Funk KWH-150 - Headphones Klip Xtreme - Free user manual and instructions

Product Type	Over-ear wireless headphones
Model	KWH-150
Brand	Klip Xtreme
Driver Unit	Φ40mm
Frequency Response	20Hz - 20kHz
Impedance	32Ω ±15%
Sensitivity	105±3dB/mW (S.P.L at 1kHz)
Microphone	Built-in omnidirectional (100Hz-18kHz)
Connectivity	Bluetooth® V5.0, 3.5mm auxiliary input
Wireless Range	Up to 33 feet (10 meters)
Battery Type	Built-in rechargeable lithium-ion (3.7VDC, 500mAh)
Charging Time	Approximately 3.5 hours
Playback Time	Up to 18 hours (at 50% volume)
Standby Time	Up to 30 hours
Dimensions (LxWxH)	6.8 x 2.9 x 7.2 inches
Weight	12.6 ounces (357 grams)
Foldable Design	Yes
Material	ABS plastic
Controls	On-ear buttons for power, volume, track, and calls
LED Indicator	Power, charging, Bluetooth status
Cable Length (Aux)	Approximately 3.9 feet (1.2 meters)
Warranty	1 year
Cleaning	Use a soft, dry cloth; avoid solvents and alcohol
Safety	Do not expose to extreme heat, moisture, or disassemble

Frequently Asked Questions - Funk KWH-150 Klip Xtreme

How do I pair the headphones with my phone?

Turn on the headphones. The LED will blink red and blue, indicating pairing mode. On your phone, enable Bluetooth and select 'KWH-150' from the list. If prompted, enter passkey 0000. A tone confirms successful pairing.

Why are my headphones not charging?

Ensure the micro-USB cable is securely connected to both the headphones and a power source. Verify the power source is working. If using a different cable, check it is functional. The LED glows red during charging and turns off when fully charged.

How long does the battery last?

Playback time is up to 18 hours at 50% volume, and up to 13 hours at full volume. Standby time is up to 30 hours. Charging takes about 3.5 hours.

Can I use the headphones while charging?

Yes, you can use the headphones in wired mode (aux-in) while charging. However, Bluetooth mode may be disabled during charging. It's recommended to charge fully before wireless use.

How do I switch to aux mode?

With the headphones on, insert the 3.5mm cable into the headphones and your audio source. The LED will turn off and the headphones will automatically switch to aux mode. Note that volume controls on the headphones will not work in aux mode; adjust volume from the source.

Why is there no sound coming from the headphones?

Check that both the headphones and your Bluetooth device are powered on and paired. Ensure music is playing and volume is up. If using aux, confirm the cable is fully inserted. Also verify that the Bluetooth device is not connected to another audio output.

How do I answer or end a call?

Briefly press the multifunction (play/pause) button to answer an incoming call. Press again to end the call. To reject a call, press and hold the multifunction button for about 2 seconds.

What should I do if there is distortion or interference?

Keep the headphones and your Bluetooth device within the recommended range (up to 33 feet). Move away from other 2.4GHz devices like Wi-Fi routers. Also ensure there are no physical obstacles between the devices.

Can I use the headphones with a computer?

Yes, via Bluetooth if your computer has Bluetooth capability, or using the included 3.5mm aux cable for wired connection.

How do I clean my headphones?

Use a soft, dry cloth to wipe the exterior. Do not use benzene, solvents, or alcohol. Avoid getting moisture into the ports or ear cups. Store in a cool, dry place away from direct sunlight.

USER MANUAL Funk KWH-150 Klip Xtreme

Close-up of a modern black and silver outdoor headphones with a green background (no text or symbols visible)

KWH-150

I. Introduction

Thank you for purchasing the KWH-150 stereo headphones with Bluetooth® wireless technology. We encourage you to read this quick installation guide thoroughly to get the most of this innovative wireless device.

Main features

• Bluetooth® V5.0 platform, for greater wireless range, and a reliable wireless connection
• Long-lasting 18-hours battery life, with 30 hours of standby time
• Includes enhanced technology to deliver better sound quality
• Delivers flexibility with its Aux-in function to connect the headphones to a 3.5mm cable and save battery
• Seamless and hands-free experience when answering or making calls
• On-board controls for power, music, and phone call management
• Foldable design for limitless mobility and easy to fit in tight spaces
• Cushioned leatherette headband that conveniently extends for maximum comfort
  • Lightweight design with comfortable ear cups
• Fashionable and modern appearance to enhance your style

Package content

• Wireless headphones
• Micro-USB charging cable
• Aux in (3.5mm) audio cable
• Quick installation guide

II. Product components

I. Adjustable headband
2. Power On/Off switch
3. ▶▶+ : Volume+/next song
4. - ←: Volume-/previous song
5. Micro USB charging port
6. ▶ : Play/pause/multifunction button
7. LED indicator: For power/battery charging/and Bluetooth® status
8. Cushioned ear pads
9. 3.5mm auxiliary input port
10. Microphone

Button	Function
Power on/off switch [ON OFF]	Slide the switch to the left to turn the device on.Slide the switch to the right to turn the device off.
Volume up/next track button ➤ ➤	Press this button briefly to increase the audio level of the headphones.Press and hold this button to play next track.
Volume down/ previous track button — ←	Press this button briefly to decrease the audio level of the headphones.Press and hold this button to play the previous track.

Button	Function
Play/pause/answer-hang up call/redial/reject call - multifunction button ▶||	Briefly press this button to play and pause media.Briefly press this button once to answer an incoming call (music will be paused).Briefly press this button once to end a call (music will resume).Double click this button to rodial the last number called. (on supported devices).Press and hold this button for about 2 seconds to reject an incoming call.
Micro USB charging port	Insert the micro-USB cable here to recharge the battery.

LED indicator light status

Charging status	LED indicator will be steady red while charging.LED indicator light will turn off when fully charged.
Power on status	LED indicator turns on in Blue.
Power off status	LED indicator turns off.
Pairing status	Blue and red LED indicator lights up rapidly flashing(alternating).
Standby status	LED indicator light turns on Blue.
Connected status	LED indicator light turns on solid Blue.
Using headset in Aux/BT Mode	Bluetooth® mode- blue LED indicator light blinks slowly.AUX-in mode, the LED indicator automatically turns off.

III. Basic operation

Charging your headphones

• Plug one end of the supplied micro-USB cable to your headphones micro-USB port and the other end into the USB port of your computer or to a 5VDC 500mAh to a USB adapter to fully charge the battery.*
• The headphones' battery should be initially charged for at least 5 hours. Thereafter, the battery will take about 3.5 hours to recharge.
• Make sure that the headphones are fully charged before using them for the first time.
• When battery is low a voice prompt will be heard to indicate battery status.

*Do not use a USB fast charging or PD adapters with an output power greater than 5VDC or you will damage your headphones and void the warranty.

IV. Auxiliary wired connection

• With the headset ON you can insert the 3.5mm cable to switch to Aux in mode. Plug one end of the supplied 3.5mm cable to your headphones and the other end to the 3.5mm auxiliary port in your input source.
• The LED indicator on the headset will turn off and the headset will automatically switch to aux in mode.
• Set the desired volume on the input source. The volume controls on the
  headphone will not operate when they are connected to an external wired audio source.

Note: Once you remove the cable you cannot return to Bluetooth ^ mode, you must turn the unit on again to enter Bluetooth ^ mode.

V. Advanced operation

Pairing the headset with your mobile phone

1. Tum on the device, the LED light will start in Bluetooth® mode automatically, blinking red and blue indicating that it is ready for pairing mode.
2. Next, set your Bluetooth ^® mobile device to "discover" the wireless headphones.

3. Place both devices not more than one meter away from each other.

4. On your mobile phone, tap the newly discovered audio device KWH-150 being displayed in the Bluetooth® list.

5. If you have a lower Bluetooth ^® version, you may be prompted to enter the passkey 0000 (1 zeros).
6. If pairing is successful, an audible tone will be heard. If after 60 seconds the pairing process fails, please turn off the headset and repeat steps 1 through 5 described above.
7. The headset will enter into standby mode and will eventually turn off automatically after five minutes if there is no Bluetooth ^® device available for pairing.

Note: The headset will automatically pair to the last known connected device in 3 seconds after headset is powered on.

VI. Using the wireless headset

a. Answering and ending a call using your mobile phone

1. When there is an incoming call, an alert tone will be heard through your headphones. Briefly press the play/pause, multifunction button to pick it up. You may also press the answer button on your smartphone to take the call. (music will be paused)

2. To end a call, simply press the multifunction button once again. Likewise, you may also finish the call directly using the end key on your mobile. (music will resume automatically)

3. To reject an incoming call, press the multifunction button for about 2 seconds.

4. If you want to redial the last number dialed, double click this button to redial the last number called. (on supported devices).

b. Music playback

1. Briefly press the play/pause, multifunction button ▶|| to reproduce and stop audio playback.
2. Press and hold the ▶+ and -◀◀ buttons for 2 seconds to go to the next or previous track.
3. Briefly press the ▶▶+ and —◀◀ buttons to increase or decrease the volume on the headphones.
4. When listening to music using your smartphone, playback will pause to allow the call to go through.
5. As soon as you hang up, music playback will resume automatically.

VII. Troubleshooting

a. The headphones are not turning on.

- Charge the headphones. If they don't turn on even after charging, contact customer service for help.

b. The headphones are not charging.

- Check if the supplied USB charging cable has been properly connected to the headphones and the power source.

- Verify if the power source is on and properly connected.

- If using a USB charging cable different from the one supplied, make sure that it is properly connected and functioning.

c. The headphones are not pairing.

- Check if the Bluetooth® device is powered on.

- Verify if the Bluetooth® mode is enabled on the device.

- Check if both devices are within 1 meter from each other.

- Verify if the Bluetooth® device is compatible with the headphones.

d. Music will not play through the headphones.

- Check if the headphones and the Bluetooth® device are powered on.

- Verify if there is music playing on your Bluetooth ^® device.

- Check the volume level on your Bluetooth® device.

e. There is distortion, lag or interference in the connection.

- Check if there is a 2.4GHz device close to the headphones or Bluetooth® device.

- Verify that both devices are placed within the recommended distance.

f. Difficulty in listening to a caller when receiving a call.

- Check if the headphones are connected to the Bluetooth® device.

- Verify if the Bluetooth ^® mode is enabled on your device.

- Check the volume level on your Bluetooth® device.

Technical specifications

MPN KWH-150
Headphone
Form factor	On-ear
Driver unit	Φ40mm
Maximum power output	20mW
Frequency	20Hz-20kHz
Impedance	32Ω±15%
Sensitivity	105±3dB/mW (S.P.L at 1kHz)
Microphone
Form factor	Built in
Directivity	Omnidirectional
Frequency	100Hz-18kHz
Impedance	32Ω
Sensitivity	105dB at 1kHz
Volume control	Yes
Connectivity
Connection type	Bluetooth®V5.0, 3.5mm auxiliary-in
Wireless RF frequency	2.402-2.480GHz
Wireless range	Up to 33ft*
Buttons	▶▶+ : volume+/next song, ▶II : play/pause/answer-hang up call/Redial Call/ Reject Call/→ ◀◀: volume-/previous song, and Power On/OffSwitch
Wired connection	AUX 3.5mm
Battery
Battery type	Built-in rechargeable lithium battery3.7VDC, 500mAh
Battery charging time	Up to 3.5 hours
Battery run time	Up to 18hrs @50% and up to 13H @100% volume**
Battery standby time	30 hours
Other features
Notifications type	Tones
Foldable	Yes
Additional Information
Cable length	About 3.9ft
Material	ABS
Dimensions (LxWxH)	6.8x2.9x7.2in
Weight	12.6oz
Warranty	One year

* Range estimate is based on an area free and clear of obstacles and interference, and within the line of sight between devices.
** Depending on the volume level and type of music file being played.

Precautions

• Do NOT drop, hit or shake the device.
• Do NOT disassemble, repair or modify the headphones yourself.
• Do not use cleaning products that contain benzene, solvents or alcohol.
• Do NOT expose headphones to excessive heat or to direct sunlight for long periods of time.
• Do NOT store the device in a place with high humidity or dust.
• Do NOT place heavy objects on top of the headphones.
• Do NOT use near a microwave oven or wireless LAN products.

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

I. Introducción

Notes/NotasNotes/Notas

klipxtreme

KlipXtreme® is a registered trademark. All rights reserved. The Bluetooth® word mark is owned by Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. Any mention of such is only intended for identification purposes, and is not to be construed as a claim to any rights pertaining to, sponsorship by, or affiliation with, those brands. Made in China.