GZCA 1500.M2 - Receiver Ground Zero - Free user manual and instructions
Find the device manual for free GZCA 1500.M2 Ground Zero in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Audio Amplifier (Mono) |
| Brand | Ground Zero |
| Model | GZCA 1500.M2 |
| Power Output (RMS) | 1500 Watts @ 1 Ohm |
| Power Output (Max) | 3000 Watts |
| Frequency Response | 10 Hz - 250 Hz |
| Amplifier Class | Class D |
| Dimensions (L x W x H) | 11.0 x 7.1 x 2.2 inches (280 x 180 x 55 mm) |
| Weight | 3.5 kg (7.7 lbs) |
| Input Voltage | 12 V DC (10-16 V) |
| Input Sensitivity | 0.2 V - 6 V |
| Low-Pass Filter | 30 Hz - 250 Hz adjustable |
| Subsonic Filter | 10 Hz - 50 Hz adjustable |
| Bass Boost | 0 - 18 dB @ 45 Hz |
| Phase Shift | 0° / 180° switchable |
| Protection Features | Thermal, short circuit, overvoltage, undervoltage |
| Inputs | RCA, high-level speaker inputs |
| Outputs | Speaker terminals (2-ohm to 8-ohm load) |
| Remote Control | Bass remote control included |
| Recommended Fuse | 100 A (not included) |
| Materials | Aluminum heatsink, top-mount design |
Frequently Asked Questions - GZCA 1500.M2 Ground Zero
What is the recommended power wire gauge for the GZCA 1500.M2?
For a 1500W RMS amplifier, use 4 AWG power and ground wire for runs up to 20 feet. For longer runs, consider 0 AWG to minimize voltage drop.
Can this amplifier run at 2 ohms?
Yes, the GZCA 1500.M2 is 1-ohm stable, so it can safely drive a 2-ohm load. At 2 ohms, the RMS power output is approximately 1000 Watts.
Does the amplifier come with a remote bass control?
Yes, it includes a wired bass remote control for adjusting the bass level from the driver's seat.
What type of input does the amplifier accept?
It accepts both RCA inputs for aftermarket head units and high-level speaker inputs for factory stereos with speaker-level outputs.
How do I set the gain on the GZCA 1500.M2?
Set the head unit volume to about 75% of max, play a test tone (e.g., 50 Hz), and adjust the gain knob clockwise until you hear distortion, then back off slightly. Use a multimeter for precise setting.
What is the purpose of the subsonic filter?
The subsonic filter (10-50 Hz) removes extremely low frequencies that are below the audible range, reducing wasted power and preventing damage to the subwoofer by blocking sub-audible signals.
Can I run two subwoofers with this amplifier?
Yes, you can wire two subwoofers in parallel or series to achieve the final impedance. For example, two 4-ohm DVC subs wired to a 1-ohm final load will maximize the amplifier's power output.
Does the amplifier have a built-in crossover?
Yes, it features a low-pass filter adjustable from 30-250 Hz, and a subsonic filter. For high-pass, you will need an external crossover or use the head unit's settings.
What should I do if the amplifier goes into protect mode?
Check for short circuits in speaker wires, low battery voltage (below 10V), or overheating. Ensure the amplifier has adequate ventilation and the impedance load is correct (not below 1 ohm).
What is the maximum input voltage for the high-level inputs?
The high-level inputs can accept up to 6V RMS. If your factory head unit outputs higher voltage, use a line output converter to avoid distortion.
User questions about GZCA 1500.M2 Ground Zero
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual GZCA 1500.M2 - Ground Zero and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GZCA 1500.M2 by Ground Zero.