MSW-3000U - Saw Ozito - Free user manual and instructions

Product Type	Sliding Compound Miter Saw
Brand	Ozito
Model	MSW-3000U
Power Supply	240V ~ 50Hz
Power Input	1500W
No-Load Speed	4500 RPM
Blade Diameter	254 mm (10")
Arbor Size	30 mm
Max Bevel Capacity	45° left, 3° right
Max Miter Capacity	45° left, 45° right
Cutting Capacity at 90° (Crosscut)	120 x 70 mm
Cutting Capacity at 45° (Bevel)	120 x 50 mm
Dust Extraction Port	35 mm
Laser Guide	Yes, with on/off switch
Sliding Mechanism	Linear ball bearing rails
Table Extension	Yes, left and right
Clamping System	Vice clamp included
Weight	15.5 kg
Dimensions (L x W x H)	620 x 480 x 430 mm
Material	Aluminum base, steel fence
Cord Length	2.0 m
Safety Features	Electric brake, blade guard, safety switch
Warranty	3 years
Included Accessories	Carbide-tipped blade, dust bag, hex key, vice clamp
Recommended Use	DIY and light professional cutting

Frequently Asked Questions - MSW-3000U Ozito

How do I change the blade on the Ozito MSW-3000U saw?

Unplug the saw. Release the blade guard. Use the included hex key to loosen the arbor bolt (turn clockwise, as left-hand thread). Remove the old blade and install a new 254mm blade with the teeth facing forward. Tighten the arbor bolt securely, and lower the blade guard.

How do I adjust the bevel angle?

Loosen the bevel lock lever located at the rear of the saw base. Tilt the saw head to the desired angle (up to 45° left). Tighten the lock lever. Check the angle with a protractor if needed.

How do I set the miter angle?

Loosen the miter lock knob. Rotate the table to the desired angle (up to 45° left/right). The detents at common angles (0°, 15°, 30°, 45°) will click into place. Tighten the lock knob.

How do I use the laser guide?

Turn on the laser using the switch on the housing. The laser projects a red line indicating the cut path. Adjust laser alignment if necessary using the two adjustment screws (for left/right and up/down). The laser is not a substitute for measuring.

Why is my saw motor not starting?

Check that the power cord is plugged in and the circuit breaker hasn't tripped. Ensure the safety switch (if present) is engaged. Inspect carbon brushes; if worn, replace them. If the problem persists, contact Ozito service.

How do I maintain the sliding rails?

Keep the rails clean and lightly lubricated with a dry lubricant (e.g., silicone spray). Wipe off excess. Avoid using grease as it attracts dust. Check for debris periodically.

What safety precautions should I take?

Always wear safety glasses and hearing protection. Keep hands away from the blade. Use the included clamp to secure workpieces. Never force the saw; let the blade reach full speed before cutting. Disconnect power when changing blades or performing maintenance.

Can I use this saw for non-ferrous metals?

Yes, with appropriate metal-cutting blade. Replace the blade with one rated for aluminum or non-ferrous metals. Reduce feed rate to avoid overheating. Always check blade compatibility.

How do I attach a dust extractor?

Connect a 35mm vacuum hose to the dust port on the rear of the saw. Use the provided dust bag or connect to a shop vac for better dust collection. Ensure the hose is securely attached to prevent leaks.

Where can I find replacement parts?

Replacement parts are available from Ozito service centers or authorized dealers. Common parts include carbon brushes, blade, laser module, and arbor screw. Contact Ozito support or visit their website for a list of spare parts.

USER MANUAL MSW-3000U Ozito

We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category Example
Wear parts' Carbon brushes
Consumables' Saw blade
Missing parts

* Not necessarily induced in the scope of delivery!

In the effect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

• Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure? - What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Declaration of confirmity

Multi Purpose Saw MSW-3000U (Ozilo)
2014/25/EU	2009/42/EC
2005/82/EC_2009/125/EC	Annex IV Anex V Anex W Anex Y Anex Z Anex X Anex Y Anex Z Anex Y Anex Z Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y Anex Y AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexY AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS Anex S AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS Anexs AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS Anex AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS AnexS Anex

MSW-3000U

GB Additional operating & safety Instructions Multi Purpose Saw

Line drawing of a cylindrical tool labeled 'ozito' (no additional text or symbols)

Danger! Read the operating instructions to reduce the risk of inquiry

Caution! Wear car-muffs. The impact of noise can cause damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!

Caution! Wear safety goggles. Sports generated during working or splinters, chips and dust emitted by the device can cause loss of sight.

The reporting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the ISC GmbH.

Subject to technical changes

Items supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

- Open the packaging and take out the equipment with one

• Remove the packaging material and any

packaging and/or transportation braces (if available)

BVerkel.OB

- Check to see if all home are supplied. - Insect the equipment and accessories

- Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee period.

the end of the guarantee period

Danger!

The equipment and packaging material are not toys. Do not let children play with plastic bags, folls or small parts. There is a danger of swelling or swellingful.

Proper use

The multi-saw is designed for sawing wood, iron, non-ferrous metals and plastic. It should only be used with the appropriate saw blade.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voiced if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

Mains voltage: 230-240 V - 50 Hz

Power 500 W

Stroke rate: 500-3000/min

Stroke length 12 mm Cutting depth in wood 100 mm

Cutting depth in aluminium: 5 mm

Cutting depth in Mid Stock 3 mm

Protection class: IV E

Danger!

Sound and vibration

Sound and vibration values were measured in

according with EN 60745.

L_ss sound pressure level ....87 dB(A)

K, uncertainty 3 dB

L_out sound power level 98 dB(A)

K_no uncertainty

Wear ear-muffs.

The impact of noise can cause damage to hea-

ring

Total vibration values (vector sum of three direc-

ionsj determined in accordance with EN 60745.

Cutting wooden boards

Vibration emission value ah = 7.89 m/s²

Uncertainty K =

Cutting wooden beams

Vibration emission value sh = 6.82 m/s

Uncertainty K = 1.5 m/s

The specified vibration value was established in accordance with a standardized testing method. It may change according to how the electric equipment is used and may exceed the specified value in exceptional circumstances.

The specified vibration value can be used to

compare the equipment with other electric power

The specified vibration value can be used for ini-

al assessment of a harmful effect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect wor-

King order.

• Service and clean the appliance regularly.

- Adopt your working style to suit the appliance. - Do not overload too appliance.

- Do not open the appliance. - Have the appliance specified whenever

Halo de application of 100%

• Switch the appliance off when it is not in use.

• Wear protective gloves

Caution!

Residual risks

Even if you use this electric power tool in ac-

cordance with instructions, certain residual

risks cannot be rules out. The following har- rands may arise in connecting with the equin-

Zards may arise in connection with the eq. ment's construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

1. Damage to hearing if no suitable ear protecti

on is used.

1. Health damage caused by hand-term vibrations if the equipment is used over a pro-

dolls in the equipment is used over a prolonged period or is not properly guided and

maintained

For EU countries only

Never place any electric power tools in your

household refuse.

To comply with European Directive 2012/19/EC

concerning old electric and electronic equipment

and its implementation in national laws, old electric power tools have to be separated from other

his power tools have to be superior from other waste and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to

the manufacturer, the owner of the electrical equipment must make sure that the solution

equipment must make sure that the equipment is properly disposed of if he no longer wants to

to properly disposed of the no longer wants to keep the equipment. The old equipment can be

returned to a suitable collection point that will

disposse of the equipment in accordance with the

national recycling and waste disposal regulation. This does not apply to any purpose or side.

This does not apply to any accessories or tools without electrical components supplied with the

old equipment