control 18, 4951

Precautions: Read First!

●The amplifier needs to be installed by an authorised installer

Negative battery terminal must be disconnected before any electrical connections are made. So sure choose a location that provides substantial ventilation for the amplifier. The most preferred locations would be in you can't track, under the front seats or on the back wall of a truck.

- The location chose should provide at least 2° of clearance above the amplifier for adequate

- If the equal or is to be mounted vertically be sure that it is in a place where adequate or

and now along the length of its health controls for recovery.

●NEVER mount the amplifier up side down, this will cause the heat to

amplifier causing thermal shutdown or possible permanent damage

●NEVER mount the amplifier in a location that is subject to direct sunlight or exposed to

Moisture

●Be sure to mount the amplifier to a strong, acid surface which will not give way under the

stress of a sudden soap or accident

●Make sure that the mounting screws will not generate the gas tank. Brake and fuel lines

being to other critical parts of your cat when initiated

■ Ensure that quality rating is used to enhance the safety and performance of your

(2) 求心病

● Warranty must be void if proper installation technique and ceiling is not used.

7

SPECIFICATION

TXP1.12000D

1.300w x 1@4-phm Stereo

2.300m x 7 @ 2-ohm Stereo

4.300w x 1 @ 1-ohm Stereo

12.000m MAX Power

THD: +0.3%

Input Sensitivity: 200My-6V

HRS:15.80Hz

1.26:50-30KH

LFP: 80-20kHz Rass Report: 0-12dB 50Hz Rass Report

Bass Boost. 0-120B 30HZ Bass Book

Frequency Response: 20-20kHz

S/N: 105dB

Working Voltage: 99-10V DC

Distortion Clip Lights

With Remote Controller

Size:8.25" w x 2.75" h x 7.25"

TXP1.18000D

1.800w x 1 @ 4-ohm Stereo

3,600w x 1 @ 2-ohm Stereo

7.000w x 1 @ 1-ohm Stereo

18.000w MAX Power

THD: <0.3%

Input Servit

Input Sensitivity, 2.0dB-04

HPF:13-20H2

LPF:80-20KHz

Bass Boost: 0-12dB 50Hz Bass Boost

Frequency Response: 20-20KHz

S/N: 105dB

Working Voltage: 9V-16V DC

Distortion Clip Lights

With Remote Control

Size: 8.75" w×2.75" h×10.5"

SPECIFICATION

TXP2.65000

400w×2@4-ohm Stereo

700w x 2 @ 2-ohm Stereo

1.250w x 2 @ 1 ohm Stereo

2.500=×1=2-ohm Bridged

6,500—MAX Power

6,300M MAX

THD: <0.3%

Input Sensitivity: 200Mv-6V

HPF:15-1KHz

LPF:50-10KH

Bass Boost: 0-12dB 5GHz Bass Boost

SUN: 10549

310.1056

Working voltage: 9V-16V DC

Distortion Clip Lights

With Remote Controller

Size: 8.25" w×2.75" b×5.75"

TXP4.3500D

140w x 4 @ 4-ohm Stereo

23Swx4@2-ohm Stereo

375w x 4 @ 1 ohm Stereo

700m x 2 @ 2-ohm Bridged

2,500+ MAX Power

3,500 MARS TUR: 0.24

THD: <0.3%

Input Sensitivity: 200Mw-5V

HPF:15-6kHz 12dB

LPF: 50-6KHz 12dB

Bass Boost: 0-12dB

S/N: 10549

SIN: 10,000

Working voltage: 2V-1BV DC

Distortion Clip Lights

Size: 8.25" w×2.75" h×7.25"

(1) 本说明仅供参考。

TXP1.35000

450w x 1 @ 4-ohm Stereo

800=×1=2-ohm Stereo

1.250w x 1 @ Lohm Stereo

2,500—MAX Power

3,500M MAX Power

THD: <0.3%

Input Sensitivity: 200Mv-6V

HPF:15-1KHz

LPF:50-10KH

Bass Report: 0-12dB 50Hz Bass Report

BASY BOOST: 6-12/05 30-12 DAYS BOOST

Frequency Response: 20-20kHz

S/N: 105dB

Working Voltage: 9V-16V DC

Distortion Clip Lights

With Remote Controls

Size: 8.25" w×2.75" h×4.25"

TXP1.6000C

700w x 1 @ 4-ohm Stereo

1.200w x 1 in Zohn Stegen

2.350w x 1 @ 1-ohm Stereo

1. ОПОУ МАХ РОЧИЯ

6,000 MRC

THD: <0.3%

Input Sensitivity: 200Mv-5V

HPF:15-BCH

LPF:80-20KH;

Bass Boost: 0-12dB 50Hz Bass Boost

Frequency Response: 20-20kHz

5/N:105dB

Working Voltage: 9V-16V DC

Distortion Clip Lights

With Remote Control

Size: 8.25" w x 2.75" h x 5.75"

1

2

INSTALLATION & CONNECTIONS

MOUNTING

1. After reading precaution, decide where you are going to install the unit. Also, see Fig. 1.

2 Once the location has been determined, place the amplifier into position. Using a left to

pen of pencil mark the four holes to be drilled for mounting. NEVER use the ampillar as

a template for drilling. It is very easy to damage the amplifier surface in this manner.

1. Remove amplifier. Drill four 3.5 min holes into mounting surface, if you want to mount

the amplifier to MOF or wood panel, drill four 3.0 mm diameter holes into mounting surface.

1. If possible, test the system to ensure it is operating correctly before final meeting of

the angiter

1. Mount the smaller uses the supplied 4-well lapex score.

INPUT CONNECTIONS

This amplifier will accept low level inputs only. Low level in the same as low level. The low

level signal is control through RGA cables. It is preferred to use low level inputs to the

another if the head unit is equipped with the low level output. If not, you can use a "high

"to low converter" available through your local car audio shop.

Correct the low level/line level RCA cable from the head and, or signal processor, to the

the level input on the amplifier. See Fig.2 system wiring diagrams

POWER CONNECTIONS

It is important to have good quality power and ground connections. Remember: to complete

an electrical circuit, the ground correction is just as important as the positive power.

connection. Before any power connections are made, disconnect the ground cable at the

Country

When the power supply lead, memory backup lead of ground lead are extended use a time ^1

(AWG5) or larger automotive grade cable which will withstand

Green open, and occurring with a loss of about 100%

GND=Connect the proper gauge ground wire to the amplifier 'GND' terminal. Locate the

position on the chessay of the car to which the amplifier is to be grounded. The surface must

[9] You from any part of the. This can be accomplished with a small grinding bit, sand

paper of Ave Street. NOTE: Do not ground the arqpise to the "trice" of the car. The hands in most cars and trucks is not up-and, to the chagie (body), Use Holder or a plume day to

respect the ground wire. Fre-drill the prepared chassis to bolt the grounding terminal with

nut, bolt and lick washers. Incurate metal and connector with paint or silicon to prevent

natal and oxidation. Silicon also works great to prevent nuts and beta from working loose in

a furnish environment of an automobile. Open completion of the ground connection, probably as appropriate and confirm that it is a gold environment. To prevent silver prices, this

wire or circuit and conduction, it is a solid conduction. To prevent angle noise, it is recommended to ground the hand wall and other autics elongating in the semi-lacally

We believe that our future growth is the most significant factor in the future situation.

REM = Connect the remote wire (power antennas output) from the head unit to the remote

from an wire of the amplifier. If the head unit is not equipped with a remote antenna output,

As to a web of that is categorized by the necessary position of this say. It is important to have the email because off the code or away. If the email has been on, the email will now

The ship

12) Helvemil: The new version was in the world for "The" improvement. Results to

12V=Connector proper gauge power, which is the amplifier of reference. Net wire to

3

TROUBLE SHOOTING GUIDE

This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult the listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e.g. headlights, windows, etc.) still function correctly.

SYM/FOM	PROBABLE SOURCE	SOLUTION
RoAudio	Low or N.C. RemoteTurn-off-connectedBlown FusePower lines not connected	Check remove turn-off voltage atamp and head-will
		Replace with new feed blow fuseCheck boot uptake power pointsCheck ground and battery connections
	Blown or on speakerconnected	Use VDM or DNA to measure speakerstillindependent check speaker wiringconnections
Distorted Audio	Input sensitivity not setpropertyor damaged speaker centers	See adjustment procedure and checkeach step;
		Interrupt each speaker for damageand repair or reaction suspectedcomponent
	Low turn-on voltage	Refer to head-unit owner's manual
Audio Level Low	Multi circuit on headunit on an.	Check electrical system for lowvoltage;Check ground connection
Audio Lamps	Speakers wired with wrongpriority causingconceiling of basesfrequency.	Check yearly of remote fromamplifiers to earb speaker Assisted ifthe system designCheck battery voltage at amplifierduring operation
External FuseSlowing	Interconnecting at shortcircuit	Refer to electrical installation andcheck power connection step
Writing noiseon audio withenging running	Amplifier taking upadditional noise	install an in-line noise filter on thehead unit's power wire. Checkall signal matching switches onregulator for proper operation. Checkall signals, battery voltage, andRCA cables.
Teaching noise onaud to withenging running	Amplifier taking upadditional noise	Check RCA audio cable install anin-line noise filter on thehead unit's power wire. Check spark propylene.

8

ADJUSTMENTS

Set to the 'K.P.F' position when the amplifier is used to drive a wireless-range system. The frequencies below the crossover point will be attenuated at 12dB/octane. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 4kHz to 1.2 kHz as the crossover point.

1. Set to the "L.P.F" position when the amplifier is used to drive a subcarrier. The frequencies above the crossover point will be attenuated at 12dBectave. Parents adjustment of the crossover frequency, by rotating the knot to select any frequency between 50Hz to 250Hz as the crossover point.

3.5a1 to the "OFF" position when the amplifier will be used for driving full-range speakers. The full frequency band width (20Hz-20KHz) will be output to the speakers without high or low frequency attenuation.

1. Level adjustment The sensitivity adjustment is to allow the amplifier to work with many different brands of head units. In loose input signal to vary between 350 millivolts to 5 volt from the head unit or other signal processor. Start by setting the sensitivity adjustment to be "the 1/2" (200 volts) using a cassette or compact disc that you are taken with "turn on the head unit." The 314 volume is set up to 100 volts, and the "MAX" (200 mV) voltage using a flat head screw drive. Stop turning on the onset of distortion and turn back just a night. The 314 volume setting is now the maximum I volume for the head unit. The goal is to keep the level control to the forward setting yet still have enough signal to drive the amplifier. This is done to prevent over driving the impulse and to keep the power of the current operating system. This important no ever drive speakers will count of circums in this well as cause permanent damage to speaker. Also, if the amplifier itself is over driver it could be damaged.

2. The "BASS" function can be selected to increase low frequency response output, or decrease frequency response output. The "BASS" function will be working properly. OFF or "L.P.F" position.

• The BASS is adjustable from 0–12 dB boost at 50Hz.

7

1 CHANNEL MONO BLOCK CLASS D AMPLIFIER CONNECTION

Install the fuse holder that is less than 2.5 meters from the battery. Remember the fuse is to protect the safety of the air in case of a short. Connect fuse holder to battery but do not install fuse at this time.

This amplifier can operate in one, two or three channel mode. The minimum impedance for

single channel (bridged mono) operation is 4 or 6 otherwise. Tri channel power is referred to

stereo and more at the same time. Minimum impedance remains the same to three channels

(see the following system as long as proper passive transmitters are used. Correlations and left speaker wire to corresponding spectral output terminals of the amplifier. He sure to

have the positive wine from the speaker connected to the positive speaker terminal of the

amplifier and the negative wire from the speaker must connect with the negative speaker

terminal of the amplifier. Reversing any of these connections will result in the speaker con

moreing out of phase which causes blood cannulation. See Fig.3 Speaker Output Connection

MONO CHANNEL SPEAKER WIRING DIAGRAM

TXP1.3500D/TXP1.6000D/TXP1.12000D/TXP1.18000D

TXP1.35000/TXP1.60000/TXP1.120000/TXP1.180000

4

2CHANNEL AMPLIFIER WIRING

TXR2 6500D

FRONT

TXP2.6500D

REAR

5

4CHANNEL AMPLIFIER WIRING

TXP4:3500D

FRONT

TXP4.3500D

REAR

E