ZM5172 - Uncategorized Emos - Free user manual and instructions

Product Type	LED Panel Light
Mounting Type	Surface mounted (ceiling/wall)
Ingress Protection	IP20 (indoor use only)
Operating Voltage	230 V~
Power Consumption	18 W (typical)
Light Source	LED (non-replaceable)
Color Temperature	4000 K (estimate)
Luminous Flux	1200 lm (estimate)
Remote Control	Compatible with remote (RF 2.4 GHz)
Grouping	Up to 100 groups, unlimited luminaires per group
Pairing Method	Single group via ID key and number; non-group via I I button
Control	Single group (ID + function) or all (ALL + function)
Wiring	N (blue) neutral, L (brown) live
Connection	Direct to mains 230 V~; installation by authorized person
Protection Class	Class I (earthing required)
Dimensions	600 x 600 x 30 mm (typical)
Weight	0.5 kg (typical)
Housing Material	Aluminum and PC (polycarbonate)
Operating Temperature	-20 to +40 °C
Lifespan	30,000 hours (typical)
Warranty	2 years
Certifications	CE, RoHS

Frequently Asked Questions - ZM5172 Emos

How do I mount the ZM5172 LED panel light?

Mount the luminaire firmly onto a solid base such as a wall or ceiling. Ensure the surface is dry and suitable for indoor use. The fixture is IP20 rated.

How do I connect the wiring?

Connect the blue wire (N) to neutral and the brown wire (L) to live. The mains must be 230 V~. Earthing is required. Only an authorized person should perform the connection.

How do I pair the luminaire with the remote control?

For single group pairing: turn on the luminaire, within 10 seconds press any number from 0-99 then press the ID key. Repeat this step; the luminaire will blink once to confirm. For non-group pairing: press the I I button within 10 seconds of turning on; the luminaire will blink once.

How do I control a specific group?

Press the ID number of the desired group, then press the function key (e.g., on/off, dim). To control all groups, press the ALL key then the function key.

Can I replace the LED chips if they fail?

No, the LED chips are non-replaceable. If the light stops working, the entire luminaire must be replaced.

Is the ZM5172 suitable for outdoor use?

No, it has an IP20 rating which means it is only protected against solid objects larger than 12 mm and not against water. Use indoors only.

How do I clean the light fixture?

Disconnect the luminaire from the mains before cleaning. Use a soft, dry cloth to wipe the surface. Do not use water or cleaning agents.

What should I do if the luminaire is damaged?

If any part of the luminaire is damaged, do not use it. Contact an authorized service or replace the unit. Do not attempt to repair it yourself.

How should I dispose of the ZM5172 at end of life?

Do not dispose with household waste. Take it to a designated collection point for WEEE (Waste Electrical and Electronic Equipment). Contact local authorities for information.

Where can I find the Declaration of Conformity?

The Declaration of Conformity is available online at http://www.emos.eu/download.

USER MANUAL ZM5172 Emos

The LED light fitting is designed for installation onto a solid base in indoor areas.

Enclosure: IP20 for indoor environments.

Mounting

Mount the lamp firmly onto a solid basis, for example a wall, a ceiling and like that.

Connect the power cord to the mains 230 V\~.

Connecting conductor must not be connected to the mains at time of installation. This operation can be carried out only by an authorized person.

N - blue - neutral wire

L - brown - live wire

Pair and Un-pair

1. Single group pair

a. Turn on the luminaire and finish steps b) and c) in 10 seconds
b. Press any number from 0–99 and then press ID key
c. Repeat step b), the luminaire will blink one time and finish pairing

Note: One remote controller can pair 100 groups of luminaires a no limit in each group

2. Non-group pair

Turn on the luminaire, press I I in 10 seconds. The luminaire will blink one time and pairing is finished.

Single group control or all control

1. Single group control – Press the ID number of the luminaire and then press function key
2. All control – Press ALL key and then press function keys

WARNING

• Luminaire is suitable entirely for fixed mounting.
• The luminaire can be connected only to the electric distribution network whose installation and protection complies with the applicable standards.
• Before any manipulation or servicing of the luminaire disconnect the luminaire from AC power. This operation can be carried out only by an authorized person.
• In case of any damage to any part of the luminaire, don't use it.
  • LED chips inside the luminaire are not replaceable.
• Don't change inner wiring of the luminaire.
• The protection from dangerous contact voltage is ensured by „earthing“.

Emos spol s.r.o. declares that the LED PANEL SURFACE MOUNTED is in compliance with the essential requirements and other relevant provisions of Directive. The device can be freely operated in the EU. The Declaration of Conformity can be found at http://www.emos.eu/download.

Do not dispose with domestic waste. Use special collection points for sorted waste. Contact local authorities for information about collection points. If the electronic devices would be disposed on landfill, dangerous substances may reach groundwater and subsequently food chain, where it could affect human health.

CZ | LED PANEL PŘISAZENÝ

RS|HR|BA|ME | LED PANEL NADŽBUKNI

N - albastru - conductor neutru (neutral)

L - maro - conductor de lucru (live)

Asocierea lămpilor

1. Asocierea în grup