55WD1485LW - Washing machine Ardo - Free user manual and instructions
Find the device manual for free 55WD1485LW Ardo in PDF.
| Product Type | Washing Machine |
| Brand | Ardo |
| Model | 55WD1485LW |
| Capacity (Max dry load) | 10 kg |
| Water Pressure | 0.05 - 1.00 MPa |
| Power Supply | 220-240 V, 50 Hz |
| Maximum Spin Speed | Up to 1400 RPM (model dependent) |
| Number of Programs | 15+ (including Cotton, Synthetics, Wool, Silk, Jeans, Dark, Sport, Delicate, Colored, Hand Wash, Quick, Spin, Rinses, Drying) |
| Special Features | Delayed start, Turbo, Prewash, Extra rinse, Drum disinfection, Child lock |
| Detergent Drawer | 3 compartments: prewash, main wash, softener |
| Drain Hose Height | 60 - 90 cm |
| Installation Type | Freestanding |
| Safety Features | Child lock, door interlock, overheating protection |
| Maintenance | Clean filter regularly, clean detergent drawer, wipe exterior |
| Accessories Included | Fill hose, drain hose, plugs for transport screws |
Frequently Asked Questions - 55WD1485LW Ardo
User questions about 55WD1485LW Ardo
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Washing machine in PDF format for free! Find your manual 55WD1485LW - Ardo and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 55WD1485LW by Ardo.
USER MANUAL 55WD1485LW Ardo
natural_image
Close-up of hands inserting a device into a drawer with arrows indicating direction (no text or symbols)COME ELIMINARE ALCUNE MACCHIE
Thank you for choosing our product.
Please read these instructions carefully before connecting and using the appliance.
Knowledge of the operating principles will help guarantee correct and safe use of the appliance. This instruction booklet contains the technical characteristics of the washing machine and is full of useful information regarding its operation, all designed to help you get the best out of your appliance. If the appliance is sold or handed over for use by others, remember to give the new user the instruction booklet.
MODEL:
DATE OF PURCHASE: / /
SERIAL NUMBER:
CONTENTS
TES AND ADVICE FOR THE USER 14-15
DESCRIPTION OF THE APPLIANCE 15
STALLING THE WASHING MACHINE 16-18
- Unpacking the washing machine and removing the locking devices 16
• Levelling the washing machine 16 - Connecting to the mains water supply 17
- Connecting to the mains electricity supply 18
ING THE WASHING MACHINE 18-20
- Recommendations prior to use 18
• Use of detergents 19
• How to remove some stains 20 • International clothing saw symbols 20
• International clothing care symbols 20
INTENANCE
Cleaning the washing machine 21
- Cleaning the filter 21
- Resciving problems 22
Before connecting the appliance read these instructions carefully. Repairing the failure arising from inappropriate connections or use of the appliance is not covered by the guarantee.
THE MANUFACTURER WILL NOT BE HELD RESPONSIBLE FOR ANY INCIDENTS RESULTING FROM NON-COMPLIANCE WITH SAFETY STANDARDS OR THE REQUIREMENTS OF THIS INSTRUCTION BOOK.
This appliance can be used by children aged from 8 years and above and person with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazard involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
▼ Children of less than 3 years should be kept away unless continuously supervised.
▼ The appliance must be properly connected to the system with new hoses provided. Used hoses must never be reused.
▼ The operating pressure of water (minimum and maximum) must be between 0.5bar (0.05MPa) and 10 bar (1 MPa).
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified person in order to avoid a hazard.
▼ Ventilation opening in the base must not be obstructed by a carpet.
▼ Observe the maximum volume of dry load as indicated in the section "Program Table".
▼ To stop the functions, refer to the washing guide.
Before using the washing machine, remove all the packing and locking devices used for the
touch the door glass either, as this will tend to heat up during washing.
Use the washing machine for machine-washable items only. In the case of any doubts, refer to the manufacturer's instructions on the label attached to the item to wash (see "Clothing care symbols")
Before placing the washing in the washing machine, make sure that all pockets are empty. Hard or pointed objects such as coins, pins, nails, screws or stones can cause serious damage to the appliance.
Never wash items that have been soiled with substances containing petrol. In the case where stains have been removed using vaporising products, wait until these substances have fully evaporated from the surface of the material before loading into the washing machine.
The use and quantities of detergent, softener and bleach must comply with the instructions reported on the packaging.
▼ Do not use detergents designed for hand washing, in that the excessive suds produced could damage the internal components.
▼ After washing mats, blankets or any other long-fibre materials, remove the filter and clean it if necessary.
▼ It is advisable to leave the door open at the end of the wash cycle.
Do not attempt to repair any appliance faults alone, in that repairs carried out by a non-professional may cause serious damage and will invalidate any rights to repairs under guarantee
NOTES AND ADVICE FOR THE USER
15
▼ Do not expose the appliance to atmospheric agents.
The washing machine can only be opened once the led or display indicates that the cycle has finished. On some models, this is signalled by a flashing start button.
▼ When servicing or cleaning the washing machine, remember to disconnect it from the
mains electricity supply.
▼ Do not pull the power supply cable to unplug the washing machine from the mains supply. Pull the plug only.
It is advisable to unplug the washing machine from the mains electricity supply and close-off the water supply after each wash.
FOR WASHER/DRIER VERSIONS:
▼ Never dry unwashed items.
▼ Do not dry items that have been washed or had stains removed using chemical products.
▼ Never dry items that have been soiled with substances such as cooking oil, petroleum, acetone, alcohol, petrol, kerosene, stain removers, turpentine, wax. Remove these substances in a hot wash using an abundant quantity of detergent prior to loading the items in the drier.
▼ Do not dry items such as foam rubber, latex, raincoats, waterproof fabrics, rubber mats, preformed items, clothes or
cushions with foam rubber padding, as these may melt and damage other items in the washing or even the appliance itself.
▼ Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
▼ Children of less than 3 years should be kept away unless continuously supervised.
▼ That the appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the appliance, in such a way that a full opening of the appliance door is restricted.
THE FINAL PART OF A DRYING CYCLE IS THE COOLING DOWN PHASE. CONSEQUENTLY, NEVER SWITCH OFF THE DRIER BEFORE THE CYCLE HAS BEEN COMPLETED. OTHERWISE, THE WASHING MUST BE TAKEN OUT QUICKLY AND HUNG OUT TO ALLOW THE HEAT TO DISSIPATE.
DESCRIPTION OF THE APPLIANCE
The washing machine has been constructed in steel panels which have been treated and painted to guarantees that its aesthetic qualities remain unaltered over time.
The motor and all moving parts have been designed and manufactured to guarantee the minimum possible noise levels
the washing much easier.
▼ The very high stability of the appliance is the result of constant research by our technicians into the equilibrium of masses in movement.
INSTALLING THE WASHING MACHINE
(according to the model)
Installation must be carried out by qualified personnel in line with the instructions supplied by the manufacturer. Incorrect installation may result in damage and injury.
The appliance can be installed anywhere providing that the ambient temperature is not less than 3^ C and that the wires or pipes on the rear of the machine are not squashed.
This appliance is intended to be used in household and similar applications such as:
▼ Staff kitchen areas in shops, offices and other working environments;
▼ Farm houses:
▼ By clients in hotels, motels and other residential type environments;
▼ Bed and breakfast type environments.
For transport reasons, the washing machine's oscillating group is locked in place by 4 spacers and screws. Before using the machine, remove the spacers and locking screws. Keep the screws and spacers for future use.
Close off the holes using the plugs supplied. The plugs can be found in the bag containing the documents.
For transport reasons, the washing machine's oscillating group is locked in place by 4 spacers and screws. Before using the machine, remove the locking screws with a suitable tool.
Insert a screwdriver in the holes and lever out the 4 plastic spacers as shown in the figure.
The washer/drier version must not be installed behind a locked door, a sliding door or with a hinged door on the opposite wall to the washer/drier itself.
LEVELLING THE WASHING MACHINE
After having selected the most suitable location for the appliance, make sure it is level by regulating the adjustable feel (Fig. 6).
Pay particular attention to the positioning and levelling of the washing machine and make sure that the lock nuts are tight.
If the appliance is not levelled correctly, it will be unstable and noisy and may cause damage.
INSTALLING THE WASHING MACHINE
17
CONNECTING THE WATER SUPPLY
The mains water pressure must be between 0.05 and 1.00 Mpa (0.5 - 10 bar.)
Before connecting the washing machine, open the valve and allow a certain quantity of water to flow out in order to clean the pipes of any sand or rust. This operation is particularly important in the case where the washing machine has been left standing for a long time or when connecting to a new water supply system.
The fill hose must be connected to the mains supply using a 510 " threaded connection.
On electronic washing machines fitted with a dual solenoid valve (hot and cold water), connect the red hose to the hot water supply valve and the other hose to the cold water supply valve.
If a hot water supply is not available, both hoses must be connected to the cold supply using the fitting supplied (see fig. 8). Do not connect to the hot water supply.
▼ Connect the fill hose (fig. 9).
Washing machines and condensation type washer/driers must be connected to the mains water supply using the new hoses provided with the appliance. The old hoses must not be re-used.
▼ During the wash, the water supply valve must be fully open.
▼ The drain hose must be positioned at a height of between 60 cm and 90 cm (fig. 10).
If the water is drained directly into the drainage system, the free end of the drain hose must be inserted in a pipe of internal diameter not less than 40 mm.
The drain hose connection to the drainage system must not be hermetically sealed, as this would cause a build up of air in the siphon and allow water to leak out.
INSTALLING THE WASHING MACHINE
CONNECTING TO THE MAINS ELECTRICITY SUPPLY
Make sure that the voltage indicated on the identification plate attached to the inside of the filter door corresponds to that of the mains supply (fig. 12).
All cut-outs, electric wiring and mains sockets must have a rating such that enables them to support the maximum load indicated on the identification plate.
Once the appliance has been installed, it must be connected to the mains supply through a single-pole switch.
The mains supply to which the appliance is connected must be fitted with an earthing system. If this is not the case, the manufacturer will not be held liable for any incidents that may occur (fig. 13).
If the mains socket to which the appliance is connected is faulty or unsuitable, it must be replaced by a qualified electrician.
The washing machine must not be connected to the mains supply using indirect methods such as extension leads or multiple adapters.
During maintenance work, the washing machine must be disconnected from the mains electricity supply.
Do not insert or remove the plug from the mains socket with wet hands.
If the power supply cable is damaged in any way, contact the appropriate specialised service centre.
The plug used to connect the machine to the power supply must never be fixed behind the machine, but must be in a position easily accessible in an emergency.
USING THE WASHING MACHINE
RECOMMENDATIONS PRIOR TO USE
Before carrying out the first wash, allow the washing machine to effect a short wash cycle without any washing.
This will allow the operation of the washing machine to be checked and will clean the drum.
Before each wash make sure that:
USING THE WASHING MACHINE
19
USE OF DETERGENTS
The washing machine is fitted with a three-compartment detergent drawer
↑compartment for pre-wash or soak soap powder (1)
2compartment for normal wash soap powder (2)
softener compartment (3)
Use a low-suds detergent and softener (if required) recommended for automatic washing machines. Follow the dosage instructions written on the packet.
Too much detergent can produce excessive suds and may result in a poor wash.
Too little detergent will produce an unsatisfactory wash.
When adding detergent to the dispenser, remember to avoid any spillage into the softener compartment, in that this would create a soapy rinse and stain the fabrics white. Vice versa, if softener is added to the detergent compartment, the quality of the wash will be compromised.
When using a liquid detergent (recommended for programmes without pre-wash) proceed as follows: remove the baffle from its housing at the front of compartment 2 and insert it in the guides near the centre of the same compartment.
natural_image
Person inserting a device into a drawer with arrows indicating process (no text or symbols)
USING THE WASHING MACHINE
HOW TO REMOVE SOME STAINS
Stains exist that cannot be removed by machine washing alone. Before trying to remove any type of stain by hand, first try the removal procedure on a small area of hidden fabric. Start from the edge of the stain and working inwards, this will prevent a dark ring from forming around the site of the stain. A few methods to adopt for removing stains are reported below.
WAX: Scrape the wax using a rounded point in order not to damage the fabric. Then, with the fabric placed between two pieces of absorbent paper, run a hot iron over the stain.
BALL POINT PENS AND FELT-TIP PENS: clean using a soft cloth soaked in ethyl alcohol. Take care not to spread the stain.
▼ DAMP AND MOULD: if the fabric supports the use of bleach, carry out a wash cycle adding bleach. Otherwise, soak the soiled part in hydrogen peroxide (10 volumes) and leave for 10 to 15 minutes.
LIGHT SCORCH MARKS LEFT BY IRONING: follow the instructions for mould and damp.
▼ Rust: use products specially designed for rust stains, following the manufacturer's instructions written on the packet.
▼ CHEWING GUM: rub ice over the fabric, scrape away as much chewing gum as possible and then rub with a piece of cotton soaked in acetone.
▼ PAINT: do not allow the paint to dry. Rub the area with the solvent recommended by the paint manufacturer (e.g. water, turps, trichloroethylene), soap and then rinse.
Lipstick: stains on cotton or wool can be eliminated using a cloth soaked in ether. Stains on silk require the use of trichloroethylene.
▼ NAIL VARNISH: place a sheet of absorbent paper on the stained material, then dampen the back of the fabric with acetone, frequently changing the absorbent paper placed over the stain. Continue in this manner until the stain has disappeared.
▼ TAR OR DIRT: spread a little fresh butter over the stain, allow to stand and then wash with oil of turpentine.
▼ GRASS: delicately soap the stain, use diluted bleach. Good results can be obtained on woollen fabrics using 90% alcohol.
▼ Blood: put into soak in cold water with added salt, then wash with washing soap.
INTERNATIONAL CLOTHING CARE SYMBOLS
Before placing the clothes in the washing machine and selecting the wash programme, examine the symbols on the manufacturer's label. The table reported below will provide a useful guide to reading the symbols.
Normal wash
Delicate wash
Wash at max 95°C
Wash at max 60°C
Iron at up to max 200°
Iron at up to max 150°
Iron at up to max 100°
Dry flat
Dry hanging
Dry on hanger
MAINTENANCE
CLEANING THE WASHING MACHINE
The washing machine has been specifically designed to reduce maintenance to a minimum. Nevertheless, it is important that it is cleaned regularly.
Before cleaning, make sure that the appliance has been disconnected from the power supply and that the water supply valve has been closed.
The external structure and the parts of the washing machine in plastic must be cleaned with a soft damp cloth only.
Never use chemicals, abrasive products, alcohol, soap, petrol or other solvents to clean the appliance as these may cause damage. (fig. 21)
After washing, leave the door open for a short time to allow rubber parts to dry.
Periodically wash out the detergent compartments. To do this, remove the detergent compartment and rinse it under running water (fig. 22). Then replace it.
REMOVING THE DETERGENT DRAWER
▼ open the detergent drawer;
▼ press on the word "PUSH" with the right hand and pull out the drawer with the left hand (fig. 23).
CLEANING THE FILTER
Before starting the operations described below, make sure that the washing machine is empty. Do not remove the filter while the washing machine is running, or when full of water.
Place a cloth or tray under the filter to collect any water that may still be inside Open the filter door, unscrew the filter and remove it by turning it in an anticlockwise direo-
MAINTENANCE
RESOLVING PROBLEMS
If the appliance is not working properly, check through the following troubleshooting guide before calling for technical assistance. In some models malfunctions are indicated by an error code displayed at the end of the cycle.
Code: E:00 Carry out all the checks listed in paragraphs marked with *
E:01 Carry out all the checks listed in paragraphs marked with **
E:02 Technical malfunction "Call Customer Service"
E:03 Technical malfunction "Call Customer Service"
The washing machine does not work (warning lights are off) (Display off)
Make sure that:
1) The mains power supply is working
2) The plug is inserted correctly in the socket.
(3) The On/On button has been pressed, or if not present, check that the programming knob is positioned on a programme.
The washing machine does not work (warning lights are off) (Display lit)\*
Make sure that:
1) The programme has been selected
2) The door is closed properly
3) The "Start" button has been pressed (elec
4). Refer to the information provided for "The
4) Here to the information provided for the washing machine does not fill with water"
The washing machine does not fill with water\* • Check that:
1) There is water in the water supply system
2) The water fill pipe is connected to the washing machine
3) The mains water supply valve is open
4) The filter is not blocked if it is, clean the filter after first unplugging the appliance from the power supply
The washing machine continuously fills and drains the water\*\*
Check that:
1) The drain hose has been installed at the cor-
rect height (60-90 cm)
2) The end of the drain hose is not under water
The washing machine does not drain or spin ^** • Check that:
4) The closing
1) The drain hose is properly connected. 2) The drain hose is not limited.
2) The drain hose is not linked
tion have been removed.
2) The washing machine is perfectly level
3) Bulky items such as sheets, tablecloths etc. are not all bundled in one part of the drum
The door will not open
• Make sure that:
1) The wash cycle has finished.
2) The Stop with water function has not been
selected (automatic on some models).
The washing has not been spun properly
• Make sure that:
1) The washing is evenly distributed in the drum
2) The correct spin speed has been selected
The washing machine stops during a wash
Make sure that.
1) The mains power supply is working
There is still a lot of detergent in the compartment
• Make sure that:
1) The mains water supply valve is open
2) The filter between the valve and the supply hose is clean
The washing is not clean at the end of the wash cycle
Make sure that:
1) The drum has not been overloaded
2) The correct amount of detergent has been used
3) The correct programme has been selected
The washing has shrunk or faded
• Make sure that:
1) The correct washing programme has been selected
2) The correct washing temperature has been selected
The washing machine does not dry (washer-driver models only)
ARDO
ARDO
GUIDA AL LAVAGGIO
Detergent drawer:
1 Prewash
Sollener
2 Washing
Control panel:
A LCD Display
B Delay/lock control button
C Spin button
D Prewash/disinfection button
E Turbolock control button
F Rinse button
G Dry button
H Start/pause Button
I Program setting knob
WASH IN THE CORRECT WAY
Before attempting to operate the washing machine, ensure that the installation has been performed correctly, as described in the instruction booklet.
Daily use
- Before putting clothes in the washing machine, empty the pockets of any hard or sharp object (nails, screws, coins, pins and stones) that may damage the machine and garments.
- To improve washing performance, introduce laundry into the washing machine without compressing it or overloading the machine. A whole load of highly absorbent fabrics, such as bathrobes and towels, can unbalance the machine during the spin cycle. The automatic load balancing system arranges laundry in the most even manner possible, and sets the optimum spin speed to minimise any vibrations.
- Close the door making sure that garments are not caught between the seal and the door.
- Put the correct amount of detergent in the drawer 2. Insert the bulkhead supplied if you are using liquid detergent. If you want to enable the prewash option, add the detergent in the drawer 1. Use the drawer marked with the special symbol for the softener. After adding the detergent, gently close the drawer.
- Select the wash program most suitable to the type of fabrics by using knob I following the instructions in the programs table. The LCD display will show the duration of the selected program with a full load. The remaining time may vary during the course of the wash cycle according to the load. The word End will appear on the display at the end of the cycle.
- Pressing the C button, a different spin speed to that provided by the selected program can be set. The B button allows you to delay the start of the wash cycle up to a maximum of 19 hours. Both values are shown on the LCD Display.
CONTROL PANEL
LCD DISPLAY: The large LCD display ensures quick and intuitive use of the washing machine. The display shows the wash options enabled, any delayed start, spin speed selected and the time remaining until the end of the cycle. The word End means that the door has been released.
After a few seconds, from the end of the wash cycle, the display switches off with the word End. To reactivate the display, press any button on the display.
DELAYED START: This feature allows you to delay the start of the wash cycle up to a maximum of 19 hours. Press the B button repeatedly until the display shows the desired start delay. The icon : flashes on the display until the start of the wash cycle. Confirm by starting the washing cycle using the START function.
When the function is activated, the display will turn off the backlight after a few seconds to save energy. To reactivate, press any button on the display.
RINSE: Press the F button to activate the extra rinse function. This option is recommended if your skin is particularly sensitive to enzymes in detergents.
PREWASH: To perform a prewash, press the D button and put the detergent in the drawer 1. The washing machine performs a prewash cycle at 40°C, max. Prewash is recommended for garments soiled with dust, dirt and sand or with particularly stubborn stains. See the program table for further information.
TURBO: Press the E turbo button to reduce the wash time. The operating parameters are automatically adjusted to ensure washing effectiveness and to allow time to be saved. See the program table for further information.
ADJUSTABLE SPIN Pressing the C button, the spin speed can be adjusted depending on the wash program selected and the type of fabric. The LCD display will show
CONTROL PANEL
DRYING: Drying activate the option, the display will show the symbol - indicating the level of drying and duration (in min). In the case in which has been selected at the beginning of the drying cycle the washing program, this will start automatically and the total time on the display means of washing + drying. Until we will begin the process of drying, you can change the time by touching the button on the display, putting the machine to pause (see Start/Pause). With this option enabled no you can exclude the spin cycle and put in the basket dispenser detergents, during drying, can melt and damage linen and washing machine.
To achieve the best drying performance of clothes washed, the maximum load of washing declared (see program table), you should run this cycle in two phases with a maximum load does not exceed the value stated on the rating plate.
START/PAUSE: When programs and wash options are being selected, the start LED remains off. To confirm your selection and start the wash cycle, press the H button. The LED turns on. During the wash program in progress, the cycle can be stopped by pressing the START/PAUSE button for a couple of seconds.
At this point, the wash program stops and you can make changes to the wash options (enabled depending on which stage of the wash cycle you are in). If the water temperature is below 50°C, the door can be opened (about 2 minutes after enabling
the pause function) to load/empty any laundry. To re-enable the wash phase press the START/PAUSE button again.
N.B. if, during a pause, no operation is carried out, the wash phase will restart automatically after 5 minutes.
CONTROL LOCK (child safety lock): to activate the control panel lock, simultaneously press the B-E (lock symbol) buttons; three horizontal lines will appear on the display.
If, during the wash cycle or at the end of the cycle, you wish to reactivate the controls, press buttons B-E simultaneously, until the three horizontal lines disappear.
DISINFECTING THE DRUM w-θ: Frequent washes at low temperatures may encourage the formation of mildew and unpleasant colours inside the washing machine. The DRUM DISINFECTION function thoroughly cleans the machine with a special cycle at 90°C.
DRUM DISINFECTION automatically recommends, through the blinking of the abbreviation [dm] the display, that you start the cleaning program after a certain number of washes, if high temperature cycles have not been selected during the period.
Remove all laundry from the drum, put the knob I on the DRUM DISINFECTION program and press the start H button to start the cycle.
PROGRAM TABLE
| Programs | Type of laundry | Maximum spin speed (rev/min) | Maximum load depending on the model and the program selected (kg) | Options | |||
| Symbols | Temperature (°C) | 10.0 | 5.0 | 8.0 | |||
| COTTON | 90°C Max | White lineders and heavily soiled cotton, including organic stains. | |||||
| 60°C Max | This cycle of washing, centrifuge and drying roller components to the standard of reference in accordance with the standard EN50229. | ||||||
| 40°C Max | The program ensures the best cleaning of 90°C, 40°C with the maximum saving of electricity. | ||||||
| WOOL | 40°C 800 | The wool program is ideal for washing do cate itons with labo's stating "machino" and "a" ensures colour care and that garments stay in good shape. | |||||
| SILK | 30°C 500 | The special jeans program gently washes at 40°C, taking care of the denim fibres and silbils, 40°C preventing colours from running. Faded denim garments will always come out looking like new. | |||||
| JEANS | 40°C 800 | ||||||
| SYNTETICS | 60°C 800 | The program reduces ironing time. The temperature, water level, intensity of washing and spin speeds are adjusted electronically to prevent creases and making ironing easier. | |||||
| SHIRTS | 40°C 500 | Designed for black and dark coloured cottons, mixed cottons and polyester garments. Special 40°C and 50°C colours from fading. You should use a special liquid detergent for dark coloured garments. | |||||
| DARK | 40°C Max | ||||||
PROGRAM TABLE
13
| Programs | Type of laundry | Maximum spin speed (rev/min) | Maximum load depending on the model and the program selected (kg) | Options | |||
| Symbols | Temperature (°C) | 10.0 | 20.0 | ||||
| SPORT | 40°C 800 | The sportswear program is designed for sports and casual wear. The 40°C wash cycle helps retain the shape of the fabric and the elasticity of modern synthetic fibers. | |||||
| DELCATED | 40°C 500 | Synthetic, polyester or other artificial fibre and sprouts shaping bags, bath melts, etc. | |||||
| COLOURED | 30°C Max | The colour program allows you to wash different coloured garments together; you can satisfy wash light and dark coloured laundry without any risk colours running. | |||||
| HAND WASH | 20°C 500 | Delicate garments require special care and are usually band washed. The specific hand wash option ensures garments are washed gently. | |||||
| SPIN | - Max 10 | The spin speed is adjustable to suit every type of fabric. | |||||
| RINSES | - Max 10 | The rose program is useful for re-rising 10.0 to 20.0 laundry or for refreshing items that have been stored for a long time. | |||||
| QUICK | 35°C 800 | Quick wash cycle is suitable for refreshing, in just 20 minutes. Lightly solid laundry. Quick to have you precious time, performing a wash cycle at 35°C. | |||||
| DRYNG | -- | The Dry program allows you to dry those clothes already washed that only require drying, also useful to remove moisture from clothing that has to be stored for a long time. If the laundry is a lot well, to save time and energy, do a spin cycle before drying. | 6.04.0 | 5.04.0 | 5.03.0 | ||
(*) Actual water temperature may differ from that indicated in the program.
TECHNICAL SPECIFICATIONS
NOTES
ARDO
- COME ELIMINARE ALCUNE MACCHIE
- CONTENTS
- THE MANUFACTURER WILL NOT BE HELD RESPONSIBLE FOR ANY INCIDENTS RESULTING FROM NON-COMPLIANCE WITH SAFETY STANDARDS OR THE REQUIREMENTS OF THIS INSTRUCTION BOOK.
- NOTES AND ADVICE FOR THE USER
- FOR WASHER/DRIER VERSIONS:
- DESCRIPTION OF THE APPLIANCE
- INSTALLING THE WASHING MACHINE
- LEVELLING THE WASHING MACHINE
- CONNECTING THE WATER SUPPLY
- CONNECTING TO THE MAINS ELECTRICITY SUPPLY
- USING THE WASHING MACHINE
- RECOMMENDATIONS PRIOR TO USE
- USE OF DETERGENTS
- HOW TO REMOVE SOME STAINS
- INTERNATIONAL CLOTHING CARE SYMBOLS
- MAINTENANCE
- CLEANING THE WASHING MACHINE
- REMOVING THE DETERGENT DRAWER
- CLEANING THE FILTER
- RESOLVING PROBLEMS
- The washing machine does not work (warning lights are off) (Display off)
- The washing machine does not work (warning lights are off) (Display lit)\*
- The washing machine does not fill with water\* • Check that:
- The washing machine continuously fills and drains the water\*\*
- The washing machine does not drain or spin ** • Check that:
- The door will not open
- The washing has not been spun properly
- There is still a lot of detergent in the compartment
- The washing is not clean at the end of the wash cycle
- The washing has shrunk or faded
- ARDO
- GUIDA AL LAVAGGIO
- Detergent drawer:
- WASH IN THE CORRECT WAY
- Daily use
- CONTROL PANEL
- TECHNICAL SPECIFICATIONS
- NOTES
Brand : Ardo
Model : 55WD1485LW
Category : Washing machine