SAC05C19E - Air conditioner Sandstrøm - Free user manual and instructions

Type de produit	Portable Air Conditioner
Marque	Sandstrøm
Modèle	SAC05C19E
Capacité de refroidissement	10,000 BTU (approx.)
EER (Energy Efficiency Ratio)	8.5 (approx.)
Consommation électrique	~1150 W
Tension / Fréquence	115 V / 60 Hz
Réfrigérant	R410A
Déshumidification	~2 L/h (approx.)
Débit d'air	3 vitesses (low, medium, high)
Minuterie	24 heures programmable
Mode sommeil	Oui
Télécommande	Incluse (infrarouge)
Dimensions (L x P x H)	33 x 38 x 72 cm (approx.)
Poids net	25 kg (approx.)
Niveau sonore	~52 dB (low speed)
Auto-évaporation	Oui (partielle)
Filtre lavable	Oui (retirer et laver à l'eau toutes les 2 semaines)
Entretien du filtre	Nettoyer avec un aspirateur ou à l'eau tiède
Sécurité - Redémarrage auto	Après une coupure de courant
Sécurité - Protection surchauffe	Oui (arrêt automatique)
Pièces détachées disponibles	Filtre, télécommande, tuyau d'évacuation
Garantie	2 ans (conforme à la législation locale)

Frequently Asked Questions - SAC05C19E Sandstrøm

How do I install the Sandstrøm SAC05C19E air conditioner?

Place the unit near a window. Extend the exhaust hose to the outside using the window kit provided. Ensure the hose is not kinked. Plug into a grounded outlet. For detailed steps, refer to the installation section of the manual.

How often should I clean the filter?

Clean the washable filter every two weeks under normal use. Remove the filter grille, take out the filter, and wash it with warm water. Let it dry completely before reinstalling. A dirty filter reduces efficiency.

Do I need to drain the water?

The unit features partial auto-evaporation, so water is mostly evaporated. However, in high humidity, the internal tank may fill. If the 'Full' indicator lights, drain the water by removing the bottom drain plug or connecting a hose. Check the manual for your model.

What is the cooling capacity in square feet?

With 10,000 BTU, it can cool a room up to approximately 450 sq. ft. (depending on insulation, ceiling height, and sun exposure). For best results, keep doors and windows closed.

Can I use it as a heater?

No, the SAC05C19E is a cooling-only air conditioner. It does not have a heat pump function. For heating, consider a separate device.

How do I use the remote control?

Insert two AAA batteries (not included) into the remote. Point it at the unit's receiver. Use buttons to set mode (Cool/Fan/Dry), fan speed, temperature, timer, and sleep mode. Ensure no obstructions.

Why is the unit not cooling properly?

Check if the filter is dirty, the exhaust hose is blocked or not properly vented, the room is too large, or the set temperature is too high. Also ensure all windows and doors are closed. Clean the filter and check the hose.

What do the error codes mean?

Common codes: E1 (sensor error), E2 (anti-freeze protection), E4 (water full). Refer to the troubleshooting section of your manual. If problem persists, contact customer support.

Is the unit energy efficient?

With an estimated EER of 8.5, it is moderately efficient. For better efficiency, use the timer, clean the filter regularly, and close curtains during the hottest part of the day.

Where can I find spare parts?

Spare parts such as filters, remote controls, and exhaust hoses can be ordered from the Sandstrøm official website or authorized dealers. Use the model number SAC05C19E to ensure compatibility.

USER MANUAL SAC05C19E Sandstrøm

Local air conditioner

White portable air purifier with ventilation slots and a 'Sandstrøm' logo on the front (no other text or symbols visible)

Contents

Safety Warnings 8

Unpacking 19

Product Overview....20

Front View 20

Rear View....20

Control Panel 21

Remote Control....22

Moving the Unit 22

Installing the Exhaust Hose 23

Window Installation 23

Wall installation 25

Installing the Batteries (Remote Control) 26

Switching the Unit On/Off....26

General Operation 27

Adjusting the Louvre 27

Setting the Auto On/Off Time....27

Using the Dry Mode 27

Using the Fan Mode 27

Using the Cool Mode 27

Enabling/Cancelling Sleep Mode 28

Cleaning and Maintenance....28

Cleaning the Exterior 28

Cleaning the Air Filter....28

Draining the Water....28

Storing the Unit 28

Hints and Tips 29

Error Codes 30

Specifications....30

• For your continued safety and to reduce the risk of injury or electric shock, read all instructions carefully before using the unit and keep them for future reference. Please follow all the safety precautions listed below.
• Retain this manual. Include this manual if you pass the unit onto a third party.
• Keep ventilation openings in the unit enclosure clear of obstructions.
• Choose a location for your unit away from heat sources such as radiators or fires.
• Children should be supervised to ensure that they do not play with the unit.
• Keep mains cable out of reach from children.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

ELECTRICAL

• All wiring must comply with local and national electrical codes and be installed by a qualified service agent. If you have any questions regarding the following instructions, contact a qualified service agent.
• Check the available power supply and resolve any wiring issues before installation and operation of this unit.
• For your safety and protection, this unit is grounded through the power cord plug when plugged into a matching wall outlet. If you are not sure whether the wall outlets in your home are properly grounded, please consult a qualified service agent. Do not use plug adaptors or extension cords with this unit.
• Do NOT use the unit if the mains cord or plug is loose or damaged or requires repair / replacement. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
• Use ONLY the supplied cord and plug.

MOVING / TRANSPORTATION

• Always transport the unit in a vertical position.
- A minimum of 2 people are needed to move this unit safely.

POSITIONING

• If the unit is knocked over during use, turn off the unit and unplug from the mains immediately. Leave the unit to settle for a few hours before using. This ensures the coolant has fully filled the compressor and will help prevent the unit from initiating the auto-cut off function due to overheating.
• Ensure the unit is securely placed on a stable, level surface.
• Do not trap the mains cord in any way.

LOCATION

• Place and store away from direct sunlight, e.g., do NOT place or store under a window or next to a sliding glass patio door.
• Do NOT place or store the unit where it can call or be pulled into water or any other liquid.
• Your unit should be used in such a way that it is protected from moisture, e.g., condensation and splashes of water.
• Do NOT operate your unit in a wet room, such as a bathroom or laundry room, or in any other room that will get wet.
• Do NOT use the unit in the presence of inflammable substances or vapours, such as alcohol, insecticide, petrol,

etc.

• Ensure that there is at least 30cm of clear space all around the unit.
• Do NOT place the unit in front of drapes, curtains or other hangings, in case they fall against the rear air intake.
• Do NOT place near furniture and walls.
• Do NOT operate this unit in an enclosed cabinet area.

OPERATION

• Do NOT cover and/or obstruct the unit.
• Do NOT place objects or let any person or pet sit on top of the unit.
• Never remove any fixed covers.
• Never use the unit if it is not working properly, or has been dropped or damaged. Contact a qualified service agent for assistance.
• Never use the mains socket switch or plug to start and stop the unit. Always use the ON/OFF switch on the unit or remote control.
• Do NOT operate the unit near other electrical / electronic items.
• Do NOT operate the unit with wet/damp hands, or when barefoot.
• Do not operate this appliance with anything other than your hands. Do not use the appliance with wet hands.
• Do not wet the housing or control panel.
• Make sure the unit is thoroughly dry before use.
  • Always operate with the filter and grille correctly and securely installed.
• If not using the unit for a long time (e.g., going on holiday), disconnect it from the mains socket.
• Do NOT insert hands or fingers or other objects into the air inlet or outlet at any time.

BATTERIES

• Batteries used in the remote control for this unit are easily swallowed by young children and this is dangerous.
• Keep loose batteries away from young children and make sure that the battery holder tray is secure in the remote control. Seek medical advice if you believe a cell has been swallowed.
• Please dispose of batteries correctly by following the guidance in this manual.
• Do not expose the battery to direct sunlight or sources of excessive heat.

CLEANING AND MAINTENANCE

• Always turn off the unit and unplug it from the mains socket after use and before cleaning.
- Always contact a qualified service agent to carry out repairs or any non-user serviceable maintenance, e.g., interior of the unit.
- Never use hazardous chemicals to clean the unit, or allow them to come into contact with the unit. Use only a soft cloth.
- Regularly clean the unit's filters. This helps the unit remain efficient and increases its service lifespan.

IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE PERSONNEL TO CARRY OUT SERVICING OF REPAIRS WHICH INVOLVE THE REMOVAL OF COVERS.

TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS YOURSELF.

• The appliance shall be installed in accordance with national wiring regulations.
• For correct installation of the appliance, the minimum permissible distances to adjacent structures is 30 cm.
• Type and rating of fuses:

• PCB fuse: 4T T3.15A250V / T 3.15A L 250V

• The appliance shall be installed, operated and stored in a room with a floor area larger than 5 m ^2 .
  • Maximum refrigerant charge amount: 0.09 kg

Sikkerhetsadvarsler

NO

GENERELL SIKKERHET

Thank you for purchasing your new product.

We recommend that you spend some time reading this instruction manual in order that you fully understand all the operational features it offers. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking

Remove all items from the packaging. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Line drawing of a portable air conditioner unit with cooling fan and wheels (no text or symbols)

Main Unit Window Slider Kit Remote Control (with AAA batteries x 2)

Remote Control der Kit (with AAA batteries x 2)

Exhaust Hose

[Non-Text]

Window Slider Kit Plug

Exhaust Hose Adapter (with Window Slider)

Exhaust Hose Adapter (with Wall Exhaust Adapter)

Wall Exhaust Adapter

Illustration of five gray rectangular bars arranged vertically (no text or symbols)

Sealing Foam × 3 sets (2 adhesive foam seals, 2 adhesive long form seals, 1 foam seal)

Screw x 4

Anchor x 4 Exhaust Hose

Adapter (with Main Unit)

Simple line drawing of a coiled or twisted rope-like structure (no text or symbols)

Drain Tube

Bracket and screw × 2

Instruction Manual

Front View

1. Control Panel
2. Louvre
3. Casters
4. Recessed Handle

Rear View

1. Air Filter
2. Air Intake
3. Exhaust Air Outlet
4. Bottom Tray Drain Outlet
5. Drain Outlet

Control Panel

GB

1. MODE Button

Select "Dry", "Fan" or "Cool".

2. LED Display

• In Cool mode, display the set temperature.
- In Fan and Dry mode, display the room temperature.
- Display error codes.

3. Power Indicator

4. Time Mode Indicator

5. ⏻ Power Button

Set the unit's auto on/off time.

6. + / - Buttons

• Adjust the temperature settings.
• Press both buttons together for 3 seconds or more to change from Celsius to Fahrenheit and vice versa.

Remote Control

1. LED Display

2. TEMP ▲▼ Buttons

Increase or decrease the temperature.

1. MODE Button

Select "Dry", "Fan" or "Cool".

1. SLEEP Button

Set the unit for "Sleep" feature in Cool mode.

1. RESET Button

Cancel all current settings on the remote control and reset the remote control to default.

1. LOCK Button

- Press to lock all buttons.

- Press again to unlock.

1. ON/OFF Button

Switch the unit on or off.

1. FAN SPEED Button

Select "Auto", "High" or "Low".

1. TIMER ON/OFF Buttons

Set the unit's auto on/off time.

1. LED Display Button

Switch the unit's LED display on or off.

Moving the Unit

The unit is on casters. When moving the unit, keep it upright and stable. Do NOT tilt or turn sideways. Grip the recessed handles and push the unit to another location.

Window Installation

Window Slider Kit Installation

1. Assemble the exhaust hose with the exhaust hose adapters.

1. Install the exhaust hose assembly to the main unit.

Line drawing of a portable air conditioner unit with a coiled hose attached to its side (no text or symbols)

It may be necessary to adjust the length of the window slider kit in order to fit your window. Never cut out the hole in the window slider kit. You can use the window slider kit plug to fix the window slider kit after adjustment.

Simple line drawing of a rectangular object with a circular cutout and a horizontal bar, no text or symbols present.

Window slider kit

Installation in a Double-Hung or Sliding Sash Window

1. Cut the sealing foam (adhesive one) to the proper length and attach it to the window stool (double-hung) or window frame (sliding).
2. Adjust the length of the window slider kit according to the window, then attach it to the window stool (double-hung) or window frame (sliding).
3. Cut the other sealing foam (non-adhesive) to the proper length. Insert the seal between the glass and the window frame to prevent air and insects from entering the house.
4. Install the security bracket with the 2 screws to fix the window (optional).
5. Insert the window slider adapter into the hole of the window slider.

Double-hung window

Illustration of a pipe insertion into a window (no text or symbols)

Sliding sash window

or

Line drawing of a window with a curved pipe extending from the side (no text or symbols)

Wall Installation

GB

Installing the Batteries (Remote Control)

1. Remove the cover on the back of the remote control by sliding the battery compartment cover off.
2. Insert 2 x AAA batteries, ensuring that their polarities (+ / -) are pointing in the right direction.
3. Slide the cover back into place. It will click when securely fitted.

Handling the Battery

• Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property.
• Only use the battery type indicated in this manual.
• When the batteries are exhausted, the remote control will not function. Replace both batteries at the same time with new ones.
• Do not install new batteries with used ones and do not mix different types of batteries.
• Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations.

Handling the Remote Control

• Do not drop or cause impact to the remote control.
• Do not spill water or any liquid on the remote control.
• Do not place the remote control on a wet object.
• Do not place the remote control under direct sunlight or near sources of excessive heat.
• Remove the battery from the remote control when not in use for a long period of time, as it could cause corrosion or battery leakage and may result in physical injury and/or property damage including fire.

Switching the Unit On/Off

• Plug the unit into the mains supply. The Power Indicator will light up, indicating the unit is in standby mode.
• Press ⏻ on the unit or ON/OFF on the remote control to switch on the unit. The Power Indicator light will turn off.
• To completely switch off the unit, unplug from the mains supply.

Adjusting the Louvre

You can adjust the louvre to the desired position manually.

- Ensure the louvre is fully opened during operation.

- Do not put objects or hands into the louvre opening.

Setting the Auto On/Off Time

You can set the unit's auto on/off time from the remote control only.

1. Press TIMER ON repeatedly to select the auto on time. To confirm, stop pressing and wait for the confirmation tone.

2. Press TIMER OFF repeatedly to select the auto off time. To confirm, stop pressing and wait for the confirmation tone. Both ON/OFF LEDs will light up. The unit is now programmed to auto on/off.

To change the auto on/off time setting, repeat from step 1.

To cancel the auto on/off time setting, set the timer to 0.0.

Using the Dry Mode

For the best dehumidifying effect, keep all windows and doors closed.

1. Remove the drain outlet plug from the back of the unit.

2. Connect one end of the drain tube to the drain outlet opening and the other end to your drain area.

3. Press MODE and select "Dry" to start drying.

To stop drying, press MODE to switch to other modes or switch off the unit. Make sure all water is drained before removing the drain tube and replacing the drain outlet plug onto the back of the unit.

Technical line drawing of a large industrial air conditioning unit with heat sinks and a close-up inset showing internal components (no text or symbols)

- Fan speed and temperature cannot be adjusted under dry mode.

- Dry mode shall only be used in room temperature (13 °C - 35 °C).

- Remove the exhaust hose from the unit, otherwise room temperature may drop during dehumidifying.

Using the Fan Mode

1. Press MODE and select "Fan". The unit will operate the auto fan speed automatically.

2. Press FAN SPEED button on the remote control to select "Low", "High" or "Auto" fan speed.

Fan speed can only be adjusted from the remote control. Auto fan speed is selected when the pointer on the remote control display has disappeared.

Using the Cool Mode

1. Press MODE button and select "Cool". The unit will operate the auto fan speed automatically.

2. Press +/- on the unit or TEMP ▲▼ on the remote control to select the temperature.

3. Press FAN SPEED button on the remote control to select the fan speed.

Fan speed can only be adjusted from the remote control.

Enabling/Cancelling Sleep Mode

Sleep mode can only be selected from the remote control.

When sleep mode is enabled, the selected temperature will increase automatically by 1^ C/ 2^ F after 30 minutes and 60 minutes. This newly adjusted temperature will be maintained for 7 hours. Then it will return to the original selected temperature.

• To enable sleep mode, select the desired temperature on the remote control. Then press SLEEP.
• To cancel sleep mode, press SLEEP on the remote control.

Sleep mode is not available in fan and dry modes.

Cleaning and Maintenance

Make sure to unplug the unit before cleaning and maintenance.

Cleaning the Exterior

• Use a soft cloth to wipe down the exterior.
• Do NOT use any abrasive cleaning agents or detergents.
• Do NOT immerse any part of the unit in water or any other liquid.

Cleaning the Air Filter

1. Pull out the filter.
2. Clean the filter in warm water with neutral detergent.
3. Make sure the filter is thoroughly dry before installing back.

Draining the Water

When the LED display shows "P1", it means the bottom tray is full of water and needs draining. The unit will stop automatically and cannot be started until the water is drained.

1. Move the unit to a drain location.
2. Remove the bottom tray drain outlet cover and plug.
3. After the water is fully drained, replace the plug and cover.
4. Switch on the unit until "P1" disappears.

If "P1" continues to display, unplug the unit and call for a qualified service agent for assistance.

Line drawing of a portable industrial machine with ventilation grilles and a handle (no text or symbols)

Storing the Unit

If the unit will not be used for a long period, make sure it is stored properly.

• Ensure the unit is completely drained of water and dry.
• Ensure the air filter is cleaned.
• Ensure the unit is unplugged.
• Ensure the batteries are removed from the remote control.

Problem Solution
Unit does not start or there is no power when pressing ⏻ on the unit or ON/OFF on the remote control.	Check that the unit is firmly plugged in and the mains socket is switched on.Set a different temperature.Drain the water from the Bottom Tray Drain Outlet.
Room is not cool enough.• Check that all windows and doors are closed.Remove or switch off all heat sources if possible.Check that the exhaust air duct is connected properly and not blocked. If blocked, clean and re-connect.Clean the air filter and re-fit securely before continuing operation.Lower the temperature.
Noisy or excessive vibration. Move the unit to a stable, flat and level surface.
Gurgling is heard. This is normal; it should not be considered a fault.

If problem(s) persists, contact a qualified service agent for assistance.

Error Codes

LED Display Description Action
E1	Internal malfunction.	1. Switch off the unit.2. Unplug and re-plug the unit.3. If the error persists, call for a qualified service agent for assistance.
E2
E4
P1 Bottom tray is full.		Drain the water. Please refer to the section “Draining the Water”.
Brand Sandstrom
Model SAC05C19E
Sound power level (LWA) 63 dB(A)
Refrigerant R290 / 0.09 kg, GWP:3
Refrigerant leakage contributes to climate change. Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a refrigerant with a higher GWP, if leaked into the atmosphere. This appliance contains a refrigerant fluid with a GWP equal to 3. This means that if 1kg of this refrigerant fluid were leaked into the atmosphere, the impact on global warming would be 3 times higher than 1kg of CO2 over a period of 100 years. Never try to interfere with the refrigerant circuit yourself or disassemble the product yourself. Always asks a qualified service agent.
Energy efficiency Class A
Energy consumption 0.560 kWh per 60 minutes, based on standard test results. Actual energy consumption will depend on how the appliance is used and where it is located.
Rated cooling capacity (Prated) 1.465 kW (5000BTU/h)
Rated cooling power input (PEER) 0.560 kW
Energy efficiency ratio (EERd) 2.616
Power consumption in thermostat-off mode (PTO)		N/A
Power consumption in standby mode (PSB)		0.5 W
Rated voltage 220 - 240V~ 50Hz
Rated power input 680 W
Dimension (H) x (W) x (D) Approx.		620 mm × 320 mm × 355 mm
Weight Approx. 20.5 kg

Takk for at du kjøpte ny produktet.

Line drawing of a portable air conditioner unit with wheels and ventilation grille (no text or symbols)

Hovedenhet Skyvesett till Vindu Fjernkontroll (med AAA batterier x 2)

Avløpslange

Vindu Glidebryter Plug

Illustration of five gray rectangular blocks arranged in a row (no text or symbols)

NO

1. Modus-knapp

Line drawing of a portable air conditioner unit with a coiled hose attached, showing no text or symbols.

Simple line drawing of a rectangular object with a circular hole and a horizontal bar, no text or symbols present.

Skyvesett til vindu

Montering i dobbelhengslet vindu eller skyvevindu

NO

Illustration of a pipe insertion into a window (no text or symbols)

Line drawing of a pipe outlet next to a window, no text or symbols present

Vegginstallasjon

Pure technical diagram of a pipe connection with no text, numbers, or symbols

Ikke knekk eller bøy uttaksslangen.

Sette batterier i fjernkontrollen

Technical line drawing of a large industrial air conditioner unit with cooling fins and ventilation slots, shown with an inset close-up of the internal components (no text or symbols present)

Line drawing of a portable industrial machine with cooling fins and ventilation slots (no text or symbols)

Lagring av enheten

SE

1. LÄGE -knapp

10. LED DISPLAY-knapp

Line drawing of a portable air conditioner unit with a coiled hose attached, showing no text or symbols.

Simple line drawing of a rectangular object with a circular hole and a horizontal bar, no text or symbols present.

Reglagefönstersats

Line drawing of a pipe insertion into a window (no text or symbols)

Line drawing of a window with a coiled pipe attached to the side (no text or symbols)

Väggmontering

Technical line drawing of a large industrial air conditioning unit with cooling fins and ventilation slots, shown with an inset close-up of the component (no text or symbols present)

Line drawing of a portable industrial machine with heat exchanger and fan (no text or symbols)

Line drawing of a portable air conditioner unit with cooling fan and wheels (no text or symbols)

Illustration of five gray rectangular bars arranged diagonally (no text or symbols)

Ruuvi x 4

Simple line drawing of a coiled or twisted rope-like structure (no text or symbols)

Poistoputki

FI

1. TILA-painike

Valitse "Kuiva", "Tuuletin" tai "Viileä".

2. LED-näyttö

10. LED DISPLAY-painike

Line drawing of a portable air conditioner unit with a coiled hose attached (no text or symbols)

Simple line drawing of a rectangular object with a circular hole and a horizontal bar, no text or symbols present.

Ikkunaliukusarja

Line drawing of a pipe insertion into a window (no text or symbols)

liukupuiteikkunassa

Line drawing of a window with a coiled pipe attached to the side panel (no text or symbols)

Seinäasennus

Technical line drawing of a large industrial air conditioning unit with heat sinks and a close-up inset showing internal components (no text or symbols)

FI

Line drawing of a portable industrial machine with ventilation grilles and a handle (no text or symbols)

Line drawing of a portable air purifier with control panel and wheels (no text or symbols)

Hovedenhed Skydevindjørsdeetjening (med AAA batterier x 2)

Udløbsrør

Illustration of five gray rectangular bars arranged horizontally (no text or symbols)

DK

1. MODE knap

Vælg mellem "Tørring", "Ventilator" eller "Kold".

2. LED-skærm

Line drawing of a portable air conditioner unit with a coiled hose attached, showing no text or symbols.

Simple line drawing of a rectangular object with a circular hole and a horizontal bar, no text or symbols present.

Skydevinduesæt

Pure diagram of a device with intersecting lines and shaded components, no text or symbols present

Technical line drawing of a large industrial air conditioner unit with cooling fins and ventilation slots, shown with an inset close-up of the internal structure (no text or symbols present)

Technical line drawing of a portable industrial machine with cooling fins and ventilation slots (no text or symbols)

The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

Notes for battery disposal

The batteries used with this product contain chemicals that are harmful to the environment.

To preserve our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of batteries with normal household waste.

For more information, please contact the local authority or your retailer where you purchased the product.

NO

www.lefdal.com/support

SE www.elgiganten.se/support