CM12 - Loudspeaker Citronic - Free user manual and instructions

Product Type	Stage Wedge Monitor (Passive)
Model	CM12
Main Driver	300 mm (12") Coaxial
HF Driver	44 mm (1.75") Titanium Compression Driver
Frequency Response	55 Hz – 20 kHz
Impedance	8 Ω
Power Handling (RMS)	300 W
Power Handling (Max)	600 W
Sensitivity	96 dB
Dimensions (W x H x D)	355 x 350 x 275 mm
Weight	10.50 kg
Power Supply	External amplifier required (passive)
Input Connectors	2 x SPK (1+/1-, parallel)
Mounting Options	Floor wedge or 35 mm pole mount
Enclosure Material	Wooden cabinet with mesh grille
Care & Cleaning	Use soft dry cloth; avoid solvents
Safety	No user-serviceable parts; refer to qualified personnel
Spare Parts & Repairability	Not user-serviceable; contact retailer for service
General Information	Designed for live stage monitoring; coaxial driver for full-range output

Frequently Asked Questions - CM12 Citronic

What is the difference between the CM10, CM12, and CM15 models?

The CM10, CM12, and CM15 differ in driver size (10", 12", 15"), power handling, frequency response, sensitivity, and weight. For example, the CM12 has a 12" coaxial driver, 300W RMS, frequency response 55 Hz–20 kHz, sensitivity 96 dB, and weighs 10.50 kg (passive).

Can the CM12 be used as a PA speaker?

Yes, the CM12 can be pole-mounted on a 35 mm speaker stand or wall bracket for use as a PA speaker. It also works as a floor wedge for stage monitoring.

How do I connect the passive CM12 to an amplifier?

Use either of the two SPK input sockets (wired 1+/1-, pins 2 not connected). Connect one socket to the amplifier. The other socket can be used to daisy-chain another passive speaker. Ensure the amplifier can handle 8 Ω or 4 Ω if two speakers are connected.

What is the impedance of the CM12 passive speaker?

The CM12 passive speaker has an impedance of 8 Ω.

How should I clean the CM12 speaker cabinet?

Use a soft, dry or slightly damp cloth to clean the surfaces. A soft brush can remove debris from controls and connections. Do not use solvents as they may damage the cabinet.

What safety precautions should I take with the CM12?

Avoid exposing the unit to rain or moisture. Do not try to open or repair the speaker yourself; it contains no user-serviceable parts. Refer servicing to qualified personnel. For active models, ensure proper earthing and correct mains voltage.

What is the frequency response of the CM12?

The CM12 has a frequency response of 55 Hz – 20 kHz.

Can I use the CM12 for both floor monitoring and as a main PA?

Yes, the wedge shape allows floor monitoring, and the 35 mm pole socket enables mounting on a stand for PA use. The coaxial driver provides full-range output from a compact cabinet.

Does the CM12 have a built-in amplifier?

No, the CM12 is a passive speaker and requires an external amplifier. The active version (CM12A) has a built-in amplifier and DSP.

What is the warranty coverage for the CM12?

Damage caused by misuse is not covered. The product contains no user-serviceable parts; tampering invalidates the warranty. Keep the original packaging and proof of purchase for any replacement or return issues.

USER MANUAL CM12 Citronic

Stage Wedge Monitors

Item ref: CM10A 178.690UK

CM12A 178.692UK

CM15A 178.695UK

CM10 178.691UK

CM12 178.693UK

CM15 178.696UK

User Manual

Black audio amplifier speaker with mesh grille and control buttons (no visible text or symbols)

Black audio amplifier device with visible sound waves and internal components (no text or symbols)

Version 1.1

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

Introduction

Thank you for choosing a Citronic CM-series stage wedge monitor. These units are available in passive and active versions and can be positioned free-standing or pole-mounted via the 35mm socket. Please read this manual to achieve optimum performance from your speaker cabinet and avoid damage through misuse.

Package Contents

• CM-series stage wedge monitor
- Mains lead (active models only)

If you find any part is missing or the product has arrived with any problems, please contact your retailer at once. This product contains no user-serviceable parts, so make no attempt to try to fix or modify this item yourself as this will invalidate the warranty. We recommend you keep the original package and proof of purchase for any possible replacement or return issues.

Please note below for active models

Warning

To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture. Avoid impact to any of the components. No user serviceable parts inside - refer servicing to qualified service personnel.

Safety

- Please observe the following warning conventions

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

• Ensure that the correct mains lead is used with adequate current rating and mains voltage is as stated on the unit
• Avoid ingress of water or particles into any part of the housing. If liquids are spilled on the cabinet, stop using immediately, allow the unit to dry out and have checked by qualified personnel before further use

Warning: this unit must be earthed

Placement

• Keep the electronic parts out of direct sunlight and away from heat sources.
• Position the cabinet on a stable surface or stand that is adequate to support the weight of the product.
• Allow adequate space for cooling and access to controls and connections at the rear of the cabinet.
• Keep the cabinet away from damp or dusty environments.

Cleaning

• Use a soft dry or slightly damp cloth to clean surfaces of the cabinet
- A soft brush can be used to clear debris from controls and connections without damaging them
• To avoid damage, do not use solvents to clean any parts of the cabinet.

Passive panel layout

Both SPK input sockets are wired to 1+/1- in parallel

Active panel layout

1. DSP setting indicator LEDs
2. LINE A input combo Jack/XLR
3. Bluetooth on/off & pairing button
4. DSP rotary selector
5. Bluetooth & Amplifier status LEDs
6. MASTER volume control
7. HEADPHONE output volume control
8. Power on/off switch
9. LINE A input RCA (L+R)
10. MIX line output XLR
11. MIC/LINE B input combo Jack/XLR
12. Input B MIC/LINE level selector
13. MIC/LINE B volume control
14. HEADPHONE 6.3mm stereo output
15. LINE A volume control
16. IEC mains inlet & fuse holder

Setting up

For live stage monitoring, position your CM-series stage wedge on the floor facing upward toward the listener. The wedge can also be mounted onto a 35mm∅ speaker stand or wall bracket for use as a PA speaker. The coaxial main driver has an integral tweeter for full-range output from a focused, compact cabinet.

Passive models are connected via either of the two SPK input sockets, wired 1+/1- (pins 2 not connected). Connect to only one of these from the amplifier (another passive speaker may be connected to the other) Ensure that the CM passive monitor can handle the power from the amplifier at 8Ω (or 4Ω if 2 are connected).

Active models have 2 independent inputs...

Input A (2, 9) can accept a line level signal from a mixer, audio source or electronic instrument. The volume level of input A is controlled by the VOLUME A rotary control (15).

Input B (11) is switchable to accept either a microphone directly or a line input via the MIC/LINE button (12). The volume level of input B is controlled by the VOLUME B rotary control (13).

The overall output level of the monitor is governed by the MASTER volume control (6).

The mix of Input A and Input B (and Bluetooth as described below) can be output to further active speakers or monitors from the MIX OUT XLR connector (10).

A stereo HEADPHONE output (14) enables personal headphone monitoring, governed by a volume control (7).

Operation

When all signal connections are made, turn down the MASTER volume and connect to mains using the supplied IEC lead to the mains inlet (16). Switch on the power and a green POWER LED (5) will light. Turn up the MASTER control gradually, checking input signal(s) and gradually adjusting the VOLUME A and VOLUME B controls until the required volume is reached.

Corresponding to the output signal are a SIG (signal) and CLIP LED. The green SIG LED should be lit when sound is being produced and the CLIP LED may light very briefly on the loudest transients (beats) of the signal. If the red CLIP LED lights anything more than very briefly on each peak of the sound, the volume needs to be reduced to avoid overload and distortion of the output.

For wireless connection from a smart phone, the input section has a Bluetooth on/off and pairing button (3). Press this button to switch on the Bluetooth receiver, which will automatically connect to a previously paired smart phone and allow playback through channel A of the monitor. A blue LED (5) will light to confirm this.

To pair a smartphone with the CM-series active monitor, press and hold the Bluetooth button (3), which will cause the blue LED to flash, indicating pairing. Open the Bluetooth menu on the smart phone and search for a Bluetooth ID corresponding to the model number (e.g. CM10A) of the wedge monitor. Select and accept to pair to the CM monitor and the blue LED will stay lit constantly to confirm the pairing.

CM-series active monitors have an inbuilt DSP which has 5 optimal settings for different types of input or audio program material: Normal / DJ / Voice / Live / Flat. Although quite self-explanatory, it is worth experimenting with each profile to find the ideal EQ and tone response for each application. Simply turn the DSP rotary selector (4) and the DSP setting indicator LEDs (1) show which setting is active.

Specifications

Model	CM10/CM10A	CM12/CM12A	CM15/CM15A
Power supply (active)	230Vac, 50Hz (IEC)
Main driver	250mm∅ (10") coaxial	300mm∅ (12") coaxial	380mm∅ (15") coaxial
HF driver	44mm∅ (1.75") Ti compression driver
Frequency response	65Hz – 20kHz	55Hz – 20kHz	45Hz – 20kHz
Impedance (active / passive)	4Ω / 8Ω
Power: rms	250W	300W	350W
Power: max.	500W	600W	700W
Sensitivity	95dB	96dB	97dB
DSP settings (active)	Normal, DJ, Voice, Live, Flat
Dimensions	355 x 350 x 275mm	355 x 350 x 275mm
Weight (active / passive)	9.87kg / 8.64kg	12.10kg / 10.50kg	15.00kg / 13.10kg

Disposal: The "Crossed Wheelie Bin" symbol on the product means that the product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.

Hereby, AVSL Group Ltd. declares that the radio equipment type 178.690UK is in compliance with Directive 2014/53/EU

The full text of the EU declaration of conformity is available at the following internet address: http://www.avsl.com/assets/exportdoc/1/7/178690UK%20CE.pdf