Ergorapido CX7-2-I360 - Electric broom AEG - Free user manual and instructions

Product Type	Cordless Stick Vacuum (Electric Broom)
Brand	AEG
Model	Ergorapido CX7-2-I360
Voltage	18 V DC
Battery Type	Lithium-ion
Battery Capacity	36.5 Wh
Runtime (Long Runtime Mode)	Approximately 35 minutes
Charging Time	Approximately 4 hours (24 hours for first use)
Dust Container Capacity	0.6 L
Weight	3.5 kg
Dimensions (Height)	110 cm
Filtration System	Washable fine filter and pre-filter
Brushroll	Motorized with BRUSHROLLCLEAN® function (on compatible models)
Accessories Included	Crevice nozzle, dusting brush, charging station
Power Regulation	Yes, adjustable between high and silent mode
Hand Unit Detachable	Yes, for handheld vacuuming
Charging Indicator	LED lights: slow blink when fully charged
Safety Features	Overheating protection for BRUSHROLLCLEAN® function

Frequently Asked Questions - Ergorapido CX7-2-I360 AEG

How do I charge the AEG Ergorapido CX7-2-I360?

Place the vacuum on the charging station connected to the mains. The charging indicator will light up. For first use, charge for 24 hours; subsequent charges take about 4 hours.

How long does the battery last on a full charge?

Runtime depends on model variant. For the CX7-2-I360, expect approximately 35 minutes in long runtime mode. High power mode reduces runtime.

How do I clean the filters?

Remove the dust container, press release buttons to take out filters. Separate the fine filter and pre-filter, rinse under lukewarm water without detergents. Let them dry for at least 12 hours before reinstalling.

What is the BRUSHROLLCLEAN® function and how do I use it?

This function automatically cleans the brush roll of hair and fibers. Place the vacuum on a hard, flat surface, turn it on, and press the BRUSHROLLCLEAN® pedal with your foot for 5 seconds. A cutting noise is normal. Avoid use on carpets.

How do I empty the dust container?

Press the release buttons on the dust container to remove it. Take out the filters, then empty the container into a dustbin. Do not wash the container or filters in a dishwasher.

What should I do if the brushroll gets blocked?

The vacuum will stop. Open the cable protector grill and brush roll hatch cover, remove the brush roll, and use scissors to cut away threads or debris. Ensure the brush roll spins freely before reassembling.

How can I maximize battery life?

Always keep the vacuum on charge when not in use. For long storage, charge to at least 50% and store at normal room temperature. Avoid extreme temperatures below 5°C or above 35°C.

Is the Ergorapido CX7 suitable for pet hair?

Yes, the BRUSHROLLCLEAN® function helps remove pet hair from the brush roll. Regular filter cleaning is recommended for optimal performance with pet hair.

How do I detach the hand unit for portable use?

Press the release button on the main body to detach the hand unit. You can then attach accessories like the crevice nozzle or dusting brush for cleaning furniture or car seats.

Where can I purchase accessories and spare parts?

Visit www.aeg.com/shop for consumables like filters (EF150) and car kits (KIT10B). Use the model number and PNC from the rating plate to find compatible parts.

USER MANUAL Ergorapido CX7-2-I360 AEG

Cordless vacuum cleaner

logcom/trap

Black vacuum cleaner with extended arm and base (no visible text or symbols)

c.10711

[Unreadable]
1

Technical line drawing of various electronic components including a coiled cable, plastic clip, and connector (no text or symbols)

BedPro™ MINI

Bez.: ZE125

Thank you for choosing an AEG CX7 vacuum cleaner. In order to ensure the best results, always use original AEG accessories and spare parts. They have been designed especially for your vacuum cleaner. This product is designed with the environment in mind. All plastic parts are marked for recycling purposes.

DESCRIPTION OF CX7

A. ON/OFF button	M. Dusting brush
B. Power regulation button	N. Crevice nozzle
C. ON/OFF button, hand unit	O. Cable protector grill
D. Locking screw	P. Hatch cover for brush roll
E. Release button, hand unit	Q. Brush roll
F. Charging station, wall unit	R. BRUSHROLLCLEAN* pedal*
G. Charging station, floor unit	S. Nozzle front lights
H. Charging adapter	T. Charging indicator
I. Fine filter (inner filter)	U. Cliff hanger
J. Pre filter (outer filter)	V. Slot for accessory storage
K. Release button, dust container
L. Dust container	* Not on models CX7-2-30xxx

BEFORE STARTING

Check that the package includes all parts described in this instruction manual and read this manual carefully. Pay special attention to the safety precautions chapter. Save these instructions.

1 Assemble the handle.
2 Assemble the charge stand.
3 There is a hollow space in the bottom of the charging station where unused cable can be wound. Insert the adaptor into the mains and position the charging station on a stable and horizontal surface away from heat sources, direct sunlight or wet places.
4 The charging indicator will be lit when CX7 is placed in the charging station.

CHARGING CX7

5 When fully charged, the charging indicator will blink slowly. The numbers of LED lamps will indicate the level of charge. Full charging time is around 4 hours. For better battery performance, charge CX7 for 24 hours before first use and always keep it on charge when not used.

VACUUMING WITH CX7

Before vacuuming, check that the nozzle wheels and the brush roll are clean from sharp objects in order to avoid scratching sensitive floors and to ensure full cleaning performance.

6 Start and stop CX7 by pushing the ON/OFF button. CX7 will start on the high power mode. For more silent cleaning and longer runtime, press the power regulation button.

VACUUMING FURNITURE, CAR SEATS ETC.

7 Press the button to release the hand unit from the main body.

8 Attach the crevice nozzle to facilitate cleaning of areas difficult to reach. Attach the brush on the crevice nozzle for dusting.

9 The crevice nozzle and small brush can be stored in the charging station or in the slot on the back side of the handle.

BRUSHROLLCLEAN® FUNCTION (CERTAIN MODELS ONLY)

Use the BRUSHROLLCLEAN® function to keep the brush roll clean and free from hair and fibres. For best results use the BRUSHROLLCLEAN® function when CX7 is fully charged.

10 Place CX7 on a hard and flat surface. Do not use the BRUSHROLLCLEAN ^ function on carpets.

Press the BRUSHROLLCLEAN ^® pedal with your foot while the cleaner is on. Hold for 5 seconds until hairs and fibres are removed. There will be a cutting noise during this process, this is normal. If hairs remain on the brush roll, repeat the process.

The BRUSHROLLCLEAN ^® function is equipped with an overheating protection. If the BRUSHROLLCLEAN ^® function has been used for more than 30 seconds (constant or interrupted) it will deactivate the brush roll and turn off the nozzle front lights. The vacuum cleaner can still be used, even when the BRUSHROLLCLEAN ^® function is deactivated. To reactivate the BRUSHROLLCLEAN ^® function, place CX7 on charge and charge for 15 minutes.

Please note that the BRUSHROLLCLEAN® function might not be able to

remove thicker threads or wires that are caught in the brush roll.

EMPTYING OF THE DUST CONTAINER

11 Remove the dust container by pressing the buttons.
12 Take out the filters from the dust container by pressing the release buttons. Empty the contents into a dustbin. Never wash the dust container or filters in a dishwasher.

IMPORTANT - FILTER CLEANING!

13 The filters must be cleaned at regular intervals to ensure a high cleaning performance. Take out the filters by pressing the release buttons. Separate the inner filter from the outer filter.
14 Rinse the filter parts carefully under lukewarm water without using any detergents. (Never use the dishwasher or washing machine.) Shake to remove excess water and leave to dry minimum 12h before putting them back into the cleaner.

CLEANING THE HOSE AND NOZZLE WHEELS

15 Loosen the hose behind the nozzle from its upper connection. Remove any object or debris that can be blocking the airflow in the hose or in the air channel to the dust cup, and put the hose back.
16 If the wheels need to be cleaned or get jammed, remove them carefully by using a flat screwdriver.

REMOVING AND CLEANING THE BRUSH ROLL

17 If the brushroll gets blocked CX7 will stop. Open the cable protector grill and the brush roll hatch cover and remove the brush roll.
18 Use a pair of scissors to remove threads etc. Reassemble the brush roll, making sure it can spin freely.

REMOVING THE BATTERIES FOR RECYCLING

Warning; Battery removal must only be done by an AEG service center or official collection point!

19 Only remove batteries if the product is to be scrapped. Improper handling of the batteries may be hazardous. Batteries should always be completely discharged before removal. Take your product to an AEG service center or official collection point for recycling. They can remove and recycle the battery and electric parts in a safe and professional way. Follow your country's rules for collection of rechargeable batteries and electrical products.

Enjoy a great cleaning experience with CX7!

SAFETY PRECAUTIONS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and maintenance shall not be made by children without supervision.

Batteries must be removed from the appliance before it is scrapped.

The battery is to be disposed of safely.

Only use the charging adapter that was provided with the product.

CX7 should only be used for normal vacuuming indoors and in a domestic environment. Make sure it is stored in a dry place.

Packaging material, e.g. plastic bags should not be accessible to children to avoid suffocation.

Never use the vacuum cleaner:

• In wet areas.
• Close to flammable gases, etc.
• When the product shows visible signs of damage.
• On sharp objects or liquids.
• On hot or cold cinders, lighted cigarette butts, etc.
• On fine dust, for instance from plaster, concrete, flour, hot or cold ashes.

Caution:

• Do not leave the vacuum cleaner in direct sunlight.
• Avoid exposing the vacuum cleaner to strong heat.
• The battery cells within must not be dismantled, short circuited or placed against a metal surface.
• Never use the vacuum cleaner without its filters.
• Do not try to touch the brush roll while the cleaner is switched on and the brush roll is turning.
• Mind your fingers if cleaning the inside of the floor nozzle. The metal blade of the BRUSHROLLCLEAN* function is sharp and could cause injury.

Using the vacuum cleaner in the above circumstances may cause serious personal injury or damage to the product. Such injury or damage is not covered by the warranty or by AEG.

SERVICING AND WARRANTY

All service or repairs must be carried out by an authorized AEG service centre.

This warranty does not cover reduction in battery runtime due to battery age or use, as the life of the battery depends upon the amount and nature of use.

To protect the motor, battery and electronics the product should not be stored or operated in:

• An ambient temperature below 5^ or exceeding 35^ . If the product is stored in a temperature below 5^ or exceeding 35^ , let the product cool down or warm up and dry for a few hours before usage.
  • A humidity level below 20% or exceeding 80% (non-condensing).

If the product is stored for an extended time period (without usage or continuous charging), we recommend to store the product in normal room temperature with the batteries charged at 50% capacity or more. This will maintain the performance of the product.

Attention! Dew condensation may form inside the product if the unit is moved from a cold to a warm environment or after heating up the storage room. Wait a few hours for the internal components to warm up and dry before usage.

INDICATION LAMPS

CHARGING	WHAT DOES IT MEAN?	DURING USAGE	WHAT DOES IT MEAN?
	Blink slowly = 100 % fully charged 75 – 100 % capacity
	50 – 95 % charged 50 – 75 % capacity remaining
	0 – 50 % charged 25 – 50 % capacity remaining
			CX7 needs to be recharged.

Get usage advice, brochures, trouble shooter, service information: www.aeg.com

Register your product for better service: www.aeg.com/productregistration

Buy Accessories and Consumables for your appliance: www.aeg.com/shop

CUSTOMER CARE AND SERVICE

When contacting the AEG service center, ensure that you have following data available:

• Model number,
• PNC number
• Serial number

The information can be found on the rating plate.

CONSUMABLES & ACCESSORIES

www.aeg.com/shop

Filter Ref: EF150 PNC: 900 168 3748

Car Kit Ref: KIT10B PNC: 900 167 9803

Technical line drawing of various electronic components including a coiled cable, plastic housing, and connector (no text or symbols)

BedPro™ MINI Ref: ZE125 PNC: 900 168 0819

RUNNING TIMES FOR CX7

Model Volt Long runtime mode
CX7-2-45xx 18V HD 45 min
CX7-2-35xx 18V 35 min
CX7-2-30xx 14,4V 30 min

The battery should be removed from The product before disposal. Dispose of or recycle The battery in accordance with local regulations. The symbol

on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

ΕΛΛΗΝΙΚΑ

Line drawing of a handheld electronic device with a gray component and a vertical line indicating measurement or alignment (no text or symbols)

Technical line drawing of various electronic components including a rectangular block, cable, and connector (no text or symbols)

BedPro™ MINI

Αναφ: ZE125

PNC: 900 168 0819

www.aeg.com/productregistration

Line drawing of a handheld electronic device with a button and handle (no text or symbols)

CONSUMIBLES Y ACCESORIOS

www.aeg.com/shop

Filtro

Ref: EF150

Número de producto (PNC): 900 168 3748

Kit para el coche

Ref: KIT10B

Número de producto (PNC): 900 167 9803

Technical line drawing of various electronic components including a coiled cable, plastic housing, and connector (no text or symbols)

BedPro™ MINI

Ref: ZE125

Technical line drawing of various mechanical components including a hose, clamped parts, and a clip (no text or symbols present)

BedPro™ MINI Réf: ZE125 PNC: 900 168 0819

AUTONOMIES POUR CX7

Technical line drawing of various electronic components including a coiled cable, plastic housing, and connector (no text or symbols)

BedPro™ MINI

Rif: ZE125

PNC: 900 168 0819

TEMPI DI UTILIZZO PER CX7

Modello Volt		modalitr tempo di utilizzoprolungato
CX7-2-45xx 18V	HD 45 min
CX7-2-35xx 18V	35 min
CX7-2-30xx 14,4V	30 min

VOOR U VAN START GAAT

Technical line drawing of various electronic components including a rectangular block, cable, and connector (no text or symbols)

BedPro™ MINI

Ref: ZE125

PNC: 900 168 0819

BEDRIJFSTIJDEN VOOR CX7

Model Volt Lange werkingstijd modus
CX7-2-45xx 18V HD 45 min
CX7-2-35xx 18V 35 min
CX7-2-30xx 14,4V 30 min

ASSISTÊNCIA E GARANTIA

Line drawing of a handheld electronic device with a gray rectangular component and a vertical line indicating a measurement or alignment point (no text or symbols present)

CONSUMÍVEIS E ACESSÓRIOS

www.aeg.com/shop

Filtros Ref.§: EF150 PNC: 900 168 3748

Technical line drawing of various electronic components including a coiled hose, plastic housing, and connector (no text or symbols)

BedPro™ MINI Ref.§: ZE125 PNC: 900 168 0819

Technical line drawing of various electronic components including a coiled cable, plastic housing, and connector (no text or symbols)