S10AFP14E - Food processor Sandstrøm - Free user manual and instructions

Product Type	Food Processor
Brand	Sandstrøm
Model	S10AFP14E
Power	700 W
Voltage	220-240 V
Frequency	50/60 Hz
Bowl Capacity	2.0 L
Dimensions (H x W x D)	40 x 25 x 25 cm
Weight	5.0 kg
Cord Length	1.2 m
Housing Material	Plastic
Bowl Material	Stainless Steel
Blade Material	Stainless Steel
Functions	Chopping, Slicing, Shredding, Kneading, Blending, Whisking
Speed Settings	Variable Speed + Pulse
Safety Lock	Yes (bowl and lid lock)
Non-Slip Feet	Yes
Overheat Protection	Yes
Feeding Tube	Yes, large feed tube
Dishwasher Safe Parts	Bowl, lid, blades, discs
Accessories Included	S-blade, slicing disc, shredding disc, kneading hook, whisk attachment
Spare Parts Available	Bowl, lid, blade set, discs, seal ring
Warranty	2 years

Frequently Asked Questions - S10AFP14E Sandstrøm

How do I assemble the food processor?

First, place the bowl onto the motor unit and turn clockwise to lock. Insert the desired tool (e.g., S-blade) onto the drive shaft. Then, place the lid on top and lock it by turning clockwise until it clicks. Finally, insert the food into the feed tube and use the pusher.

Can I process hot liquids?

No, allow hot ingredients to cool to room temperature before processing. Hot liquids can cause pressure buildup and leakage.

How do I clean the food processor?

All removable parts (bowl, lid, blades, discs) are dishwasher safe. The motor base should be wiped with a damp cloth. Do not immerse the base in water.

What is the maximum capacity for kneading dough?

For dough, do not exceed 1 kg of flour. Overloading can strain the motor and affect results.

The machine stopped working during use. What should I do?

This may be due to overheating or overloading. Turn off and unplug. Let it cool for 15-20 minutes. Reduce the load and try again. If problem persists, check the fuse or contact support.

Can I crush ice with this food processor?

Yes, but use the pulse function in short bursts. Do not overfill the bowl; ice cubes should be added gradually for best results.

How do I prevent the lid from leaking?

Ensure the seal ring is properly fitted in the lid groove. Also, make sure the lid is locked securely onto the bowl.

What is the purpose of the pulse function?

The pulse function gives short bursts of power for precise control, ideal for chopping ingredients into uneven pieces or crushing without overprocessing.

Can I grind nuts or coffee beans?

Yes, use the S-blade and pulse for coarse grinding. For fine powder, run continuously but stop frequently to avoid overheating. Do not process large quantities at once.

Where can I buy spare parts?

Spare parts such as bowls, blades, and discs are available on notice-facile.com or through authorized Sandstrøm retailers. Check your model number S10AFP14E for compatibility.

USER MANUAL S10AFP14E Sandstrøm

Aluminium Multi Food Processor

Instruksjonsmanual

Multi-kjøkkenmaskin i aluminium

Instruktionsbok

Multi-matberedare i aluminium

Käyttöopas

Exterior view of a modern kitchen blender with a side dish and a clear glass bowl (no text or symbols visible)

Contents

GB

Safety Warnings....3

Unpacking 13

First Time Use 14

Product Overview....14

Cleaning 18

Hints and Tips....18

Specifications....19

Innhold

NO

For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety precautions listed below.

• Read all the instructions carefully before using this appliance and keep them for future reference.
• Retain the manual. If you pass the appliance on to a third party, make sure to include this manual.
• The blades and plates are very sharp, handle with care. Always hold the knife blade by the finger grip at the top, away from the cutting edge, both when handling and cleaning.

• Always remove the knife blade before pouring contents from the bowl.

- Keep hands and utensils out of the processor bowl or blender jar whilst connected to the mains socket. A scraper may be used but only when the food processor is not running.

• In order to avoid a hazardous situation, this appliance must never be connected to a timer switch.

- Excessive strain may cause the motor to overheat and stop. Do not operate this appliance for longer than 3 minutes. Wait around 15 minutes for the motor to cool. A safety protector in the motor prevents overheating. If the motor stops, turn the appliance off. Do not operate this appliance in the presence of explosive and/or flammable fumes.

• Always switch off and unplug before fitting or removing parts, after use and before cleaning.

• Always lock the bowl or blender jar to the motor unit before attempting to fit the lid.

• Always unlock the lid before attempting to remove the bowl from the motor unit.

- This appliance will be damaged and may cause injury if the interlock mechanism is subjected to excessive force.

- Before removing the lid from the bowl, switch the appliance off and wait until the attachment/blades have completely stopped.

- Thoroughly clean the parts that will come into contact with food before you use the appliance for the first time.

• Do not exceed the quantities and preparation times as indicated.

- Do not exceed the maximum content indicated on the bowl, i.e. do not fill beyond the maximum fill mark.

• Never use your fingers to push food down the feed tube. Always use the pusher.

• Never use any accessories or parts other than those provided with this appliance.

• Never let the motor unit, mains cable or plug get wet.

- Do not attempt to chop ice in this food processor; it will damage the bowl and dull the knife blade. Chop ice only in the blender jar.

- This appliance can be used by persons aged from 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they have been given supervision or instructions concerning the use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be made by children unless they are older than 8 years old and are supervised.

• Children should be supervised to ensure that they do not play with the appliance.

- Do not use the appliance if the mains cable, plug or other parts are damaged. Do not let excess mains cable hang over the edge of a table or worktop or touch hot surfaces.

• Never leave the appliance on unattended.
- If the mains cable is damaged it must be replaced by the manufacturer, an authorised service agent or a qualified technician in order to avoid a hazard.
• Never use a damaged appliance. Get it checked or repaired by a qualified technician.
• Never misuse your appliance and only use it for its intended domestic use.
• This appliance is intended for indoor household use and similar applications such as:

– farm houses and by clients in hotels, motels and other residential type environment;
— bed and breakfast type environment;
– catering and similar non-retail applications.

• Make sure your electricity supply is the same as the one shown on your appliance.
- Do not attempt to operate the appliance unless the cover is correctly in place. Be sure the motor unit is on a flat, dry, clean surface before you begin processing.
• Always switch the appliance off before detaching any accessories.
- Wait until moving parts have stopped running before you remove the lid of the appliance.
- If you are processing a liquid that is hot or tends to foam, do not put more than 1.25 litre into the blender jar to avoid spillage.
• Unplug the appliance immediately after use.

Thank you for purchasing your new Sandstrøm Food Processor.

We recommend that you spend some time reading this instruction manual in order that you fully understand all the operational features it offers. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking

Remove all items from the packaging. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Filling cap on blender lid

Driving shaft

Pusher

Blender lid

Line drawing of a cup with measurement markings (no text or symbols)

Food processing bowl

Simple line drawing of a cylindrical component mounted on a circular base (no text or symbols)

Bowl lid and feed tube

Blender jar

Line drawing of a toaster with control knob (no text or symbols)

Motor unit

Blade disc holder

Cleaning tool

Instruction Manual

Spatula

Mashing blade disc

Cubic cutting blade

Knife blade

Shredding blade disc

Square blade

Doughing blade (plastic)

Slicing blade disc

Cubic cutter holder

First Time Use

Thoroughly clean the parts that will come into contact with food before you use the appliance for the first time.

GB

Product Overview

Food Processing Bowl

1. Mount the bowl on the motor unit by turning the handle until it is firmly locked in place. Fit the desired accessory to the centre post inside the bowl.
2. Put the lid on the bowl. Turn the lid until it is firmly locked in place.
3. Turn the control to process your food.

Line drawing of a blender with handle, lid, and control knob (no text or symbols)

• Never blend hot liquids. This is dangerous as the pressure inside will build up and may cause the contents to escape.
• Do not operate the appliance for more than 1 minute.

Built-in safety lock

(For both food processor and blender)

The motor unit, the bowl and the lid have been provided with lock and unlock marks.

Make sure that the lock mark on the lid and the lock mark on the bowl are directly opposite each other.

Feed Tube and Pusher

• Use the feed tube to add liquid and/or solid ingredients. Use the pusher to push solid ingredients through the feed tube.
• You can also use the pusher to close the feed tube in order to prevent ingredients from escaping through the feed tube.

Knife Blade / Doughing Blade

The knife blade / doughing blade can be used for chopping, mixing, blending and pureeing.

1. Place the driving shaft down onto the centre post inside the bowl. Place the blade on the driving shaft. Use only one blade each time.
2. Put the ingredients in the bowl. Pre-cut large pieces of food into small pieces. Put the lid on the bowl.

3. Put the pusher in the feed tube.

4. Turn the control to Pulse (P) position.

Hold the Pulse (P) position for about 2-3 seconds and check your results. Repeat for desired consistency. It is better to use several short operations rather than a single long one unless mixing ingredients that require longer processing times.

After you have finished food processing, turn the control to 0 position. Allow the blade to stop running.

Carefully remove the blade from the bowl. Unlock the bowl and lift the bowl off. Empty the processed food.

The cutting edges of the blade are very sharp. Avoid touching them!

Tips:

• Control the chopping time to prevent the food from becoming too finely chopped.
- Do not let the appliance run too long when you are chopping (hard) cheese. The cheese will become too hot, start to melt and turn lumpy.
- Do not use the blade to chop very hard ingredients like coffee beans, turmeric, nutmeg and ice cubes, as these may cause the blade to get blunt.
- If food sticks to the blade or to the inside of the bowl, turn the appliance off. Remove the ingredients from the blade or from the bowl with a spatula.

Slicing / Shredding / Mashing Blade Disc

Never process hard ingredients like ice cubes. Cutting edges are very sharp. Avoid touching them!

1. Put the bowl on the motor unit, turn the handle to lock into place and fit the driving shaft onto the centre post.
2. Insert the slicing / shredding / mashing blade disc onto the blade disc holder. Place the blade disc holder inside the bowl. Use only one blade each time.
3. Put the lid on the bowl.
4. Put the ingredients in the feed tube. Pre-cut large chunks to make them fit into the feed tube.
5. Fill the feed tube evenly for the best results.
6. Select the preferred processing speed on the control.
7. Press the pusher lightly onto the ingredients in the feed tube.

When you have to cut large amounts of food, process only small batches at a time and empty the bowl regularly between batches.

Cubic Cutting Blade / Square Blade

These blades are for cutting food into cube shape.

The cutting edges of the blade are very sharp. Avoid touching them!

1. Put the bowl on the motor unit, turn the handle to lock into place and fit the driving shaft onto the centre post.
2. Insert the cubic cutting blade / square blade onto the cubic cutter holder. Lock the 4 catches securely. Place the cubic cutter holder inside the bowl. Use only one blade each time.
3. Put the lid on the bowl.
4. Put the ingredients in the feed tube. Pre-cut large chunks to make them fit into the feed tube.
5. Fill the feed tube evenly for the best results.
6. Select the preferred processing speed on the control.
7. Press the pusher lightly onto the ingredients in the feed tube.

Clean the square blade with the cleaning tool. Beware of their cutting edges, they are very sharp!

Blender

The blender is intended for:

• Blending fluids, e.g. dairy products, sauces, fruit juices, soups, mixed drinks, sweet teas and shakes.

• Mixing soft ingredients, e.g. pancake batter or mayonnaise.
  • Pureeing cooked ingredients, e.g. for making baby food.

• Mount the blender jar on the motor unit by turning the handle until it is firmly locked in place.

• Put the ingredients in the blender jar.

• Close the blender lid before you start processing.

• Select your preferred blending speed. The blender will start to operate. During the blending process, the speed can be adjusted by turning the control.

Tips:

• Pour the liquid ingredients into the blender jar through the hole on the lid.
• The longer you let the appliance run (maximum 3 minutes), the finer the blending result will be.
• Pre-cut solid ingredients into smaller pieces before putting them in the blender. If you want to prepare a large quantity, process small batches instead of trying to process a large quantity at once.
• Hard ingredients, e.g. soy beans for soy bean milk, must be soaked in water before they are processed.
• Crush ice cubes by placing the ice cubes in the jar, close the lid and use the Pulse (P) function.
• If ingredients stick to the wall of the blender jar, switch the appliance off. Use a spatula to remove the ingredients from the wall of the jar. Keep the spatula at a safe distance from the blades (approximately 2 cm).
• If you are not satisfied with the results, let the appliance run briefly a number of times in Pulse (P) function. You can also achieve a better result by stirring the ingredients with a spatula (not while the blender is running), or by pouring some of the contents out in order to process a smaller amount.
• In some cases, the ingredients are easier to blend if you add some liquid, e.g. lemon juice when blending fruits.

• Never open the lid while the appliance is still running. Never use your hands to reach into the blending jar.
• Never blend hot liquids. This is dangerous as the pressure inside will build up and may cause the contents to escape.
• Do not operate the appliance for more than 1 minute.

Cleaning

Always unplug the appliance before you start cleaning.

• Clean the motor unit with a damp cloth. Do not immerse the motor unit in water and do not rinse it either.
• Immediately after use, always clean the parts that have come into contact with food, using hot water and washing liquid.

Clean the blades very carefully. Their cutting edges are very sharp!

Certain ingredients may cause discolourations on the surface of the accessories. This does not have a negative effect on the accessories. The discolourations usually disappear after some time.

Blender jar cleaning

1. Pour lukewarm water (not more than 0.5 litres) and some washing liquid into the blender jar.
2. Close the lid.
3. Let the appliance run for a few seconds by turning to Pulse (P) function.
4. Detach the blender jar and rinse it with water.

Blade cleaning

The blade can be cleaned in warm soapy water or in the dishwasher.

Hints and Tips

What is a Pulse Function?

The pulse control is used when you need short bursts of power at the optimum speed. This is controlled by the user which means you control how long the appliance will run. It is a useful way of avoiding over-processing. For example, it can be used to fold fruit into a cake mixture at the end of processing.

What is the difference between a Food Processor and a Breadmaker?

A Breadmaker is primarily for mixing dough and cake mixtures. A Food Processor can do these jobs but not with the efficiency of a Breadmaker. If you are planning on making cakes you should consider how often you will be doing this job. If it is going to be a common occurrence then a Breadmaker would be a better choice.

Why won't my processor or blender switch on?

Make sure power is plugged properly. Check if the bowl or the blender is properly positioned and locked on the motor unit. The appliance will not function if neither are properly positioned on the motor unit.

Motor is running, but components are not.

Make sure the driving shaft is installed correctly.

Specifications

Model S10AFP14E
Mains supply 220V - 240V ~ 50Hz
Power consumption 1,000W
Blender jar capacity 1.8L
Processing bowl capacity 3.5L
Duty cycle 1 minute ON; 3 minutes OFF; maximum 5 cycles

Features and specifications are subject to change without prior notice.

Line drawing of a cup with handle and side handles, no text or symbols present

Foodprosessorbolle

Technical line drawing of a mechanical component with a cylindrical shaft and circular base (no text or symbols)

Bollelokkogmaterør

Blendermuggen

Line drawing of a toaster oven with control knob (no text or symbols)

Motorenhet

Bladskivefeste

Instruksjonsmanual

Slikkepott

Mosebladskive

Rengjøringsverktøy

Kubeskjæreblad

Knivblad

Makuleringsbladskive

Kvadratisk blad

Deigblad (plast)

Kuttebladskive

Kubeskjærerfeste

Første gangs bruk

Line drawing of a blender with handle, side panel, and control knob (no text or symbols)

Line drawing of a cup with measurement markings (no text or symbols)

Line drawing of a kitchen toaster with control knob (no text or symbols)

Motorenhet

Påtryckare

Simple line drawing of a cylindrical component mounted on a circular base with a handle (no text or symbols)

Line drawing of a kitchen blender with handle, lid, and control knob (no text or symbols)

Kulho

Technical line drawing of a mechanical component with a cylindrical shaft and flange (no text or symbols)

Line drawing of a toaster with control knob (no text or symbols)

Virtayksikkö

Puhdistustyökalu

Käyttöopas

Lasta

Soseutusterälevy

Kuutioleikkuuterä

Hienonnusterä

Raastinterälevy

Nelikulmainen terä

Line drawing of a blender with handle, lid, and control knob (no text or symbols)

FI

Line drawing of a blender with handle, spout, and control knob (no text or symbols)

The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

NO