Intrepid 3800 - SSD Drive OCZ - Free user manual and instructions

Product Type	Solid State Drive (SSD)
Brand	OCZ
Model	Intrepid 3800
Form Factor	2.5-inch
Interface	SATA III (6 Gb/s)
Capacity	240 GB
NAND Flash Type	MLC
Sequential Read Speed	Up to 550 MB/s
Sequential Write Speed	Up to 520 MB/s
Random Read IOPS	Up to 90,000
Random Write IOPS	Up to 80,000
Power Consumption (Active)	2.5 W
Power Consumption (Idle)	0.5 W
MTBF	2,000,000 hours
Operating Temperature	0°C to 70°C
Dimensions (W x D x H)	100.2 x 69.85 x 7.0 mm
Weight	70 g
Maintenance	No user-serviceable parts. Clean with a dry soft cloth.
Safety	Handle with care; avoid static discharge. Keep away from liquids.
Spare Parts and Repairability	Non-repairable; replace unit if faulty.

Frequently Asked Questions - Intrepid 3800 OCZ

How do I install the OCZ Intrepid 3800 SSD in my computer?

Install the SSD in a 2.5-inch drive bay or use a mounting bracket for 3.5-inch bays. Connect the SATA data cable to the motherboard and the SATA power cable from the power supply. Secure the drive with screws.

Do I need to format the SSD before use?

If the SSD is new, it may require initialization and formatting. In Windows, open Disk Management, initialize the disk as GPT or MBR, then create a partition and format with NTFS.

Can I use this SSD with a laptop?

Yes, the 2.5-inch form factor is standard for most laptops. Ensure your laptop has a SATA interface and sufficient clearance for 7mm thickness.

What is the expected lifespan of the OCZ Intrepid 3800?

The drive has an MTBF of 2,000,000 hours. Actual lifespan depends on usage, typically lasting several years under normal workloads.

Does the SSD support TRIM?

Yes, the OCZ Intrepid 3800 supports the TRIM command, which helps maintain performance over time. Ensure TRIM is enabled in your operating system (default in Windows 7 and later).

How can I check the health of my SSD?

Use monitoring software such as CrystalDiskInfo or OCZ's own toolbox. These tools report S.M.A.R.T. data including wear level, remaining life, and bad blocks.

Is the drive compatible with macOS or Linux?

Yes, SATA SSDs are universally compatible. Format the drive in a compatible filesystem like APFS (macOS) or ext4 (Linux) after installation.

What should I do if my computer does not recognize the SSD?

Check cable connections, try a different SATA port or cable, and ensure the drive is detected in BIOS/UEFI. If not, test the drive in another system to rule out hardware failure.

Can I use the SSD as an external drive?

Yes, with a SATA-to-USB adapter or enclosure. Ensure the enclosure supports 2.5-inch SATA drives. The drive will appear as an external storage device.

Does this SSD have any special security features?

The OCZ Intrepid 3800 does not include built-in hardware encryption. For data security, use software encryption like BitLocker or FileVault.

USER MANUAL Intrepid 3800 OCZ

Supported operating systems 1

System requirements....1

Installation as a Boot Device 2

Install the hardware 2

Install the operating system on the Intrepid 3000 ....2

Set the Intrepid 3000 as a boot device ....2

Installation as a Storage Device 3

Install the hardware 3

Set up the Intrepid 3000 as storage....3

Prolonging the Life of Your SSD 4

Limited Warranty 5

© OCZ Technology Group, Inc. 2013. All Rights Reserved. The information in this document is proprietary and confidential to OCZ Technology Group, Inc. (OCZ). No part of this document may be reproduced in any form or by any means, and may not be used to make any derivative work (such as translation, transformation, or adaptation) without written permission from OCZ.

OCZ provides this documentation without warranty, term or condition of any kind, either express or implied, including, but not limited to, express and implied warranties of merchantability, fitness for a particular purpose, and non-infringement. While the information contained in this document is believed to be accurate, no representations or warranties of accuracy or completeness are made. In no event is OCZ liable for damages arising directly or indirectly from any use of or reliance upon the information contained in this document.

OCZ retains the right to make changes to this product and/or the program(s) described in this documentation at any time, without notice. Products may have minor variations to this publication, known as errata. OCZ assumes no liability whatsoever, including infringement of any patent or copyright, for sale and use of OCZ products.

OCZ and the OCZ logo are registered trademarks of OCZ Technology Group, Inc.

All product names are trademarks, registered trademarks, or servicemarks of their respective owners.

The OCZ Intrepid 3000 Series product is protected by U.S. and international copyright and other intellectual property laws. Do not lend or make illegal copies. Use of OCZ Intrepid 3000 Series is subject to compliance with applicable license terms and conditions.

Installation Technical Support

OCZ products include free technical support for direct, expert advice.

For installation technical support, you can contact us by:

Visiting http://ocz.com/enterprise/support

Calling OCZ Technical Support at (US toll-free) [phone] or (Europe) [phone] (dial 1 for support)

Emailing us at [e-mail]

Writing to OCZ Technology Group, Inc., 6373 San Ignacio Avenue, San Jose, CA 95119 USA.

Document identifier: ISF-UserGuide-IT3, Revision 1, November 2013

Welcome!

intrepid

The OCZ Intrepid 3600 and 3800 SSDs (Intrepid 3000) are enterprise level 2.5" SATA devices that are designed to solve enterprise storage challenges caused by the limitations hard drive technology imposes on IT infrastructures. The Intrepid 3000 delivers the industry's best-in-class steady state performance for enterprise class SATA SSDs.

You can use the Intrepid 3000 as a boot device or as a storage device. This guide contains instructions for both uses. The instructions assume that you are an experienced IT administrator and have access to the full user information for your systems.

At OCZ our primary goal is to ensure that every customer is 100% satisfied. If you have any questions during or after the installation process, please contact our industry-leading field sales engineering team using the details inside the front cover of this guide.

Supported operating systems

Intrepid 3000 supports both 32-bit and 64-bit x86 architectures. Please update your operating systems to the latest Service Pack or release. Supported operating systems are:

• Windows 7
• Windows 8
  • Windows Server 2008 R2
  • Windows Server 2012
  • Linux - major distributions with kernel 2.6.32 to 3.8

System requirements

Intrepid 3000 minimum system requirements are:

• 2.5" drive bay
- motherboard that supports SATA, or a SATA Host Bus Adapter (HBA) card
• SATA cable to connect the drive to the SATA connector on the motherboard or SATA HBA card
- if you are using a SATA HBA card, you must ensure there is sufficient space to install it
- latest driver for the SATA controller (motherboard or SATA HBA card)
- minimum system memory as required by the operating system (for instructions on increasing memory, see your system user guide)

For optimal performance, we recommend that you also have SATA 3.0 (6Gbit/s) support (motherboard or SATA HBA card).

Installation as a Boot Device

intrepid

To set up the Intrepid 3000 as a boot device, you:

1 Install the hardware.
2 Install the operating system on the Intrepid 3000.
3 Set the Intrepid 3000 as a boot device.

The following instructions are a general guideline for installation in Windows 7; it is assumed that you have access to the system user guide for full instructions. To install in other Microsoft operating systems or Linux, see the relevant operating system guides.

Install the hardware

1 Install the Intrepid 3000 into the drive bay. Use the supplied screws to properly secure the Intrepid 3000.
2 If the motherboard is not SATA compatible, install the SATA HBA card into the system. For full instructions, consult the SATA HBA card user guide.
3 Connect one end of the SATA cable to the Intrepid 3000 and the other end to the SATA connector on the SATA compatible motherboard or SATA HBA card.
4 Connect the power cable from the power supply to the Intrepid 3000.

Install the operating system on the Intrepid 3000

1 Check in the motherboard or the SATA HBA card user guide whether any driver is needed during the Windows installation. Download drivers to a CD or memory stick.
2 Set the boot order in the system BIOS to boot from the Windows installation CD in the CD drive. For detailed instructions on how to access the BIOS and modify its settings, see the system user guide.
3 Boot from the CD and follow the onscreen Windows installation instructions.
4 On the Where do you want to install Windows? window, if the Intrepid 3000 is listed, select it and click Next.
If the Intrepid 3000 is not listed, install the driver from step 1: click Load Driver and load it from the CD or memory stick. Once the driver is loaded, the Intrepid 3000 is listed. Select it and click Next.
5 Follow the remaining onscreen instructions to complete the installation.

Set the Intrepid 3000 as a boot device

To set the Intrepid 3000 as a boot device, you must change the boot order in the motherboard BIOS. For full instructions on how to access the BIOS and modify its settings, see the system user guide.

Set the Intrepid 3000 to the primary boot device. Ensure that you save the settings before exiting the BIOS.

Installation as a Storage Device

intrepid

To use the Intrepid 3000 as a storage device:

1 Install the hardware.

2 Set up the Intrepid 3000 as storage.

The following instructions are a general guideline for installation in Windows 7; it is assumed that you have access to the system user guide for full instructions. To install in other Microsoft operating systems or Linux, see the relevant operating system guides.

Install the hardware

1 Install the Intrepid 3000 into the drive bay. Use the supplied screws to properly secure the Intrepid 3000.
2 If the motherboard is not SATA compatible, install the SATA HBA card into the system. For full instructions, consult the SATA HBA card user guide.
3 Connect one end of the SATA cable to the Intrepid 3000 and the other end to the SATA connector on the SATA compatible motherboard or SATA HBA card.
4 Connect the power cable from the power supply to the Intrepid 3000.

Set up the Intrepid 3000 as storage

1 Check in the motherboard or the SATA HBA card user guide whether any driver is needed for Windows operation. Download drivers to a CD or memory stick.
2 Switch on and start up the computer.
3 Click the Windows Start button in the taskbar, right-click Computer and select Manage. The Computer Management window is shown.
4 In the left pane, expand Storage then click Disk Management. Available disks are listed.
5 Select the Intrepid 3000. If you have not previously initialized it, wait for the Initialize Disk window to load and click OK to initialize it. When finished, the Disk Management window is shown again. If the Intrepid 3000 is already initialized, go to step 6.
6 To format the drive, right click unallocated disks and select New Simple Volume.
7 Follow the onscreen instructions to finish formatting the drive.
Your Intrepid 3000 is now ready to use for storage.

Prolonging the Life of Your SSD

intrepid

To prolong the life of your Intrepid 3000, you can update the Intrepid 3000 firmware.

To obtain the latest firmware and firmware updating tools:

1 Go to http://ocz.com/enterprise/download/firmware. Read the notes at the bottom of the web page carefully.
2 Download the OCZ Toolbox or clout utility as required for your operating system.
3 Ensure that you have a valid internet connection on your system.
4 Start the Toolbox or clout and select the relevant SSD to update the firmware.

You must log on as an administrator when using the OCZ Toolbox.

Limited Warranty

OCZ Technology products epitomize the new vanguard of quality standards as part of our commitment to our customers. All OCZ Technology Group ("OCZ") products are warranted and tested to be free from defects in material and workmanship and to conform to the published specifications. Should your OCZ product fail within the warranty period (under normal use in the recommended environment) due to improper workmanship or materials, OCZ will repair the product or replace it with a comparable or better unit. This warranty is subject to the conditions and limitations set forth herein.

Duration of warranty

The OCZ Intrepid 3000 is covered by this warranty for 5 years from the date-of-purchase. Proof-of-purchase including the date-of-purchase is required to collect on the warranty. OCZ will inspect the product and decide whether to repair or replace it. OCZ reserves the right to provide a functional equivalent product, or a refurbished replacement product.

Limitations

This warranty does not apply to product failure caused by accidents, abuse, mishandling, improper installation, alteration, acts of nature, improper usage, or problems with electrical power. In addition, opening or tampering with the product casing, or any physical damage, abuse or alteration to the product's surface, including all warranty or quality stickers, product serial or electronic numbers will also void the product warranty. OCZ is not responsible for recovering any data lost due to the failure of a flash memory device. OCZ products must be used with devices that conform to the recommended industry standards. OCZ will not be liable for damages resulting from a third party device that causes the OCZ product to fail. OCZ shall in no event be liable for any consequential, indirect, or incidental damages, lost profits, lost business investments, lost goodwill, or interference with business relationships as a result of lost data. OCZ is also not responsible for damage or failure of any third-party equipment, even if OCZ has been advised of the possibility. This limitation does not apply to the extent making it illegal or unenforceable under applicable law.