VK85SVG - Uncategorized Cylinda - Free user manual and instructions

Brand	Cylinda
Model	VK85SVG
Product Type	Wine Cooler (Single/Dual Zone)
Power Supply	AC 220-240 V, 50 Hz
Required Fuse	10 A
Climate Classes	SN, N, ST, T
Temperature Range	Adjustable (default 12°C for single zone; upper 8°C, lower 12°C for dual zone)
Display	LED, shows current and set temperature
Interior Light	LED, adjustable intensity
Humidity System	Water reservoir, manual refill
Special Modes	Silent, Dynamic Cooling, Weekend
Temperature Alarm	Audible and visual when temperature deviates ±5°C
Shelves	Removable, adjustable
Door	Glass door with seal
Defrost	Automatic (no manual defrost needed)
Installation	Free-standing or built-in (ventilation required)
Dimensions (W x D x H)	595 x 575 x 820-890 mm
Spare Parts Availability	Minimum 7-10 years (depending on part)
Warranty	As per warranty card (minimum period stated in warranty)

Frequently Asked Questions - VK85SVG Cylinda

How do I turn the wine cooler on and off?

Press and hold the power button (①) for one second to turn on, or for five seconds to turn off. For complete disconnection, unplug from the mains.

How do I set the temperature?

Press the + or - buttons until the desired temperature flashes on the display. The set temperature will flash for five seconds before confirming.

What does the 'E1' or 'E2' error mean?

This indicates a temperature sensor failure. Contact the service center for repair.

How do I activate Weekend mode?

Press and hold both the power and light buttons simultaneously for five seconds. The indicator will flash four times. Mode automatically deactivates after 48 hours.

How do I clean the wine cooler?

Unplug the appliance. Clean the exterior and door seal with mild soapy water. Interior: use a solution of bicarbonate of soda and lukewarm water. Shelves: hand wash only, do not put in dishwasher.

Why is the wine cooler noisy?

Some noise is normal due to cooling gas circulation and the fan (even when compressor is off). Ensure the appliance is level and stable.

How do I change the temperature unit between °C and °F?

Touch and hold + for five seconds to enter settings mode. Use + and - to switch between °C and °F, then press the power button to confirm.

Does the wine cooler have a humidity control?

Yes, it includes a humidity reservoir that you fill with water (about 3/4 full) and place on the top shelf. Check and refill regularly.

What should I do if the door does not close properly?

Check that the appliance is level, the door seal is clean, and shelves are correctly positioned. If the door was removed, ensure it was refitted correctly.

How long is the warranty?

The warranty period is stated on the warranty card provided with the product. The manufacturer also guarantees spare parts availability for at least 7-10 years.

USER MANUAL VK85SVG Cylinda

Simple grayscale icon depicting a kitchen setup with a chimney, oven, and washing machine (no text or symbols)

VK85SVG

EN- Table of contents

GUIDELINES CONCERNING THE SAFETY OF USE 6 INSTALLATION AND OPERATING CONDITIONS OF THE APPLIANCE 8

CLIMATE RANGE 9

PRACTICAL EVERYDAY TIPS 10

UNPACKING 11

DISPOSAL OF OLD APPLIANCE 12

CONTROLS 13

APPLIANCE CONTROLS- SINGLE AND DUAL ZONE 13

TO SWITCH THE POWER ON/OFF 13

TO CHANGE THE TEMPERATURE 13

OPTIMAL TEMPERATURE SELECTION 14

INDOOR LIGHTING 14

SETTINGS MODE 14

SET THE TEMPERATURE UNIT °F OR °C. 14

SET THE DISPLAY BACKLIGHT INTENSITY 14

SET THE APPLIANCE INTERIOR LIGHTING INTENSITY. 14

SET SOUNDS. 14

INTERNAL HUMIDITY 14

TEMPERATURE DISPLAY 15

SILENT MODE 15

DYNAMIC COOLING MODE 15

WEEKEND MODE 15

TEMPERATURE ALARM 15

CARE AND CLEANING 16

REMOVING THE SHELVES 16

CLEANING 16

TROUBLESHOOTING 16

IF THE APPLIANCE IS NOT WORKING, CHECK 16

THE APPLIANCE IS WORKING, BUT NOT VERY WELL, CHECK 17

THE APPLIANCE IS NOISY, CHECK 17

THE LIGHT DOES NOT WORK, CHECK 17

THE DOOR WILL NOT CLOSE PROPERLY, CHECK 17

THE DISPLAY SHOWS "E1" OR "E2" 17

EPREL 17

WARRANTY AND AFTER SALES SERVICE 18

WARRANTY 18

SV- INNEHÅLLSFÖRTECKNING

SÄKERHETSANVISNINGAR 20 INSTALLATION OCH FÖRUTSÄTTNINGAR FÖR ANVÄNDNING 22

TILLÅTET TEMPERATUROMRÅDE 23

PRAKTISKA TIPS I VARDAGEN 23 UPPACKNING 25

SKROTA PRODUKTEN 25 REGLAGE 26

DISPLAYEN VISAR "E1" ELLER "E2" 30

EPREL 30

GARANTI OCH SERVICE 31

GARANTI 31

Dear customer,

From now on, your daily housework will be easier than ever before. Your appliance Cis exceptionally easy to use and extremely efficient. After reading these Operating Instructions, operating the appliance will be easy.

Before being packaged and leaving the manufacturer, the appliance was thoroughly checked with regard to safety and functionality.

Before using the appliance, please carefully read these Operating Instructions. By following these instructions carefully you will be able to avoid any problems in using the appliance. It is important to keep these Operating Instructions and store them in a safe place so that they can be consulted at any time.

Follow these instructions carefully in order to avoid possible accidents.

Sincerely,

Cylinda

GUIDELINES CONCERNING THE SAFETY OF USE

• The appliance is intended for household use only.
• The manufacturer reserves the right to introduce changes which do not affect the operation of the appliance.
• The Manufacturer shall not be held liable for damage arising from the failure to observe the instructions contained in this manual.
• Keep this manual for future reference, or to pass it over to the next user.
• This appliance is not intended for use by persons (including children) with limited physical or mental capabilities and persons who lack experience or familiarity with the appliance.
• Do not allow children to use the appliance. Do not allow them to play with the appliance. They must not climb inside the drawers and swing on the doors.
• The appliance operates properly at the ambient temperature (see product fiche). Do not use it in the cellar, unheated summer cottage during autumn and winter.
• When placing, moving, lifting the appliance, do not hold the door handles, do not pull the condenser at the rear part of the refrigerator and do not touch the compressor unit.
• Pull the plug out from the mains socket before each maintenance activity. Do not pull on the cord, but hold the body of the plug instead.
• The “cracking” sound, which the appliance may emit is caused by the expansion and contraction of parts as a result of temperature variations.
• For safety reasons do not repair the appliance yourself. Repairs carried out by persons who do not have the required qualifications may result in serious danger for the user of the appliance.

- Make sure you do not damage the cooling system, by puncturing the refrigerant pipes in the evaporator or breaking the pipes. The refrigerant is flammable. If the refrigerant makes contact with the eyes, rinse them with clean water and call for medical assistance immediately.

- Important! If the power cord is damaged, it should be replaced by the manufacturer or specialist repair centre or a qualified person in order to avoid danger.

- When performing activities, such as cleaning, maintenance or moving, the appliance must be completely disconnected from power supply (by pulling the plug out from the socket)

- This appliance can be used by children aged 8 years and older or by persons with physical, mental or sensory handicaps, or by those who are inexperienced or unfamiliar with the appliance, provided they are supervised or have been instructed how to safely use the appliance and are familiar with risks associated with the use of the appliance. Ensure that children do not play with the appliance. Cleaning and maintenance of the appliance should not be performed by children unless they are 8 years or older and are supervised by a competent person.

- Do not clean the appliance with steam

- Keep the appliance and its power cord away from children under 8 years old.

- Do not immerse the power cord or plug in water.

- Keep cord away from heated surfaces.

- Do not allow the connection cord hanging over the edge of a table or counter.

- Do not use any electrical appliances inside the chamber

- Do not use any tools to speed up the defrosting process

- Regularly clean the ventilation openings (in case of built-in appliances or those installed under the worktop)

• This appliance is not designed to be controlled by electronic timers or other devices that cut off power directly or remotely.
• In case of accidental spillage of liquids on electrical components, immediately unplug your appliance from the power supply.
• Make sure that the power cord is not crushed or damaged during installation.
• Disable the appliance before disposing of it. Unplug the appliance from the power supply and cut off the power cord. To prevent children or animals from being trapped in the appliance, remove the doors, hinges and locks.
• Note: If the appliance does not have a freezer compartment ( ^ ^** ), it is not suitable for freezing foodstuffs.
• Pursuant to Commission Regulation (EU) 2019/2019, the minimum availability period for spare parts necessary to repair the appliance is 7 or 10 years depending on the type and purpose of the spare part.
• The list of spare parts and the ordering procedure are available on the websites of the manufacturer, importer or an authorized representative.

INSTALLATION AND OPER- ATING CONDITIONS OF THE APPLIANCE

• Connect the appliance to the power supply 24 hours after unpacking and setting in the final location.
  • Take the product out of the package, remove the scotch tape protecting the door and the equipment. Any remaining adhesive stains may be removed with a mild washing agent.
• Clean the interior surface of the cooler and the elements of the equipment with a washing agent dissolved in lukewarm water, then wipe it dry.
• Place the cooler on an even, flat and stable surface, in dry, aired and shaded room, far from the heat sources such as: oven, hob, central heating radiators, central heating pipes, hot water installation, etc.
• On the exterior surface of the product may be a protective foil, this foils should be removed.

• Make sure the appliance is placed in a horizontal position by screwing in the 2 adjustable front legs (fig. 1)

• Keep free space on the sides and rear of the appliance (see installation drawing)

• When you install your wine cooler inside a furniture cabinet, make sure that the ventilation grille located in the bottom of the appliance is not blocked.
• Odours may be released when you first start your appliance. It will dissipate when the interior of the appliance cools down
• When you first start your wine cooler, the compressor will run continuously until the desired temperature is reached inside the chamber
• When you unplug your appliance from the power supply, it is recommended to wait 5 minutes before you plug it back in. This will reduce the risk of damage to the compressor.
• On selected models, the correct temperature will be shown on the display only a few hours after the wine cooler has been put into operation
• This appliance should be connected to AC 220-240V 50Hz supply socket. The socket must be fitted properly, and must be supplied with an earthing conduit and a 10A fuse.
• It is a legal requirement that the appliance is properly earthed. The manufacturer will not be held liable for any damage or injury which may result from the failure to fulfil this requirement.
• Do not use adapters, multiple sockets and two-wire extension leads. If it is necessary to use the extension lead, it must be equipped with a protection ring and a single socket and must have a VDE/GS safety certificate.
• If an extension lead is used (with a protection ring and safety certificate), its socket must be located at a safe distance, away from the sinks, and must not be in a place where it could be flooded by water or waste water.
• Make sure the appliance can be easily disconnected from the mains, either by pulling the plug out of the mains socket, or by switching the two-pole switch off.

Climate range

The information about the climate range of the appliance is provided on the rated plate. It indicates at which ambient temperature (that is, room temperature, in which the appliance is working) the operation of the appliance is optimal (proper).

Climate class Allowable ambient temperature

SN	Extended Temperate	This refrigeration appliance is intended for use at an ambient temperature ranging between 10°C and 32°C
N Temperate		This refrigeration appliance is intended for use at an ambient temperature ranging between 16 °C and 32°C
ST Subtropical		This refrigeration appliance is intended for use at an ambient temperature ranging between 16 °C and 38 °C
T Tropical		This refrigeration appliance is intended for use at an ambient temperature ranging between 16 °C and 43 °C

PRACTICAL EVERYDAY TIPS

- If the light inside the appliance remains turned on, keep in mind that the temperature inside the appliance will be higher

- Temperature inside the appliance depends on the amount and type of stored wine bottles

- To ensure user safety and high quality of stored wine, do not install the appliance in damp rooms

- Store wine bottles in designated spaces

- Your wine cooler has a limited capacity. Do not place more bottles in your wine cooler than recommended in specification

- Do not open the wine cooler door if it is not necessary

- Do not cover the shelves with aluminium foil or other material. This blocks the air circulation inside the appliance

- To avoid damage to the door seal, make sure that the door is completely open before pulling out the shelf. The shelves should be inserted as far as possible, otherwise the shelf may deform and damage the door seal.

- Do not extend the loaded shelves beyond the extension limit (about 1/3 of the shelf length)

- This appliance is designed for storing bottles of wine. Do not use it for any other purpose.

• Temperature stability is very important when storing wine.

- Exposing your wine cooler to sunlight, significant temperature fluctuations, high humidity and vibrations may cause the wine to go bad.

- In periods of high humidity, condensed water vapour may appear on the outer surfaces of the glass door. To prevent this, install the appliance in a dry, adequately ventilated room.

- Selected models have an external handle. You need to install it on your own. Do not use electric tools for this purpose (fig. 3*). To do this, pull the door seal slightly to the side and place the screws on the inside of the door. Align the handle with the holes on the outside of the door and tighten the screws with a screwdriver. Reinstall the door seal.

- The maximum capacity of the appliance is given in the product sheet enclosed with the wine cooler. This capacity applies to standard 0.75 litre bottles of Bordeaux.

- Selected models have an Anti-tip kit. Install it according to the enclosed diagram (fig. 6*).

- This refrigeration appliance is intended for use as a built-in appliance.

- To achieve the most effective food preservation for the longest possible time and to avoid wasting any food, position the products as shown in Figure 12. In addition, this figure illustrates the layout of drawers, baskets and shelves, which allows the most efficient use of energy.

- Optimal temperature and storage conditions will extend product shelf life and optimize electricity consumption. Optimal storage temperature range should be stated on the food product packaging.

UNPACKING

Simple line drawing of a three chasing recycling symbol (no text or labels)

During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment.

All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.

Important! Packaging materials (bags, polyethylene, polystyrene, etc.) should be kept away from children during unpacking.

DISPOSAL OF OLD APPLIANCE

Simple line drawing of a trash bin with crossed lines indicating no waste or prohibition (no text or symbols)

In accordance with European Directive 2012/19/EU and local legislation regarding used electrical and electronic goods, this appliance is marked with the symbol of the crossed-out waste container. This marking indicates that the appliance must not be disposed of together with other household waste after it has been used.

The user is obliged to hand it over to waste collection centre collecting used electrical and electronic goods. The collectors, including local collection points, shops and local authority departments provide recycling schemes.

Proper handling of used electrical and electronic goods helps avoid environmental and health hazards resulting from the presence of dangerous components and the inappropriate storage and processing of such goods.

CONTROLS

Appliance controls- single and dual zone

The control panel is shown in figure 4. For reference it is also shown below:

Single zone

Dual zone

① - Power button
- Light button
+ - "+" button
- “-” button

To switch the power on/off

Press and hold the power button for one second to switch the wine cooler on.

Press and hold the power button for five seconds to switch the wine cooler off.

Note: Turn off your appliance by unplugging the power cord from the wall outlet.

To change the temperature

• Press the "+" or "-" buttons until the required temperature is shown on the display.
• The Preset temperature is 12^ / 54^ . (for single zone models)
• For dual zone models: For the upper/left zone, the default temperature setting is 8°C/46°F, and for the lower/right zone, the default temperature setting is 12°C/54°F.
• To view the set temperature, touch the "+" or "-" button at any time and the set temperature will flash in the LED display for five seconds.
• The display shows the current internal temperature when the wine cooler is on.

Note: The temperature in the lower zone must be set either the same as or higher than the temperature in the upper zone.

Optimal temperature selection

Whilst wine is best stored at temperatures between 13 and 15°C, your wine can also be stored at drinking temperature. For red wine this is between 15 and 17°C, and for white wine between 12 and 13°C.

Indoor lighting

Press and hold the light button for 5 seconds to turn the light on or off. Activation is indicated a dot on the display.

Settings mode

Some settings are available depending on the mode.

Set the temperature unit °F or °C.

Touch and hold +for 5 seconds, then use and to-set the unit. Touch ① to confirm. Touch +for 5 seconds to exit.

Set the display backlight intensity

Touch and hold +for 5 seconds, then touch once. Now use and to set the display backlight intensity. The default setting is d1. Touch to confirm. Touch +for 5 seconds to exit.

Set the appliance interior lighting intensity.

Touch and hold +for 5 seconds, then touch twice. Now use and to set the interior lighting intensity. The default setting is L3 Touch to confirm. Touch +for 5 seconds to exit.

Set sounds.

Touch and hold + for 5 seconds, then touch four times. Now use + and - to set the sounds. The default setting is S1. The possible settings are as follows:

S0: Touch sensor sound ON / Audio alarm OFF
S1: Touch sensor sound ON / Audio alarm ON
S2: Touch sensor sound OFF / Audio alarm OFF
S3: Touch sensor sound OFF / Audio alarm ON
Touch ☐ to confirm. Touch ☐ for 5 seconds to exit.

Internal Humidity

According to the model wine coolers are equipped with a humidity system to maintain optimal humidity within the wine cooler. Fill the humidity reservoir approximately 3/4 full with water. Place the reservoir on the runners on the top shelf as shown in fig. 2. Ensure it is located correctly to prevent water spillage. Check the water level regularly and refill if required.

Temperature display

The temperature display will show the current internal temperature. The display flashes:

• When a different temperature is being set
• If the internal temperature is +/- 5^ away from the set temperature. This serves as a warning to prevent damage to the contents of the appliance should the temperature be too high.

Silent Mode

Touch and hold + for 5 seconds, then touch three times. Now use + an - to set the silent mode (F0). When the required temperature is reached, the appliance operates without the fan. This is the default mode of the wine cooler.

Dynamic cooling mode

Touch and hold + for 5 seconds, then touch three times. Now use + and - to set the dynamic mode (F1- half time, F2- full time). The fan alternately turns on and off to maintain air circulation even when the required temperature is reached. This ensures uniform and stable humidity and temperature in the wine cooler for ideal long-term wine storage conditions.

Weekend mode

This will switch off the displays, interior light and audible alarms. The cooling process will continue.

To switch the Weekend mode on, touch and hold the power and light keys simultaneously for five seconds. The indicator light will flash four times and confirm the mode is on. Mode will switch off automatically after 48 hours, but to switch the mode off at any time, touch and hold the power and light keys simultaneously for five seconds.

Temperature alarm

If the temperature rises or falls outside the set temperature range, an alarm will sound and the display will flash. This may be because:

• The wine cooler has not yet reached the set temperature (when first switched on).
  • There has been a power failure.
  • The wine cooler has been overloaded.
• The door is not closed properly.

CARE AND CLEANING

Always disconnect the appliance from the mains electrical supply before any cleaning or maintenance.

Removing the shelves

• To remove a shelf from the wine cooler, first remove all bottles from the shelf, then pull the shelf forwards until the groove on either side of the shelf is level with the plastic peg on either side of the cabinet (as shown in fig 5). Then lift the shelf up and pull forwards.
• To replace the shelves, follow the steps above in reverse order.

Cleaning

• Do not use abrasive products or detergents. After washing, rinse and dry thoroughly.
• The exterior of the appliance and the door seal should be cleaned using mild soapy water and dried thoroughly.
• The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water.
• Clean the shelves separately by hand using soap and water. Do not put them in the dishwasher.
• Ensure that the cloth is only moist when cleaning the control panel and electrical parts, and that all water is thoroughly dried off before reconnecting the power.
• Once cleaning is complete, reconnect the mains electrical supply.
• If the appliance is not to be used for prolonged periods of time, unplug and clean the appliance thoroughly. The door should be left slightly ajar to prevent the formation of odours or condensation

TROUBLESHOOTING

If you have any problems with your appliance, you should check the troubleshooting guide prior to calling Call Center to prevent unnecessary service calls and potential cost.

If the appliance is not working, check

• There is power to the appliance
- The house fuses or circuit breakers are intact and the fuse in the plug has not blown.
- The plug socket is functioning correctly. To check this, plug another electrical appliance in to see if the socket is working.
- The ambient temperature is between 16^ to 32^ .

The appliance is working, but not very well, check

• The appliance is not overloaded.
• The thermostat is set to an appropriate temperature.
• The door is closing properly.
  • The door gasket is sealing properly
• There is enough ventilation at the side and rear walls.
• The ambient temperature is between 16^ to 32^ .

The appliance is noisy, check

• The appliance is level and stable.
• The cooling gas will make some noise, even when the compressor is not running.
• During operation, it is normal for the fan to run, even when the compressor is not running.

The light does not work, check

• There is power to the appliance.
• The house fuses or circuit breakers are intact and the fuse in the plug has not blown.
• The light button is not set to off.

Please note:

The LED lighting cannot be replaced without a service call

The door will not close properly, check

• The appliance is level and stable.
• If the door has been removed, it may not have been correctly refitted.
  • The door seal is dirty.
• The shelves are not positioned correctly.

The display shows "E1" or "E2"

- The temperature sensor has failed. Please contact Call Center

EPREL

For more information about the product, please refer to the EU EPREL Product Database at https://eprel.ec.europa.eu. For more information, please use your mobile device to scan the QR code on the energy label or enter the product model listed on the energy label in the EPREL search engine https://eprel.ec.europa.eu/

WARRANTY AND AFTER SALES SERVICE

Warranty

Warranty service as stated on the warranty card. The manufacturer shall not be held liable for any damage caused by improper use of the product.

Service

• The manufacturer recommends that all repairs and adjustments be carried out by the Factory Service Technician or the Manufacturer's Authorized Service Point. For safety reasons, repairs should be referred to professionals.
• Repairs carried out by unqualified persons may seriously endanger the appliance user.
• The minimum warranty period for the appliance offered by the manufacturer, importer or authorized representative is given in the warranty card.
• The warranty shall be void if you make any independent adaptations or alterations, tamper with seals or other appliance safety devices or its parts or interfere with the appliance contrary to operating instructions.

In the event of appliance malfunction, request assistance or repair.

If your appliance needs repair, please contact the service centre. Please see warranty card for address and contact details of our service centre. Before contacting us, please have ready the appliance serial number, which can be found on the identification sticker: For your convenience, please write it down below:

Manufacturer's Declaration

The manufacturer hereby declares that this product meets the requirements of the following European directives:

• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility (EMC) Directive 2014/30/EU
• ErP Directive 2009/125/EC
• Directive RoHS 2011/65/EU

and has thus been marked with the and symbol and been issued with a declaration of compliance made available to market regulators.

BÄSTA KUND!

Recycling symbol composed of three chasing arrows forming a triangle (no text or labels)

Symbol of a trash bin crossed out by two diagonal lines (no text or numbers present)

Två zoner

① - Strömknapp
- Belysningsknapp
+ - "+"-knapp
- -"-"-knapp

EN:

- The base under the wine cooler must be cut as instructed

- Since the appliance will be built into a furniture unit, before installing the appliance, prepare a ventilation duct behind the appliance running from the floor to the top of the furniture unit. Ensure there is free space between the back of the appliance and the wall, which is not blocked by furniture. The area of ventilation grille should be at least 300 cm ^2

- To ensure correct appliance operation never cover any ventilation openings. Regularly clean the ventilation grille.

SV:

Technical line drawing of a door assembly with mounting holes and internal components (no text or symbols)

2

Technical line drawing of a cabinet or enclosure with mounting holes and internal components, showing no text or symbols.

1

Line drawing of a rectangular box placed on a metal platform, with no text or symbols present.

2

3

4

Technical line drawing of a mechanical component with flanges and a small inset view (no text or symbols)

8 7 8 8 8 6 45

Line drawing of a multi-level refrigerator with circular compartments and ventilation grilles (no text or symbols)

Two identical line drawings of wine bottles arranged in rows, with no text, numbers, or symbols present.

12

Service

Vi har service i hela Sverige/ Nationwide service in Sweden

Besök www.cylinda.se / Visit www.cylinda.se

Ring 0771-25 25 00 (endast lokaltaxa) / Call 0771-25 25 00

Uppge / Declare

Maskintyp / Model code

Serienummer / Serial number

Inköpsdatum / Purchase date

Problembeskrivning / Problem description