SCMS-1621 - Saw Ozito - Free user manual and instructions
Find the device manual for free SCMS-1621 Ozito in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Sliding Compound Miter Saw |
| Model | SCMS-1621 |
| Motor Power | 1200 W |
| Blade Diameter | 210 mm (8 in) |
| Arbor Size | 15.88 mm (5/8 in) |
| No-Load Speed | 4500 min⁻¹ |
| Maximum Bevel | 45° Left |
| Miter Range | 0° to 45° Left and Right |
| Cutting Capacity (90°) | 60 mm x 120 mm |
| Cutting Capacity (45°) | 40 mm x 80 mm |
| Weight | 6.8 kg (15 lb) |
| Power Supply | 230 V ~ 50 Hz |
| Laser Guide | Built-in laser for precise cuts |
| Dust Collection | Compatible with 35 mm vacuum adapter |
| Table Extension | Sliding rails for wider workpieces |
| Safety Features | Electric brake, spindle lock, transparent blade guard |
| Maintenance | Regularly clean dust, lubricate sliding rails, check brush wear |
| Included Accessories | Carbide-tipped blade, dust bag, wrench, work clamp |
Frequently Asked Questions - SCMS-1621 Ozito
How do I replace the blade on my Ozito SCMS-1621?
Unplug the saw. Use the spindle lock to hold the arbor, then loosen the arbor bolt with the supplied wrench. Remove the old blade and install the new one with teeth facing forward. Tighten the bolt securely.
What is the maximum cutting capacity at 90 degrees?
At 90 degrees, the saw can cut up to 60 mm in height and 120 mm in width when using the sliding feature.
How do I adjust the miter angle?
Loosen the miter lock handle, rotate the table to the desired angle (0° to 45° left/right), and tighten the lock. Use the positive stops for common angles.
How do I adjust the bevel angle?
Release the bevel lock lever, tilt the saw head to the desired angle (up to 45° left), and retighten the lever. Ensure the bevel scale reads correctly.
Why is my laser guide not working?
Check if the batteries are dead (usually 2x AAA). Replace them. Also ensure the laser switch is turned on. If still not working, consult a service center.
Can I use a different blade size?
Only use blades with 210 mm diameter and 15.88 mm arbor. Using other sizes may damage the saw or cause injury.
How do I clean and maintain the saw?
Unplug the saw. Use a brush or vacuum to remove dust from the blade guard, rails, and miter base. Lubricate sliding components with a dry lubricant. Check carbon brushes every 50 hours of use.
The saw stops suddenly during use. What should I do?
It may be triggered by overload protection. Allow the motor to cool for a few minutes. Check the power cord and circuit breaker. If it persists, inspect for jammed blade or motor issue.
How do I zero the miter scale?
Loosen the miter lock, rotate the table to 0° and check alignment with a square. If off, loosen the pointer screw, adjust, and retighten.
Is the saw suitable for cutting metal?
This saw is designed for wood and wood-based materials. Do not cut metal unless using a specific metal-cutting blade and following safety precautions; overloading may damage the saw.
User questions about SCMS-1621 Ozito
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Saw in PDF format for free! Find your manual SCMS-1621 - Ozito and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SCMS-1621 by Ozito.