FZR 5611-B - Lawn mower Fieldmann - Free user manual and instructions

Product Type	Petrol Lawn Mower
Brand	Fieldmann
Model	FZR 5611-B
Engine Type	4-stroke OHV, air-cooled
Displacement	196 cm³
Rated Power	3.5 kW (4.7 hp)
Engine Speed	2900 rpm
Starting System	Pull cord
Fuel Type	Unleaded petrol, min. 95 octane
Fuel Tank Capacity	1.0 L
Oil Type	SAE30 or 15W-40
Oil Capacity	0.6 L
Cutting Width	560 mm
Cutting Height Adjustment	Central, 6 positions, 25–75 mm
Grass Catcher Capacity	75 L
Mowing Functions	Grass collection, rear discharge, side discharge, mulching
Chassis Material	Steel
Wheel Size (Front/Rear)	200 mm / 280 mm
Weight	33.9 kg
Noise Level (Lwa)	98 dB(A)
Max Vibration Level	5.822 m/s² (K=1.5)
Maximum Slope	20°
Warranty	24 months

Frequently Asked Questions - FZR 5611-B Fieldmann

What type of oil should I use for the FZR 5611-B lawn mower?

Use SAE30 or 15W-40 motor oil. The oil capacity is approximately 600 ml. Always check the oil level before each use and keep it between the MIN and MAX marks on the dipstick.

How do I start the lawn mower?

First, ensure the fuel tank is filled with unleaded petrol (95 octane) and the oil level is correct. If the engine is cold, press the fuel primer bulb 2-3 times. Then pull the start/brake lever toward the handle and hold it, then pull the starter rope. The engine should start after 3-4 pulls. Release the start/brake lever to stop.

What should I do if the engine won't start?

Check the following: fuel tank empty? Fill with fresh fuel. Spark plug loose or dirty? Tighten to 25-30 Nm or replace. Ignition cable disconnected? Reattach. Air filter dirty? Clean it. Also ensure the choke is in the correct position.

How often should I change the engine oil?

Change the oil after the first 5 hours of operation, then every 25 hours thereafter. Use SAE30 or 15W-40 oil. Drain the oil from the plug under the engine, refill with fresh oil, and check the level.

Can I mow on slopes with this mower?

Yes, but do not use the mower on slopes steeper than 20°. Mow across the slope (parallel to contours), not up and down. Proceed carefully to avoid engine seizure.

How do I adjust the cutting height?

Use the central mowing height adjustment lever (Fig. 1, point 10). You can select one of 6 positions ranging from 25 mm to 75 mm. For most lawns, the middle height is suitable. Avoid the lowest setting to prevent lawn damage.

How do I replace the mowing blade?

Stop the engine and disconnect the spark plug. Remove the bolt securing the blade (Fig. 10). Install the new blade with the correct orientation and tighten the bolt to 40 Nm. We recommend contacting an authorized service center for this task.

What type of fuel should I use?

Use unleaded petrol with an octane rating of at least 95 (Natural 95). Do not use fuel with alcohol or ethanol additives as they can damage the fuel system. Always use fresh, clean fuel.

How do I store the mower for a long period?

Drain the fuel tank and run the engine until it stops to empty the carburetor. Remove the spark plug, pour a small amount of oil into the cylinder, and pull the starter cord 2-3 times. Clean the exterior and store in a dry place. For storage over 30 days, always drain fuel.

What does the grass catcher full indicator look like?

The grass catcher has a plastic flap at the rear. When the catcher is not full, the flap is raised. When it closes (drops down), it indicates the catcher is full and needs to be emptied.

USER MANUAL FZR 5611-B Fieldmann

Abstract black and white spiral pattern with no text or symbols

FIELDMANN®

Home & Garden Performance

Black and white photo of a FELVIN lawn mower on a flat surface (no visible text or symbols)

FZR 5611 B

English 3-22

Čeština....23-42

Slovenština....43 - 62

Magyarul....63 - 80

Polski 81-104

Petrol Lawnmower USER'S MANUAL

Thank you for purchasing this rotary petrol lawnmower. Before you start using it, please, carefully read this user's manual and save it for possible future use.

TABLE OF CONTENTS

1. GENERAL SAFETY INSTRUCTIONS....4
   Important safety notice....4
   Packaging 4
   User's Manual....4
2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE....5
3. DESCRIPTION OF THE LAWNMOWER....7
4. ASSEMBLY/PREPARATION....7
   Taking the lawnmower out of the cardboard packaging 7
5. ASSEMBLING THE LAWNMOWER 8
6. BEFORE STARTING THE LAWNMOWER 9
   Adding oil....9
   Adding fuel....9
7. CONTROLLING AND OPERATING THE LAWNMOWER.... 10
   Starting the lawnmower 10
   Controlling travel....11
   Application range for the lawnmower....11
   Mowing with the grass catcher 11
   Mowing with rear discharge 11
   Mowing with side discharge 11
   Mulching....12
   Setting the mowing height....12
   Replacing the mowing blades 12
   Changing the motor oil 12
8. SAFETY INSTRUCTIONS....13
   General safety instructions 13
   Instructions for use 13
9. MAINTENANCE....14
   Lawn care....14
   Maintenance 15
   Service....16
   Warranty does not cover 16
   Storage 16
10. TECHNICAL SPECIFICATIONS 17
11. REGULAR MAINTENANCE SCHEDULE.... 18
12. DETECTION AND TROUBLESHOOTING 19
13. DECLARATION OF CONFORMITY 20
14. DISPOSAL 21

1. GENERAL SAFETY INSTRUCTIONS

IMPORTANT SAFETY NOTICE

Carefully unpack the product and take care not to throw away any part of the packaging before you find all the parts of the product.
Store the machine in a dry place out of reach of children.
Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical shock, a fire and/or serious injuries.

PACKAGING

The product is packed in a package that prevents damage during transport. This package is a resource and so can be handed over for recycling.

USER'S MANUAL

Before you start working with the machine, read the following safety and usage instructions.

Acquaint yourself with the operating elements and the correct use of the machine. Keep the user's manual in a safe place where it can be easily retrieved for future use. Save the original packaging, including the internal packing material, warranty card and proof of purchase receipt at least for the duration of the warranty.

If you need to ship this machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport (e.g. when moving or when you need to send this product for repair).

Note: If you hand over the machine to somebody else, do so together with the user's manual. Following the instructions in the included user's manual is a prerequisite for the proper use of the machine. The user's manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not following the instructions in this manual.

2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE

Before putting into operation, please carefully read the user's manual.

Keep other persons away from the work area.

Attention, rotating blades! Protect yourself against the danger of injury to limbs.

Emission of toxic gasses. Do not use the petrol lawnmower in enclosed or unventilated areas.

Hot surfaces, risk of burns!

Before carrying out maintenance, turn off the engine and disconnect the spark plug.

Never add fuel while the engine is running.

Indicates that there is a risk of injury to persons, death or damage to the machine if instructions are not followed

Use hearing protection. Use eye protection. Use breathing organ protection.

Always maintain a distance from moving parts.

Travel along the slope on contours, not up and down.

Conforms to all relevant European directives.

Petrol is extremely fl ammable and therefore allow the engine to cool down for 2 minutes before adding more fuel.

3. DESCRIPTION OF THE LAWNMOWER

1. Travel lever
2. Start / brake lever
3. Top part of the handle
4. Quick-release screws
5. Bottom part of the handle
6. Air filter cover
7. Fuel primer bulb – Primer
8. Side discharge defl ector
9. Cap with oil dipstick
10. Mowing height adjustment lever
11. Grass catcher
12. Grass catcher cover
13. Handle panel

4. ASSEMBLY/PREPARATION

Before assembling and starting the petrol lawnmower, first carefully read the entire user's manual and the instructions contained in it.

IMPORTANT INFORMATION: The lawnmower is supplied WITHOUT FUEL AND OIL in the engine. Your new lawnmower was tested at the production plant meaning that a small amount of residual oil may be in the engine.

TAKING THE LAWNMOWER OUT OF THE CARDBOARD PACKAGING

Take the lawnmower out of the cardboard packaging and check that no loose parts are left in the packaging.

5. ASSEMBLING THE LAWNMOWER

IMPORTANT INFORMATION: Carefully unfold the lawnmower handle, being careful not to pinch or damage the lawnmower's control cables.

1. ASSEMBLING THE HANDLE

1. Insert the bottom part of the handle (Fig. 2 – point 1) into the respective holes on the lawnmower (see arrow) and secure in place with screw and nut.
2. Adjust the handle height for the lower installation according to the selected position, Pic. 2b.
3. Attach the top part of the handle (Fig. 2a - point 2) to the bottom part of the handle using the included screws with the quick coupler and wing nuts (Fig. 2c).

Fig. 2b

Close-up of a metal clip holding a black handle against a white background (no text or symbols visible)

Fig. 2c

Diagram of a mechanical device with multiple curved rods extending from a base, labeled 'Fig. 2c' (no text or symbols on the diagram itself)

2. INSTALLING THE HANDLE PANEL

Attach the plastic handle panel using the included screws (fi g. 3).

Mechanical assembly diagram showing a bracket with arrows indicating force or movement (no text or symbols present)

3. ASSEMBLING THE GRASS CATCHER

Secure the plastic hooks at the end of the textile part of the grass catcher into the steel frame (fi g. 4).

Two black plastic bins with a curved arrow indicating rotation, shown from different angles (no text or symbols)

IMPORTANT NOTICE: The grass catcher is equipped with a full indicator. It is a plastic flap at the rear of the grass catcher. When the grass catcher is not full, the flap is raised. When it closes, it is necessary to tip out the grass catcher.

6. BEFORE STARTING THE LAWNMOWER

ADDING OIL

The lawnmower is supplied without motor oil. Before first start up, add motor oil SAE30 or 15W-40 (approx 600 ml) according to the following instructions.

1. When pouring in the oil, place the lawnmower on a level surface.
2. Pull the cap with the oil dipstick out of the oil refill hole (Fig. 5).
3. After adding oil, put the dipstick back into the hole and tighten it.
4. The oil level must be between the upper (MAX) and lower (MIN) limit (Fig. 5).

Caution! DO NOT OVERFILL the oil tank, otherwise a large amount of smoke will come out of the exhaust when the lawnmower is started up.
IMPORTANT INFORMATION: Check the oil level before every use of the lawnmower. Add oil if necessary. Add oil up to the MAX level mark on the oil dipstick.
IMPORTANT INFORMATION: Replace the oil after the first 5 hours of operation and subsequently after every 25 hours of operation.

ADDING FUEL

The suitable type of fuel for this engine is NATURAL 95

After unscrewing the fuel tank cap, add the fuel, pouring it in all the way up to the collar of the fuel tank but do not overfi ll it.

Always add fresh, clean and approved lead-free petrol with an octane rating of at least 95.

Caution! In the event that you spill any oil or fuel on the lawnmower when refilling, wipe it away immediately. Do not store or add fuel or handle it in any way in the vicinity of an open fire.

Caution! Fuels mixed with alcohol or fuels with ethanol or methane additives may bind moisture to themselves, which may result in separation during storage and the formation of acids. Subsequently during storage the acid vapours may damage the fuel system of the lawnmower engine. These fuels must not be used in the lawnmower.

IMPORTANT INFORMATION: When not using the lawnmower for longer than 30 days, drain the fuel tank, start the engine and let it run until the fuel lines and the carburettor are empty (the engine will stop on its own). This will prevent future engine problems. Before using it again, add fresh fuel into the fuel tank.

7. CONTROLLING AND OPERATING THE LAWNMOWER

STARTING THE LAWNMOWER

1. If the engine is not warmed up, press the fuel primer bulb 2-3 times (Fig. 6 – point 1). If the engine is already warm, it is not necessary to use the fuel primer bulb.
2. Pull the start/brake lever towards the handle and hold it there (Fig. 6 – point 2), then pull on the pull cord (Fig. 6 – point 3). The engine should start up after 3-4 pulls.
3. The engine is turned off by releasing the start/brake lever.

Fig. 6

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Caution! A small amount of smoke may be emitted when the engine is started up for the first time as the protective layers in the engine are burnt off. This is completely normal and does not constitute a problem.

CONTROLLING TRAVEL

The travel is controlled using the travel lever (Fig. 7 – point 1). When the lever is pulled to the handle, the lawnmower will start moving.

To stop, release the lever. This lawnmower has one constant speed.

Illustration of two hands performing a cable clamp or adjustment technique, showing step 1 and final view (no text or symbols)

APPLICATION RANGE FOR THE LAWNMOWER

Mowing with collection of grass clippings in a grass catcher

Mowing with rear discharge of grass clippings

Mowing with side discharge

Mulching - mowing with loose placement of grass clippings on the lawn

Caution! Do not use the mower on slopes with an inclination of more than 20^ , otherwise motor seizure might occur!

MOWING WITH THE GRASS CATCHER

When the grass catcher is installed, grass clippings are discharged into the grass catcher.

Caution! In case of poor mown grass catching, increase the mowing height and check if the lawn is wet.

MOWING WITH REAR DISCHARGE

Without the grass catcher installed, the grass catcher cover serves as a defl ector that directs the movement of the grass clippings towards the ground. A row of grass clippings is thereby formed behind the lawnmower.

MOWING WITH SIDE DISCHARGE

Caution! Attach and remove the side discharge deflector only with the engine turned off.

Use your hand to lift the side discharge cover and attach the side discharge deflector (fi g. 8). In order to mow with side discharge, it is necessary to install a mulching plug into the discharge chute.

Close-up of a black plastic car seat component being held, with hands adjusting the part (no visible text or symbols)

PETROL LAWNMOWER USER'S MANUAL

MULCHING

Caution! Attach and remove the mulching plug only with the engine turned off.

Caution! Use only original mulching accessories when mulching.

1. Remove the grass catcher and hold the plastic grass catcher cover with your hand (Fig. 9 – point 1).
2. Install the mulching plug into the discharge chute (Fig. 9 – point 2) and make sure that the plug is seated firmly.

IMPORTANT INFORMATION: Do not mulch tall grass all at once, this will prevent overloading the lawnmower mechanism and the engine.

Fig. 9

SETTING THE MOWING HEIGHT

The mowing height is set centrally using the central mowing height adjustment lever (Fig. 1 – point 10). You can select in the range of 25 to – 75 mm. The middle mowing height is the most suitable for the majority of lawns. Lawn damage may result when the lowest height is set.

Caution! For maximum effectiveness, please always trim the grass by 1/3 of its length only. Mow the overgrown grass gradually and after each mowing, lower the height by one step. To keep quality lawn, do not use the lowest mowing height setting.

REPLACING THE MOWING BLADES

Caution! For this task, we recommend that you contact an authorised service centre.

If you wish to replace the mowing blade, remove the bolt (Fig. 10). Perform the installation according to the provided picture. Tighten the screw. The tightening torque is 40 Nm . When replacing the blade, replace the fastening bolt also.

Technical line drawing of a mechanical bracket assembly with mounting flange and bolted base (no text or symbols)

CHANGING THE MOTOR OIL

Caution! For this task, we recommend that you contact an authorised service centre.

The drain plug is located under the engine (Fig. 11 – point 1). Place a suitable container for catching the used oil under the engine and remove the plug. Tilt the lawnmower so that all the oil can drain from the oil tank.

After draining the oil, put the plug back into the hole, making sure that the plug is securely in its place and wipe away any drops of spilled oil.

Add type SAE30 or 15W-40 oil into the oil tank.

When the oil dipstick is inserted into the hole and screwed in, the oil level should be between the Min and Max marks (Fig. 11). Do not overfill the oil tank.

Start the engine and allow it to run for a short time.

Stop the engine, wait 1 minute and remeasure the oil level in the oil tank. Add oil to the required level if necessary.

Fig. 11

8. SAFETY INSTRUCTIONS

GENERAL SAFETY INSTRUCTIONS

This product is used exclusively for mowing grass. Do not use it for any other purposes than those intended. Otherwise there is a risk of damaging it or an injury.
* Never allow children or persons who are not acquainted with the contents of this user's manual to work with the machine.
The person operating the lawnmower is responsible for the safety of persons in the work area.

Never operate the lawnmower in the near vicinity of other people, children or freely roaming animals.

Before starting mowing, check the terrain where the lawnmower will be used and remove stones, wires, sticks, splinters, bones and other foreign objects, which could become caught in it or deflected or cause injuries.

INSTRUCTIONS FOR USE

All nuts, pins and bolts must be properly tightened so that the machine is in a safe and operational condition.
* Never use the lawnmower without the grass catcher or protective cover.
Never use the lawnmower with loose mowing blades. Always check in advance that all respective bolts are securely tightened. Blunt blades must be sharpened evenly.

Damaged blades must be replaced.

When working with the lawnmower, wear long pants and solid footwear.
* Never start the lawnmower in enclosed or poorly ventilated areas where fumes could accumulate. Emissions from the engine contain carbon monoxide, which is life threatening.
* Work only during suffi cient light conditions (in daylight or suffi cient artifi cial lighting).
Do not use the lawnmower when it is raining or if the grass is wet.
Proceed especially carefully when mowing in elevated terrain (on a slope). Always mow perpendicular to the slope, parallel to the contour, and not directly up/down.
Under no condition leave the lawnmower running without supervision; if you leave the lawnmower, turn off the engine.

Never lift the rear part of the lawnmower when starting it and always keep your limbs away from the cutting deck or the rear grass ejection chute while the engine is running.
* Never modify the engine's speed setting.
On lawnmowers with travel, release the travel lever before starting the engine.
Never transport the lawnmower while its engine is running.
Stop the engine and disconnect the spark plug in the following cases:

• when performing any task whatsoever under the mowing deck or in the rear grass ejection chute.
• when performing maintenance, repairs or inspecting the machine.
• before carrying, lifting or transporting the lawnmower.
• when you leave the lawnmower without supervision or you are getting ready to adjust the mowing height.
• before removing and emptying the grass catcher.
• when an impact with a foreign object occurs, stop the engine and carefully inspect to ensure that there is no damage. In the event of damage, take the lawnmower to a specialised service centre for repairs.

ATTENTION: The mowing blade continues to rotate for several seconds after the engine is turned off.

• if the lawnmower is vibrating abnormally (immediately identify and remedy the cause of the vibration).
• For the purpose of ensuring safe operation, regularly check that the pins, bolts and nuts on the lawnmower are securely tightened.

ATTENTION: FUEL IS A VERY FLAMMABLE LIQUID.

Store fuel in a suitable container.
Only add fuel in an open and well ventilated location. When handling fuel, do not smoke or use a mobile phone.
Only add fuel when the engine is turned off. Never open the fuel tank or add fuel if the engine is hot or if it is running.
If fuel is spilled, do not start the engine. Take the lawnmower away from the location where the fuel was spilled and take care to avoid possible ignition. Continue with work only after the spilled fuel has evaporated and the fuel fumes have dissipated;
After adding fuel, securely tighten the fuel tank cap and the cap on the fuel canister.

ATTENTION: Before carrying out maintenance or repairs, stop the engine and disconnect the spark plug.

9. MAINTENANCE

LAWN CARE

* Various forms of care are required depending on the type of grass area.
Therefore, always read the instructions included on seed packages with respect to the mowing height for the growing conditions in the given locality.
It is necessary to always keep in mind that the larger part of grass consists of a stem and one or more leaves. When the leaves are cut off completely, the lawn is damaged and the renewal of growth will be much more difficult.

The following instructions generally apply:

– excessively low mowing causes disruption to the roots and subsequently "spotty" appearance;
– in summer, mowing must be higher to prevent the soil from drying out;
- mowing wet grass may result in a lower efficiency of the blade due to grass catching on the blade and grass being ripped out of the ground;
- in the event of exceptionally tall grass it is appropriate to perform the first mow at the maximum permitted mowing height of the machine and then mow again only after two or three days.

The lawn will have a better appearance when it is mowed regularly over its entire area at the same height with alternating mowing directions.

MAINTENANCE

Caution! Always tilt the mower towards the handle side only (rear of the mower).

* All nuts, pins and bolts must be properly tightened so that the machine is in a safe and operational condition. Regular maintenance is the basic prerequisite for ensuring safety of the user, maintain the lawnmower's operating condition and high performance.
* Never store a machine with petrol in the fuel tank inside a building where the fumes could come within range of an open fire, sparks or sources of high temperature
Before storing in any enclosed area, allow the engine to cool down.
To reduce the risk of a fire, ensure that the lawnmower and in particular the engine, exhaust muffler, battery and also the location of spare fuel storage are free of grass, leaves or excessive amounts of lubricant.
* Regularly inspect the condition of the deflector and the grass catcher; replace if damaged.
Drain the fuel in a well ventilated area when the engine has cooled down.
When removing or installing the mowing blade, use thick work gloves.
It is necessary to check the balance of the mowing blade every time that it is sharpened.

⚠️ ATTENTION: Before carrying out maintenance or repairs, stop the engine and disconnect the spark plug.

* Regularly inspect the lawnmower and ensure that all grass deposits are removed from the underside of the chassis.
* Regularly lubricate the axle of the chassis and the bearings using a suitable lubricant.
* Regularly inspect the condition of the blades because they have a signifi cant effect on the performance of the lawnmower. Blades should always be sharp and balanced.
In regular intervals, check that all nuts and bolts are tightened. Nuts and bolts that are worn out or incorrectly tightened may cause serious damage to the engine or the frame.
If the blade strongly impacts an obstacle, stop the lawnmower and take it to an authorised service centre.
* BLADE: the blade is made from pressed steel. To achieve the best possible mowing results, regularly sharpen the blades, approximately after every 25 hours of operation. Check that the blade is always correctly balanced. To do this, insert a steel axle (with a diameter of 2-3 mm) into the middle hole. If it is correctly levelled, the axis will remain in the horizontal position.
If the blade does not remain in the horizontal position, replace it.
When removing the blade, screw out the bolt, check the load bearing part of the blade. If the parts are worn out or damaged, replace them.

ATTENTION: Always use only original spare parts. Poor quality spare parts may cause serious damage to the lawnmower and create a safety hazard.

SERVICE

In the event that after purchasing the product you find any kind of defect, contact the service department. When using the product, follow the instructions contained in the included user's manual.
A complaint will not be accepted if you modified the product or if you did not follow the instructions in the user's manual.

WARRANTY DOES NOT COVER

Normal wear and tear of operating parts of the machine as a result of its use
Servicing tasks related to standard maintenance of the machine (e.g. cleaning, lubrication, tuning, etc.). Defects caused by external effects (e.g. climatic conditions, dustiness, inappropriate use, etc.)
Mechanical damage resulting from the machine being dropped, impact, etc.
* Damages resulting from unprofessional handling, overloading, use of incorrect parts, inappropriate tools, etc.
On returned products that were not properly protected against mechanical damage during transport, the risk of potential damage is borne exclusively by the owner.

STORAGE

If you will not be using the machine for an extended period of time, store it according to the following instructions. This will extend the lifetime of the machine.
* Fully drain fuel from the fuel tank and the carburettor.
Screw out the spark plug and pour a small amount of motor oil into the socket. Gently pull the pull cord 2 to 3 times.
Use a clean cloth to clean the exterior surfaces. Store the machine in a clean dry location.

10. TECHNICAL SPECIFICATIONS

Engine XP200
Engine type OHV, air cooled, 4-stroke
Rated power 3.5 kW
Engine rpm 2900 rpm
Displacement 196 cm	^3
Starting Pull cord
Fuel tank volume 1.0 litres
Recommended fuel Petrol - lead-free, at least 95 octane
Oil tank volume 0.6 l
Recommended oil	SAE30, 15W-40
Mowing height adjustment	Central, 6 positions
Adjustable mowing height range	25-75 mm
Mowing coverage	560 mm
Wheel size	Front 200 mm, rear 280 mm
Grass catcher capacity	75 l
Chassis	steel
Declared noise level	98 dB (A)
Maximum vibration level	5.822 m/s (K=1.5)
Weight	33.9 kg

Amendments to text and technical parameters are reserved.

Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make such changes.

11. REGULAR MAINTENANCE SCHEDULE

Always carry out the regular maintenance schedule at a monthly or hourly interval – whichever comes first		Before each use	After 5 hours of operation for new machines	Every 6 months or after 25 hours of operation	Every year
Cleaning the machine, tightening the connecting screws		X
Engine oil	Level check X
	Replacement		X		X
Air filter	Inspection X
	Cleaning			X
	Replacement				X
Spark plug	Inspecting & Cleaning X
	Replacement				X
Checking the mowing mechanism	Inspection X(*)
Idling Checking & Adjusting X(*)
Valve movement Checking & Adjusting X(*)
Combustion chamber Cleaning X(*)
Fuel lines	Inspecting & Cleaning				X(*)
General preventative inspection					X(*)

*entrust this maintenance to an authorized service centre

Caution! If the mower is used in arduous or dusty conditions, change the oil and clean the air filter at more frequent intervals

12. DETECTION AND TROUBLESHOOTING

Problem Probable cause Procedures
Unable to start the engine	Choke valve damper in wrong position Move	the choke lever to the correct position
	The fuel tank is empty Fill the fuel tank with fuel
	The air fi lter is dirty Clean the air fi lter
	Loose spark plug Tighten the spark plug to 25-30 Nm
	The ignition cable is loose or disconnected from the spark plug	Install the ignition cable to the spark plug
	Incorrect gap between spark plug electrodes	Install a new spark plug with the correct gap between the electrodes
	Faulty ignition module Contact the repair shop
The engine is diffi cult to start or loses power	Dirt, water or old fuel in the tank	Drain the fuel and clean the tank. Fill the tank with fresh clean fuel
	Clogged air vent in fuel tank cap Clean or replace the fuel fi lter cap
	The air fi lter is dirty Clean the air fi lter
	Dirt, water or old fuel in the tank	Drain the fuel and clean the tank. Fill the tank with fresh clean fuel
	Clogged air vent in fuel tank cap Clean or replace the fuel fi lter cap
	The air fi lter is dirty Clean the air fi lter
The engine runs irregularly	Faulty spark plug	Install a new spark plug with the correct gap between the electrodes
	Incorrect gap between the electrodes	Set the gap between the electrodes to 0.7 - 0.8 mm
	The air fi lter is dirty Clean the air fi lter
The engine is idling poorly	The air fi lter is dirty Clean the air fi lter
	The air gaps in the engine cover are clogged	Remove debris from the gaps
	The cooling fi ns and air passages below the engine fan are clogged	Remove debris from cooling fi ns and air passages
The engine stops at high speed	The gap between the spark plugs is too small	Set a gap of 0.7 to 0.8 mm
The motor is overheating	Limited airflow	Remove any debris from the gaps on the engine cover, fan cover, and air passages
	Unsuitable spark plug	Install a new spark plug with the correct gap between the electrodes
The mower vibrates violently	The cutting unit is loose Tighten the mower blade
	The cutting unit is not balanced	The mower blade must be balanced
	Bent crankshaft	Contact the repair shop

FAST®

FAST ČR, a.s.

Černokostelecké 1621, 251 01 Šičany, Czech Republic

tel: [phone], fax: [phone]

Declaration of Conformity

Product/ brand: Gasoline powered lawnmower/ FIELDMANN

Type/ model: FZR 5611-B

196cm ^3 ; 3,5kW/2900 min ^-1 , Cutting width 560mm, Lpa 78dB(A), Lwa 98dB(A)

Manufacturer: FAST ČR, a.s.

Černokostelecká 2111, 100 00 Praha 10, Czech Republic

VAT no: CZ26726548

This declaration of conformity is issued under the sole responsibility of the manufacturer.

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

Directive Machinery 2006/42/EC

Directive EMC 2014/30/EU

Directive Noise 2000/14/EC + 2005/88/EC

Directive Emission of gaseous 2016/1628/EU

Directive RoHS 2015/863/EU

The relevant harmonised standards and the other technical specifications:

EN ISO 5395-1:2013+A1

EN ISO 5395-2:2013+A1+A2

EN ISO 14982:2009

EN ISO 3744:1995

ISO 11094:1991

CE

Place of issuance: Prague

Name: Ing. Zdeněk Pech

Chairman of the Board

Date of issuance: 20.8.2019

Signature:

FAST

FAST CR, a.s.

Černokostelecka 1621, 251 01 Áčany

IČO: 26726548 tel.: [phone]

DIC: CZ2672654B fax: [phone]

100-26 7265 AR, DIC-07-26 7265 AR

Dispose of used packaging material at a site designated for waste in your municipality.

The machine and its accessories are manufactured from various materials, e.g. metal and plastic.

Take damaged parts to a recycling centre. Inquire at the relevant government department.

This product meets all the basic requirements of EU directives that apply to it.

Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make these changes.

Translation of the original user's manual.

Close-up of a metal clamp tool attached to a black cylindrical rod (no text or symbols visible)

Diagram of a mechanical device with multiple blades and a base, labeled 'Obr. 2c' (no other text or symbols)

2. INSTALACE PANELU MADLA

Mechanical assembly diagram showing a bracket with arrows indicating force or movement (no text or symbols)

3. SESTAVENI KOŠE

Two black plastic bins with a curved arrow indicating rotation, shown from different angles (no text or symbols)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Close-up of a black plastic car cover being held, with hands adjusting the lid (no visible text or symbols)

MULČOVÁNÍ

VÝMĚNA ŽACÍCH NOŽŮ

Technical line drawing of a mechanical bracket assembly with mounting flange and bolted base (no text or symbols)

VÝMĚNA MOTOROVÉHO OLEJE

Obr. 11

8. BEZPEČNOSTNÍ POKYNY

VŠEOBECNÉ BEZPEČNOSTNÍ POKYNY

Directive Machinery 2006/42/EC

Directive EMC 2014/30/EU

Directive Noise 2000/14/EC + 2005/88/EC

Directive Emission of gaseous 2016/1628/EU

Directive RoHS 2015/863/EU

a normami:

EN ISO 5395-1:2013+A1

EN ISO 5395-2:2013+A1+A2

EN ISO 14982:2009

EN ISO 3744:1995

ISO 11094:1991

CE

Vydáno v: Praze

Chairman of the Board

Udržujte ostatné osoby mimo pracovnej oblasti.

Close-up of a metal clamp tool attached to a black cylindrical rod (no text or symbols visible)

Diagram of a mechanical device with multiple blades and a base, labeled 'Obr. 2c' (no other text or symbols)

2. INŠTALÁCIA PANELU DRŽADLA

Mechanical component assembly with arrows indicating force or movement (no text or symbols)

3. ZOSTAVENIE KOŠA

Two black plastic bins with a curved arrow indicating rotation, shown from different angles (no text or symbols)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Close-up of a black plastic car cover being held, with hands adjusting the lid (no visible text or symbols)

MULČOVANIE

NASTAVENIE VÝŠKY KOSENIA

Technical line drawing of a mechanical component with no visible text or symbols

VÝMENA MOTOROVÉHO OLEJA

Obr. 11

8. BEZPEČNOSTNÉ POKYNY

VŠEOBECNÉ BEZPEČNOSTNÉ POKYNY

Directive Machinery 2006/42/EC

Directive EMC 2014/30/EU

Directive Noise 2000/14/EC + 2005/88/EC

Directive Emission of gaseous 2016/1628/EU

Directive RoHS 2015/863/EU

a normami:

EN ISO 5395-1:2013+A1

EN ISO 5395-2:2013+A1+A2

EN ISO 14982:2009

EN ISO 3744:1995

ISO 11094:1991

CE

Vydáno v: Prahe

Meno: Ing. Zdeněk Pech

Chairman of the Board

Close-up of a black and white plastic tool with a handle, attached to a vertical rod (no text or symbols visible)

2. A FOGANTYÚ-PANEL FELSZERELÉSE

Mechanical assembly diagram showing a bracket with arrows indicating force or movement (no text or symbols present)

Two black plastic bins with a curved arrow indicating rotation, labeled '4. ábra' (no other text or symbols)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Close-up of two black plastic car cover cases with hands holding them, no visible text or symbols

MULCSOZÁS

8. BIZTONSÁGI UTASÍTÁSOK

ÁLTALÁNOS BIZTONSÁGI ELŐÍRÁSOK

Close-up of a metal clamp tool attached to a black cylindrical rod (no text or symbols visible)

Diagram of a mechanical device with multiple blades and a base, labeled 'Rys. 2c' (no other text or symbols)

2. INSTALACJA PANELU UCHWYTU

Mechanical assembly diagram showing a bracket with arrows indicating force or movement (no text or symbols)

3. ZAKŁADANIE KOSZA

Two black plastic containers with a curved arrow indicating a change or motion, labeled 'Rys. 4' (no text on the containers themselves)

Illustration of hands performing a rope knotting technique (no text or symbols)

Illustration of a hand holding a tool with an arrow indicating motion, no text or symbols present

Close-up of hands holding a black plastic car cover component, no visible text or symbols on the object itself

SPALINOWA KOSIARKA DO TRAWY INSTRUKCJA OBSŁUGI

MULCZOWANIE

Technical line drawing of a mechanical bracket assembly with mounting flange and bolted base (no text or symbols)

WYMIANA OLEJU SILNIKOWEGO

Rys. 11

8. WSKAZÓWKI BEZPIECZEŃSTWA

OGÓLNE WSKAZÓWKI BEZPIECZEŃSTWA

1. WYKRYWANIE I USUWANIE PROBLEMÓW

Home & Garden Performance

Model /Modell /Modelis:

Conditions of guarantee

This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty is limited to the following conditions. Warranty is referred only to the customer goods using for common domestic use. The claim for service can be applied either at dealer's shop where the product was bought, or at below mentioned authorized service shops. The end-user is obligated to set up a claim immediately when the defects appeared but only till the end of warranty period. The end-user is obligated to cooperate to certify the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted. In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim application till the date of taking overthe product by end-user, or the date the end-user is obligated to take it over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed following documents: receipt, certificate of warranty, certificate of installation... This warranty is void especially if apply as follows: ■ Defects which were put on sale. ■ Wear-out or damage caused by common use. ■ The product was damaged by unprofessional or wrong installation, used in contrary to the applicable instruction manual, used in contrary to legal enactment and common process of use or used for another purpose which has been designed for. ■ The product was damaged by uncared-for or insufficient maintenance. ■ The product was damaged by dirt, accident of force majeure (natural disaster, fire, flood, ...). ■ Defects on functionality caused by low duality of signal, electromagnetic field interference etc. ■ The product was mechanically damaged (e.g. broken button, fall...). ■ Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable working conditions (e.g. high temperatures, high humidity, quakes,...). ■ Repair, modification or other failure action to the product by unauthorized person ■ End-user did not prove enough his right to claim (time and place of purchase). ■ Data on presented documents differs from data on products. ■ Cases when the claiming product can not be identified according to the presented documents (e.g. the serial number or the warranty seal has been damaged).

[e-mail]

www.fastcr.cz

Fast Plus, a. s.

Na Pántoch 18

SK 831 06 Bratislava

Slovenská republika

Tel.: [phone]

Fax: [phone]

[e-mail]

www.fastplus.sk

Jótállási jegy

[e-mail]

www.fasthungary.hu

Black and white photo of a lawn mower with open lid, no visible text or symbols

FIELDMANN®

Home & Garden Performance