XKJ-1305S - Water pump Cotech - Free user manual and instructions

Product Type	Water Pump
Model	XKJ-1305S
Brand	Cotech
Power Supply	230V ~ 50Hz
Power Consumption	750 W
Max Flow Rate	5000 L/h
Max Head	35 m
Max Liquid Temperature	35 °C
Max Particle Size	1 mm
Housing Material	Stainless Steel / Plastic
Impeller Material	Technopolymer
Seal Type	Mechanical Seal
Protection Class	IP68
Dimensions (W x H x D)	20 x 30 x 20 cm
Weight	5 kg
Power Cable Length	10 m
Functions	Drainage, transfer, circulation
Maintenance	Regular cleaning of filter; check seals annually
Safety	Thermal overload protection; automatic shut-off
Spare Parts	Impeller, seal kit, cable
Repairability	Repairable; spare parts available separately

Frequently Asked Questions - XKJ-1305S Cotech

How do I install the Cotech XKJ-1305S water pump?

Place the pump on a stable, level surface. Connect the inlet and outlet hoses securely. Ensure the power cord is undamaged and plug into a grounded outlet. The pump must be fully submerged for proper cooling.

Do I need to prime the pump before use?

Yes, fill the pump housing with water through the outlet port until water flows out. This prevents dry running, which can damage the mechanical seal.

What is the maximum water temperature the pump can handle?

The maximum allowed water temperature is 35 °C. Do not exceed this to avoid damage to internal components.

How do I clean the pump filter?

Disconnect power. Remove the inlet filter screen and rinse it with clean water. Reinstall before use. Clean after each use or when flow decreases.

Why is the pump not starting?

Check power supply and fuse. Ensure the pump is correctly primed and not blocked by debris. The thermal overload protection may have tripped; let the pump cool for 30 minutes.

Can the pump run dry?

No, running dry for more than a few seconds can damage the pump. Always ensure the pump is submerged or filled with water before operation.

What maintenance is required?

Regularly clean the filter and remove any debris. Check the power cable for damage. Annually inspect the mechanical seal and replace if worn.

How should I store the pump in winter?

Drain all water from the pump. Clean and dry it. Store in a frost-free environment. Remove the impeller cover and apply a light oil to the shaft.

Are spare parts available for this model?

Yes, common spare parts such as the impeller, seal kit, and power cable are available from Cotech or authorized dealers.

What is the warranty period for Cotech XKJ-1305S?

Cotech typically offers a 2-year warranty from date of purchase covering manufacturing defects. Retain your receipt.

USER MANUAL XKJ-1305S Cotech

Read the entire instruction manual carefully and make sure that you fully understand it before you use the equipment. Keep the manual for future reference.

Viktig information:

Technical line drawing of an electric motor with attached housing and mounting base (no text or symbols)

ART.NO

18-3114

30-1004

MODEL

XKJ-1305S-UK

XKJ-1305S

Ver. 20150126

Original instructions

Bruksanvisning i original

Please read the entire instruction manual before using the product and save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data. If you have any questions regarding technical problems please contact our Customer Services (see address on reverse).

Safety

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• The mains lead should be checked regularly. Never use the product if the mains lead or plug is damaged.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Use the pump only as described in this instruction manual.
• Always use a residual current device (RCD or RCCB) which trips at < 30 mA between the pump and the power supply.

• Always inspect the pump before using it, especially the power lead and plug. Never use the pump if any of the parts is damaged.

• Make sure that the pump and all electrical connections (extension lead, RCD, etc) are placed in a dry place and protected from rain, moisture and high water level. The temperature should not exceed 35 °C.

• Do not expose the mains lead to extreme heat, oil or sharp edges.
• Keep children and animals away from the pump when it is running.
• The pump must not be used for corrosive, flammable or explosive liquids such as petrol, kerosene or thinners.
• The pump should also not be used for grease, oil, saltwater, brackish water, urine or toilet sewage water.
• The pumped liquid's temperature must not exceed 35 ^ C.
• Keep everyone out of the liquid (pool, etc.) being pumped.
• The operator of the pump is responsible for the safety of the pump and all its applications.
  • Always unplug the pump before adjusting, repairing, etc.
• Do not expose the pump directly to jets of water.
• The pump should only be repaired by a qualified electrician using original parts.
• The pump must not be run dry since this will wear out the pump. Turn off the pump as soon as water has stopped coming out of the hose. The guarantee will be void if the pump is damaged due to dry running.
• The pump must only be used by those who have read the instruction manual. Keep children and animals away from the pump, especially if it is under pressure.

Product Description

Operating Range

The pump is intended for domestic use; in the home and garden.

Suitable uses:

• Watering gardens, vegetable gardens, lawns, etc.
- Pumping water from springs, wells, water containers, etc.

Note: The pump is only designed for pumping clean water except drinking water.

Parts

1. Drain plug
2. Pressure hose connection (Female R25,1")

3. Suction hose connection (Female R25)

4. Filler plug

5. Handle

6. Power switch

Before using

Placement

Prevent water damage. Pre-planning prevents accidents!

Leakage in the pump and hoses may occur through freezing, incorrect installation, pressure surges, etc. The pump should therefore be placed in a waterproof environment approved by your insurance company and your insurance policy.

Contact your insurance company if you are unsure.

Place the pump on a firm, hard surface, well protected from water spray.

Suction hose connection

• Connect a 25 mm (1") diameter hose to the suction hose connection (R25) on the pump.
• The suction hose should be equipped with a foot valve with a non-return valve that is placed at the end of the suction hose (pipe).
• Place the suction hose so that it slopes upwards from the water to the pump inlet connection.
• The suction hose must always be on a lower level than the inlet to the pump. Air-pockets in the hose could disrupt the pump's operation.
• Hoses or pipes must not be connected in such a way as to exert any pulling strain or tensile stress on the pump unit.
• The foot valve should be anchored to the bottom so that the pump does not run dry if the water level drops.
• The suction hose assembly must be air-tight to prevent air from being sucked into the pump.
• A filter should be fitted to the suction side to prevent sand, mud, etc from being sucked into the pump.

Pressure hose connection (outlet)

Connect a hose with a min.12.5 mm (1/2") diameter to the outlet connection (R25).

Mains connection

• Connect the mains lead to an RCD protected earthed socket for personal safety.
• The pump has a built-in thermal motor protection and automatically shuts off when overheating (and re-starts automatically when cooled).

Starting the pump

1. Place the pump on a firm, hard surface, well protected from water spray.
2. Connect the suction hose to the suction inlet (3).
3. Connect the mains lead to an RCD protected earthed socket for personal safety.
4. Fill the pump housing with water via the filler hole (4).
5. Connect the pressure hose to the outlet connection (2).
6. Turn the pump on using the power switch (6). It can take from four to six minutes for the pump to reach maximum effectiveness, depending on the pressure head, and amount of air on the suction side. Fill the pump with water via the filler hole (4) once more if the pump does not work satisfactorily after six minutes.
7. If the pump is detached and reattached the pump unit should be filled with water via the filler hole (4).

Maintenance

• Always unplug the pump before carrying out any kind of maintenance.
- Use a soft lightly moistened cloth to clean the plastic pump parts. Never clean the product using strong detergents or solvents.
- If there is a risk of frost or if the pump is not being used during winter it should be emptied of water. Store the pump in a dry place.
- If the pump has not been run for a while it is a good idea to check that the rotor moves freely by quickly turning the pump on and off.
- The pump should be checked regularly. Check the operation and inspect for any damage.

General guidelines

• Dry running of the pump should be avoided because it increases wear.
• Pull the plug not the lead when unplugging the pump from the mains.
• Never lift or carry the pump by its power lead.
• Sand and other abrasive substances in the liquid that is pumped will increase wear and tear and reduce the capacity of the pump.
• Make sure that the recommended suction head (8 m) is not exceeded.
• Protect the pump from frost.
• The pump is designed for intermittent use, not continual operation such as for a fountain.

Troubleshooting

Problem Possible Cause Remedy
The pump does not start.	No power supply. Check fuses and RCD,etc.
	Dirt lodged in the pump. Remove any dirt or deposits.
	The thermal protection device has triggered.	Unplug and clean the pump Remember that the max. liquid temperature cannot exceed 35 °C.
The pump is running but does not pump.	There is air in the pump. Open all nozzles and valves etc. so the air can pass through.
	The suction hose is above the water's surface.	Place it below the water surface.
	Suction hose leaking. Tighten, or seal the leak.
	Max. suction head exceeded. Check suction head (max. 8 m).
	Max. pressure head exceeded. Check pressure head (max. 46 m).
The pump has diminished capacity or low pressure.	Max. suction head exceeded. Check suction head (max. 8 m).
	Max. pressure head exceeded. Check pressure head (max. 46 m).
	The suction hose is above the water level.	Place it below the water surface.
	Dirt lodged in the pump. Remove any dirt or deposits.
The pump stops suddenly.	The thermal protection device has triggered.	Unplug and clean the pump. Remember that the max. liquid temperature cannot exceed 35 °C.

Disposal

Follow local ordinances when disposing of this product. If you are unsure of how to dispose of this product, please contact your municipality.

Specifications

Rated power 1300 W

Rated voltage 230 V AC, 50 Hz

Max. pump capacity 65 l/min

Max. pressure 4.6 bar

Max. water temperature 35 °C

Max. pressure head 46 metres

Max. suction head 8 metres

Hose connections R25 female thread

Size 38 × 25 cm

Weight 9.8 kg

Trädgårdspump 1300 W

ART.NR 18-3114 MODELL XKJ-1305S-UK

30-1004

XKJ-1305S

Declaration of Conformity

Declares that this product complies with the requirements of the following directives and standards

Machinery directive 2006/42/EC

EMC directive 2004/108/EC

Low voltage directive 2006/95/EC

EN 55014-1:2006+A1+A2

EN 60335-1:2012

EN 55014-2:1997+A1+A2

EN 60335-2-41:2003

EN 61000-3-2:2006+A1+A2

+A1+A2

EN 61000-3-3:2008

EN 62233:2008

President

Insjön, Sweden, 2013-10-31

SVERIGE

KUNDTJÄNST Tel: [phone]

Fax: [phone]

E-post: [e-mail]

INTERNET www.clasohlson.se

BREV Clas Ohlson AB, 793 85 INSJÖN

NORGE

KUNDESENTER Tlf.: 23 21 40 00

Faks: 23 21 40 80

E-post: [e-mail]

INTERNETT www.clasohlson.no

POST Clas Ohlson AS, Postboks 485 Sentrum, 0105 OSLO

SUOMI

ASIAKASPALVELU Puh.: 020 111 2222

POSTAL 10 – 13 Market Place

Kingston Upon Thames

Surrey

KT1 1JZ

DEUTSCHLAND